Page 2
Storage temperature: –20 °C to +60 °C Approx. 14.1 Megapixels (USB 2.0 compliant) (–4 °F to +140 °F) Lens: Sony G 10× zoom lens Dimensions: Approx. 55 × 24 × 83 mm f = 4.25 mm – 42.5 mm (25 mm – [LCD screen] (2 1/4 ×...
Page 3
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
1. SERVICE NOTE 1-1. PRECAUTION ON REPLACING THE SY-255 BOARD 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) DESTINATION DATA When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
1-3. HOW TO WRITE DATA TO INTERNAL MEMORY 1-4. SELF-DIAGNOSIS FUNCTION Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. 1-4-1. Self-diagnosis Function 1-4-2. Self-diagnosis Display This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
1-4-3. Self-diagnosis Code Table 1-5. PROCESS AFTER FIXING FLASH ERROR Self-diagnosis Code When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated.
1-6 . ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD 1-7. CAM TUBE BLOCK REPLACING METHOD Removal Removal 1 Turn on the power switch and extend the lens. 1 Remove the four soldering, and disconnect the flexible board form the connector. 2 Detach the battery.
Page 8
4 Remove the spring from the hook. 0 Remove the Fixed Stationary Tube. 5 Remove the five screws, and remove the Rear Mirror Plate. qa Rotate the Cam Tube Block Assy. qs Remove the 1 Group Assy. Screws Rear Mirror Plate Screws Fixed Stationary Tube...
Page 9
Installation 8 Install the Cam Tube Assy to 1 Group Assy with aligning gear edge of Cam tube Assy with triangle-shaped projection of 1 Group Assy. 1 Install Straight Tube B to Cam Tube Block Assy with aligning the positions as shown in figure. 9 Rotate the 1 Group Assy with tucking it slightly.
Page 10
qf Install the Naruto Gear. (up side is shallow hole side.) qk Install the spring to hook. ql Rotate the Naruto Gear and the lens is retracticle. Naruto Gear Up side Hook Spring Down side qg Extension the lens by turning the Naruto Gear. w;...
1-8-2. Inspection When Cam Tube Block Is Replaced 1-8. FINAL INSPECTION Focus check 1-8-1. Confirm There Is No Fault In Actual Motion/Actual Screen 1 Preparation Inspect it as follows when you exchange parts in the lens block. • Camera installed re-assemble lens. 1 Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º) •...
Page 12
2. REPAIR PARTS LIST IDENTIFYING PARTS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original Follow the disassembly in the numerical order given. The components identified by mark 0 one. or dotted line with mark 0 are critical for •...
Page 13
NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked Cut and remove the part of gilt of bent at the terminal. which comes off at the point. Do not insert the cable insufficiently nor crookedly. (Be careful or some pieces of gilt may be left inside) •...
Page 14
2-1. EXPLODED VIEWS DISASSEMBLY 2-1-1. REAR SECTION 1. Remove to numerical order ( ) in the left figure. #65 / #147 X 2 #65 / #147 X 1 Bottom View Bottom View #147 #147 LCD901 #65 / #147 X 4 Right View Left View #147...
Page 15
2-1-2. TOP SECTION DISASSEMBLY ns: not supplied 1. Remove to numerical order to 9) in the left figure. Disconnect Flexible board (8-1) → #23 X 1 → Slide top section (8-2) Back View Back View Back View DISCHARGING OF THE CHARGING CAPACITOR Screw #23: M1.7 X 4.0 (Tapping) #177: M1.4 X 2.5...
Page 16
2-1-3. FRONT SECTION DISASSEMBLY ns: not supplied 1. Remove to numerical order to qj) in the left figure. #23 X 1 Back View BT901 BT001 Back View Claws Claw (Note) Lens Block Section Screw (See page 2-6) #23: M1.7 X 4.0 (Tapping) (Black) 3-080-204-11 SP901...
Page 17
2-1-4. LENS BLOCK SECTION DISASSEMBLY ns: not supplied 1. The meaning of the sign in left figure is as follows. Be careful when it removes. ◇: Solder Screw #30: M1.2 X 3.5 (Tapping) (White) 3-086-156-11 (including IC001 (Note 1, 2) (CCD imager)) (Note 3) (Note 4)
Page 19
AF-129 BT-059 MS-436 MS-438 RL-098 RL-099 SW-567 SW-568 2-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description Ref. No. Part No. Description A-1764-316-A AF-129 FLEXIBLE BOARD, COMPLETE < COIL > * S007 1-786-914-31 SWITCH, TACTILE ****************************** * S008 1-786-914-31...
Page 20
3. ASSEMBLY Assembly-1: Precaution During of attachment Sheet (L). Assembly-2: Check the claw of the Ground Plate Assembly-3: Precaution During of attachment is completely caught. Filter Spacer and Optical Filter Block. Ground Plate Filter Spacer Claw Sticking standard Optical Filter Block Cutting portion Mountain fold Main Frame...
Page 21
4. BLOCK DIAGRAMS 4-1. OVERALL BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. CD-785 FLEXIBLE BOARD SY-255 BOARD LCD901 (LCD MODULE) CN702 LENS BLOCK CN301 V_OUT CCD_OUT CCD_OUT IC301...
Page 22
4-2. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-255 BOARD RL-099 RL-098 BOARD FLASH FLEXIBLE UNIT BOARD T101 CN704 CN201 CN705 D007 F001 L101 D102 ACV_UNREG ST_UNREG...
Page 24
6. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams For Printed Wiring Boards • All capacitors are in μF unless otherwise noted. pF : μ •...
Page 35
6-2. PRINTED WIRING BOARDS AF-129 FLEXIBLE BOARD LND001 BT-059 FLEXIBLE BOARD LND002 BT901 BATTERY TERMINAL BOARD LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 1-880-482- D001 Note: BT901 is not included in BT-059 flexible complete board. AF ILLUMINATOR/ SELF-TIMER/ D001 SMILE SHUTTER...
Page 36
Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions. 注意 電池の交換は, 正しく行わないと破裂する恐れがあります。 電池を交換する場合には必ず同じ型名の電池又は同等品と 交換してください。 使用済み電池は,取扱指示に従って処分してください。 SW-567 BOARD (SIDE A) SW-567 BOARD (SIDE B) MS-436 BOARD BT001 (LITHIUM RECHARGEABLE BATTERY) TH001...