Olimpia splendid B0969 User Manual page 105

2. SET EXTERNAL STATIC PRESSURE
ck that both power supply wiring and duct installation have been completed Check that
• You can use the unit's automatic air ow adjustment function to set external static pressure.
closing dampers are open.
• Automatic air ow adjustment is the volume of blow-o air that has been automatically
ck that the air lter is properly attached to the air suction side passage of the unit.
sing the wire controller to set external static pressure (some air conditioners) .
adjusted to the quantity rated.
the parameters for automatic air ow adjustment. When the air conditioning unit is o ,
You can use the unit's automatic air ow adjustment function to set external static pressure.
1. Make sure the test run is done with a dry coil. If the coil is not dry, run the unit for 2 hours in
orm the follwoing steps:
Automatic air ow adjustment is the volume of blow-o air that has been automatically
FAN ONLY mode to dry the coil.
ss"COPY" long.
adjusted to the quantity rated.
2. Check that both power supply wiring and duct installation have been completed Check that
ss "+" or "-" to select the AF.
Make sure the test run is done with a dry coil. If the coil is not dry, run the unit for 2 hours in
any closing dampers are open.
FAN ONLY mode to dry the coil. ss "CONFIRM". The air conditioning
Check that the air lter is properly attached to the air suction side passage of the unit.
it will then start the fan for air ow
Check that both power supply wiring and duct installation have been completed Check that
3. Set the parameters for automatic air ow adjustment. When the air conditioning unit is o ,
tomatic adjustment.
any closing dampers are open.
perform the follwoing steps:
Check that the air lter is properly attached to the air suction side passage of the unit.
- Press"COPY" long.
OT adjust the dampers when automatic airflow adjustment is active.
Set the parameters for automatic air ow adjustment. When the air conditioning unit is o ,
- Press "+" or "-" to select the AF.
perform the follwoing steps:
to 6 minutes, the air conditioning unit stops operating once automatic airflow
- Press "CONFIRM". The air conditioning
- Press"COPY" long.
ment has finished.
unit will then start the fan for air ow
- Press "+" or "-" to select the AF.
automatic adjustment.
the wire controller to set airflow rate (some air conditioners) .
- Press "CONFIRM". The air conditioning
the air conditioning unit is off, perform the follwoing steps:
unit will then start the fan for air ow
DO NOT adjust the dampers when automatic airflow adjustment is active.
ss"COPY" long.
automatic adjustment.
After 3 to 6 minutes, the air conditioning unit stops operating once automatic airflow
ss "+" or "-" to select the SP.
adjustment has finished.
ss "CONFIRM" to set the air ow.
O NOT adjust the dampers when automatic airflow adjustment is active.
means a stable air ow volume, 1 to 4 means an increase in air ow volume.
Using the wire controller to set airflow rate (some air conditioners) .
ter 3 to 6 minutes, the air conditioning unit stops operating once automatic airflow
ss "BACK" to nish the setting.
When the air conditioning unit is off, perform the follwoing steps:
justment has finished.
Den kabelgebundenen Regler benutzen, um die Luftstromstärke
- Press"COPY" long.
einzustellen (bei einigen Klimageräten)
sing the wire controller to set airflow rate (some air conditioners) .
- Press "+" or "-" to select the SP.
Bei ausgeschaltetem Klimagerät, folgende Schritte ausführen:
hen the air conditioning unit is off, perform the follwoing steps:
- Press "CONFIRM" to set the air ow.
- Press"COPY" long.
0 means a stable air ow volume, 1 to 4 means an increase in air ow volume.
- Press "+" or "-" to select the SP.
- Press "BACK" to nish the setting.
- Press "CONFIRM" to set the air ow.
0 means a stable air ow volume, 1 to 4 means an increase in air ow volume.
- Press "BACK" to nish the setting.
LCAC
• Die Parameter der automatischen Luftstromanpassung einstellen.
Bei ausgeschaltetem Klimagerät, folgende Schritte ausführen:
Länger „COPY" drücken.
„+" oder „-" drücken, um AF zu wählen.
„BESTÄTIGEN" drücken. Das Klimagerät schaltet dann den Lüfter
für die automatische Luftstromanpassung ein.
AN wird blinken, wenn der Lüfter während der
automatischen Luftstromanpassung eingeschaltet ist.
• Die Klappen während der automatischen Luftstromanpassung NICHT
bewegen.
Nach 3 bis 6 Minuten hält der Betrieb des Klimageräts an, wenn die
automatische Luftstromanpassung beendet ist.
• Länger „COPY" drücken.
• „+" oder „-" drücken, um SP zu wählen.
• „BESTÄTIGEN" drücken, um den Luftstrom einzustellen.
0 bedeutet ein gleichmäßiges Luftstromvolumen, 1 bis 4 bedeutet
eine Zunahme der Luftstrommenge.
• „ZURÜCK" drücken, um die Einstellung zu beenden.
ON will ash during when the
fan is on during automatic
air ow adjustment.
ON will ash during when the
fan is on during automatic
air ow adjustment.
ON will ash during when the
fan is on during automatic
air ow adjustment.
30
30
30
DE - 27