1. INTRODUCTION Thanks for purchasing a DMXking product. Our aim is to bring you high quality products with great features we know you’ll appreciate. HARDWARE AND FIRMWARE VERSIONS From time-to-time minor hardware changes occur in our products usually small feature additions or unseen optimizations. The table below lists eDMX4 MAX DIN product variants.
Supported operating systems: Windows, MacOS, Linux, iOS, Android − eDMX1 MAX - 1x DMX512 Out or DMX512 In with Art-Net, sACN E1.31 and E1.20 RDM support − Art-Net broadcast, Art-Net II,3 & 4 unicast, sACN/E1.31 Multicast and sACN Unicast support −...
Protocol Protocol activity. Flash Yellow = Art-Net/sACN. Solid Yellow = Bootloader mode Link/Act Network activity. Green = Link, Flash = Traffic Port A – Front XLR DMX512 Port A TX/RX activity DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
Recall DMX Snapshot at startup Unchecked DMX512 Universe 1 [Net 00, Subnet 0, Universe 0-0] Note: sACN Universe 1 = Art-Net 00:0:0 *Global threshold for all DMX-IN ports, configured only in Port A settings tab. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
Art-Net port is unavailable. It is also possible to lock eDMX Configuration to the alternate port via the Advanced menu. Note that DMXking nodes are always listening on both primary and alternate ports so there is no device configuration required to change.
Network Adapter IP Address dropdown box and also ensure the subnet mask is appropriate. Settings Broadcast is suppored by eDMX MAX which allows node settings to be updated regardless of the network adapter subnet range. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
We do not recommend performing firmware updates over routed networks. Note only signed encrypted firmware files from DMXking.com can be successfully loaded to ensure you won’t brick your device by accident. Future firmware releases for this product will be in the form 0126-500-VersionMajor.VersionMinor.enc...
Page 10
When incoming DMX512 channel 1+N exceeds 512 to channels are ignored/lost. Make changes to the applicable Port settings then click Update. Changes on all port tabs are updated regardless of which tab the Update button is clicked. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
Note Art-Net II unicast is not supported meaning only Art-Net broadcast streams are displayed. The DMX Display utility works with any manufacturers Art-Net hardware and can be useful for diagnostics and simple testing of DMX512 fixtures. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
**NOTE YOU WILL CLEAR THE FIRMWARE HOLDING FACTORY RESET DURING POWER ON** eDMX Configuration Factory Reset (Legacy devices) menu is not relevant to eDMX MAX devices and will not have any effect. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
DMX Universe sACN 1-63999 which is translated to an Art-Net Port-Address (Net:Sub:Uni). Setting DMX Universe = 1 results in sACN Universe = 1 and Art-Net 00:0:0 (Universe 1 = Art-Net Universe DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
If Broadcast Threshold = 0 the frame is always broadcast on the IP subnet. If Broadcast Threshold > 0 and number of detected Art-Net II/3/4 devices "subscribed" to that universe is less than the threshold the frame is unicast to each device. DMXking.com • JPK Systems Limited • New Zealand 0132-700-4.1...
LED screens, fog machines and laser displays. The DMXking eDMX MAX unit is an Art-Net/sACN node designed for use with computer based show control software or expansion of lighting console outputs. It replaces an entire lighting console allowing the user to perform sophisticated shows with little more than a laptop.
This warranty covers any defects in materials or workmanship with the exceptions stated below. How long coverage lasts This warranty runs for two years from the date of shipment from an authorized DMXking distributor. What is not covered Failure due to operator error or incorrect application of product.
Need help?
Do you have a question about the eDMX1 MAX and is the answer not in the manual?
Questions and answers