Table of Contents
Advertisement
Quick Links
L-1619
Rev. B
11/98
IMPORTANT RECEIVING INSTRUCTIONS
Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at
once. Shipping damage is NOT covered by warranty. The carrier is responsible for all repair or replace-
ment costs resulting from damage in shipment.
SAFETY FIRST
Carefully plan your system by selecting components designed to perform the intended operation and
which will adequately perform with existing equipment. Always check the product limitations regarding
pressure ranges, load capacities and set-up requirements. The system operating pressure must not
exceed the pressure rating of the lowest rated component in the system.
WARNINGS, AND INSTRUCTIONS included with, or attached to, each product. Follow all safety precau-
tions to avoid personal injury or property damage during system operation. ENERPAC CANNOT BE
RESPONSIBLE FOR DAMAGE OR INJURY RESULTING FROM UNSAFE USE OF PRODUCT, LACK
OF MAINTENANCE OR INCORRECT PRODUCT AND SYSTEM APPLICATION.
RED LENS
GREEN LENS
®
AUTO-COUPLER CONTROL BOX
PRODUCTION AUTOMATION
OFF
MAN
AUTO
AUTO-COUPLER
RET
ADV
AUTO-COUPLER
CYCLE START
Instruction Sheet
ACCB - 1
EMERG STOP
FIXTURE
UNCLAMP
CLAMP
FIXTURE
CYCLE START
Read all CAUTIONS,
GREEN LENS
RED LENS
Advertisement
Table of Contents
Related Manuals for Enerpac ACCB-1
Summary of Contents for Enerpac ACCB-1
- Page 1 WARNINGS, AND INSTRUCTIONS included with, or attached to, each product. Follow all safety precau- tions to avoid personal injury or property damage during system operation. ENERPAC CANNOT BE RESPONSIBLE FOR DAMAGE OR INJURY RESULTING FROM UNSAFE USE OF PRODUCT, LACK OF MAINTENANCE OR INCORRECT PRODUCT AND SYSTEM APPLICATION.
-
Page 2: Product Description
OPERATION Starting the system 1. Turn the ‘MAN OFF AUTO” key switch to “OFF” prior to powering up the ACCB-1 Control Box. This will prevent inadvertent start-up of the automatic or manual operating sequence. 2. Pull out the “EMERG. STOP” button. - Page 3 Auto-Coupler Control Box 10. After an additional 3 second delay to ensure depressurization of the lines, the pump will start and the auto-coupler will retract. The “AUTO-COUPLER RET” red pilot light flashes during retraction. 11. As the auto-coupler retracts to disengage the fixture, the “AUTO-COUPLER ADV” green pilot light and the “FIXTURE CLAMP”...
- Page 4 Auto-Coupler Control Box...
- Page 5 Auto-Coupler Control Box...
-
Page 6: Wiring Chart
Auto-Coupler Control Box WIRING CHART WIRE WIRE WIRE WIRING INTERCONNECTIONS NUMBER COLOR GUAGE TERM# LOCATION TERM# LOCATION CUSTOMER COMMON CUSTOMER -------- -------- SPARE (ENERGIZED WHEN A FIXTURE IS SENSED) -------- -------- SPARE (ENERGIZED WHEN A FIXTURE IS SENSED) SPARE -------- -------- -------- CR2 N.C. -
Page 7: Specifications
Auto-Coupler Control Box SPECIFICATIONS PRODUCTION AUTOMATION EMERG STOP AUTO OPERATOR STATION SPECIFICATIONS HOFFMANN NEMA TYPE 12 RATING ELECTRICAL ENCLOSURE AUTO-COUPLER FIXTURE UNCLAMP CLAMP SIZE: 10.00 X 8.00 X 4.00 (254,0 X 203,2 X 101,6) PUSHBUTTONS: VOLTAGE RATING: 600 AC/DC MAX. AMPS MAX: 10 AUTO-COUPLER FIXTURE... - Page 8 Fax: 001 86 21 646 691 39 Fax: +34 1 661 47 89 All Enerpac products are guaranteed against defects in workmanship and materials for as long as you own them. Under this guarantee, free repair or replacement will be made to your satisfaction.
Need help?
Do you have a question about the ACCB-1 and is the answer not in the manual?
Questions and answers