Advertisement
Quick Links
Advertisement
Related Manuals for Sanden Vendo G-SNACK
Summary of Contents for Sanden Vendo G-SNACK
- Page 1 G-SNACK / G-SNACK PLUS MASTER & SLAVE PROGRAMMING MANUAL...
- Page 2 SandenVendo Europe S.p.A. Regione Cavallino, 2 15030 Coniolo (AL) Italy Tel.:+ 39 0142 335111 Fax.:+ 39 0142 562348 E-Mail: info@sandenvendo.it www.sandenvendo.com SandenVendo GmbH Contact SandenVendo France Jean-François Suteau: 0033 6 67 38 43 26 Spangerstrasse 22 jfsuteau@sandenvendo.be D–40599 Dusseldorf Michel Mirczewski: 0033 6 11 01 67 65 Germany mmirczewski@sandenvendo.be Tel.: + 49 (0) 211 740390...
- Page 4 SANDENVENDO SPECIFICATION FOR ELECTRONIC BOARD SF01 HARDWARE FEATURE Power supply : 24 Volt AC 2 A rms Motor outputs 24 VDC 1 A Motor micro-switches Sold-out micro-switches Sold-out leds Selections switches Door switch Analogics inputs (for temperature control) Real time clock Jack plug for DEX/UCS audit output.
- Page 5 FUNCTION OF THE SELECTION BUTTONS Selection Nr.: 1 Home Abort or escape a programming ⌫ ⌫ ⌫ ⌫ point Selection Nr.: 2 Increase or next programming point by pushing selection button 2 Selection Nr.: 3 Down Decrease or previous programming point by pushing selection button 3 Selection Nr.: 4 Enter / Store...
- Page 6 SERVICE ROUTINE In the service mode, information such as sales by selection, total sales, total cash flow through the machine, and diagnostic error codes can be accessed by using the selection buttons and the electronic display. In addition, storage column assignments and vend pricing can be set in this mode using the same techniques.
- Page 7 ERROR ROUTINE If the ENTER button is activated at the "EROR" prompt the VMC will enter in the error routine. If no errors have occurred since the last error reset the display will show a "NONE" message. If an error has been detected since the last error reset the display will show the first summary level error code that has occurred, such as "COLJ", which would indicate a column jam error.
- Page 8 CONTROL ERROR ROUTINE If the ENTER button is activated at the "CTRL" prompt the VMC will display the kind of control error, possible error is: "DS" Door switch,. the door was opened for more than 1 hour, this is considered as a door switch not working well.
- Page 9 BILL VALIDATOR ERROR ROUTINE If the ENTER button is activated at the "BVAL" prompt the VMC will display a "BC" message indicating a bill validator communication error, a "BFUL" message indicating that the bill stacker is full, a "BILL" message indicating a defective motor, a "BJ"...
- Page 10 COIN PAYOUT ROUTINE (work only on MDB) If the ENTER button is activated at the "CPO" prompt the VMC will enter the coin payout routine. Upon entry into this routine the display will show the lowest coin value dispensable. Pressing the UP button will increase the display to the next highest coin value, the DOWN will decrease to the next lowest coin values.
- Page 11 “ VEND “ Activation of the ENTER button (at the “ VEND “ routine) will show the column number “CXY” (X is number of row, Y is number of column). Activation of the enter button will perform the vending TEST for selected column, using the up or down button will change the column number.
- Page 12 “LIFT” Entering this routine the display will show near the word “LIFT”, 5 values (0 or 1) that indicate the lift status: 1 if 0 the main board of the lift works correctly, if 1 the board doesn’t work. 2 if 0 the micro switch on delivery lift position is not pressed, if 1 the micro switch is pushed ( or disconnected since is N.C.
- Page 13 Pressing button “0” the machine will show “CLEAR”, if you want to clear all the counter (also the historical counter), you must digit the programming password (2-3-1-4) correctly, otherwise the counter are not cleared. Activation of the HOME button while a selection counter is displayed will return the VMC to the "CASH"...
- Page 14 SLAVE PRICE SETTING ROUTINE (PROTECTED MENU SHOWN ONLY IF SLAVE IS ENABLED) The function is the same as the previous menu, only the set prices are for the Slave machine, and the menu is called “PRIC S” MASTER SPACE TO SALES SETTING ROUTINE (PROTECTED MENU) This function is used to recognise the number and the position of the motors installed in the machine.
- Page 15 THE FOLLOWING INFORMATION DESCRIBES VARIOUS MACHINE CONFIGURATION SETTINGS CASHLESS SYSTEM PRICE (ONLY MDB) This setting is used to allow different vend price with cashless MDB: C01 = 0 same price for Coinage and cashless C01 = 1 different price for Coinage and cashless SLAVE ENABLE (EXTENDED MENU) This parameter enables or disables the slave machine and relative programming menu: C02 = 0 Slave machine not installed, normal menu.
- Page 16 SOLD-OUT MODE This parameter is used to enable sold-out status of the spirals; if it’s enable (C6 = 1) when the optical barrier doesn’t detect the product, the VMC set the spiral in sold-out status. This feature is applied for master and slave. The sold-out are cleared (also for the slave) when the door of the master is open.
- Page 17 LIFT ENABLE This parameter enable the lift (optional kit): C11 = 0 Lift disable (default) C11 = 1 Lift enable. LIFT EXTRA MOVEMENT This parameter enable (if lift is enable in C11) an additional movement on second vend attempt to facilitate the product delivery: C12 = 0 No additional movement.
- Page 18 CORRECT CHANGE ONLY CONTROL (protected menu) CORRECT CHANGE RULE (MDB only) IF IN CCOC CON = 0 VMC manages automatically the changer setting CCU correct change value If (changer is able to change back (CCU value + Maximum Price))correct change message is not showed otherwise correct change message will be show.
- Page 19 CONFY COINAGE KEYPAD ACTIVATION (COINAGE MDB) C01 = 0 Disabled C01 = 1 Enabled LOW CHANGE EQUATION (MDB MODE) This parameter defines the exact change equation. The combination of the empty states assume the exact change state A is the lowest coin value reported in the tubes E is the highest coin value reported in the tubes If the tubes are empty according to these equations the CORRECT CHANGE LED is ON...
- Page 20 PRICE HOLDING (EXECUTIVE MODE) If you set C2 = 1 and payment system is set to Executive, the machine works in price holding mode; it means that the price is stored on payment system. On this mode each time you press a selection the machine sends to the payment system the number of selection pressed in the following format: Sel 11 pressed –...
Need help?
Do you have a question about the Vendo G-SNACK and is the answer not in the manual?
Questions and answers