Related Manuals for Bentone BF 1 FUV FAME
Summary of Contents for Bentone BF 1 FUV FAME
- Page 1 178 152 35-5 P93783 2022-10–14 Providing sustainable energy solutions worldwide Installation- and maintenance instruction BF 1 FUV FAME/RME LMO14.113C2E ANV47C Translation of the original instructions.
- Page 2 1~230V 1,0A 50Hz IP 20 Motor supply MADE IN SWEDEN BY 1. Manualer på övriga språk 1. Manuals in other languages 1. Manualer på andre sprog 2. www.bentone.com\ 2. www.bentone.com\ 2. www.bentone.com\ nedladdning eller scanna download or scan QR-code. download eller scan QR-koden.
-
Page 3: Table Of Contents
Inlet cone, air adjustment ............16 10. Log of flue gas analysis .............38 Air intake rotation ............... 17 Air duct ..................17 Electric equipment .............18 Safety system ................18 Wiring diagram ................19 Function LMO14/24 ..............20 Colour codes LMO14/24 ............21 Fault codes LMO14/24 ............... 21 Bentone... -
Page 4: General Information
Make sure that the burner is suitable for the application (see Technical • Data). All components must be installed without being bent, twisted or • subjected to mechanical or thermal forces that affect components. 165 105 01-2 2021-12-07 Bentone... - Page 5 When in operation, the burner’s noise level can exceed 85 dBA – use • hearing protection! - Operation: Carry out all stipulated settings, service and inspection work within • the set time. • If the oil burner control has a solid red light, contact your installer. Bentone...
-
Page 6: General Requirements Fame/Rme
Annual cleaning and checking for the presence of water in the tank • should be done to avoid corrosion and microorganisms. 165 405 06 2021-12-07 Bentone... -
Page 7: Technical Data
Fuel oil A Bio 10 according to DIN 51603-6. • Dimensions BF 1 FUV Protrusion from flange, Length of flame tube measurement B Flange 1 Flange 2 Dimensions, flanges 2.1.1 Flange 1 Flange 2 ø90 ø89,7 130–150 125–150 165 305 50-3 Bentone... -
Page 8: Model Bf 1 Fuv 63-16
Alt.2 The burner’s noise level can be reduced by connecting the burner’s air intake to the air duct that opens into an appropriate location. Installation must be done so it does not prevent air supply to the burner. Working area 1.3-4.6 kg/h 15-55 kW mbar Do not exceed the working area. -0,5 Bentone... -
Page 9: Basic Settings - Fuel Oil
When operating at high power or low air excess and HVO/XTL is used as fuel, the flame signal may deteriorate (blue flame), the signal lamp in the reset button flashes green. By lowering the air velocity or changing the flame detector to QRC1 A1, the flame signal can be improved. Bentone... -
Page 10: Nozzle And Pump Pressure
/s (cSt) at a density of 830 kg/m Burner with preheater Allow for a reduction in oil quantity of 5–20% with preheating owing to: Temperature increases at the nozzle. • Nozzle design. • Capacity (the higher the capacity the lower the difference). • Bentone... -
Page 11: Components
Nozzle assembly adjustment Ignition transformer Separating screw Flame tube Oil burner control Solenoid valve Electrical contact X1 (refer to wiring diagram) Oil pump Motor Air regulator Capacitor Air intake Preheater, where fitted Air flow indicator Ignition electrode Fan housing, rear Bentone... - Page 12 Bentone...
-
Page 13: Installation
(Refer to basic settings). Note that this only refers to the basic setting; the setting must be adjusted after the burner has been started. At this time flue gas analysis and soot measurement must be carried out. 165 305 18 Bentone... -
Page 14: Burner Installation
Disconnect the power at the main switch. Wire the Eurostecker X2 as in alt. 1–3 (refer to Electrical equipment). Connect the Eurostecker X2 to the burner. Switch on the power at the main switch. Bentone... -
Page 15: Settings
This provides the following nozzle according to the nozzle table, (see Technical data). Nozzle: 0.75 Gph 11.0 bar Pump pressure: Setting values for 33 kW according to basic setting diagram, (see Technical data). Air setting: 13.0 Insert setting: 165 305 19-2 Bentone... -
Page 16: Nozzle Assembly Adjustment
STD position to achieve good starts and operations. (A cast-in arrow on the fan housing indicates the position of the inlet cone. In addition to the scale on the inlet cone casting, there is also a mark (M) indicating the factory setting.) Bentone... -
Page 17: Air Intake Rotation
A hose connection air duct is available in three different dimensions: 48, 68, and 78 mm outer diameter (D). The air duct is installed on the air intake at the place where the grille is attached in the standard model Bentone... -
Page 18: Electric Equipment
The cables of the safety system must be separated so that the outgoing signal is not placed in the same cable as the incoming signal. 165 205 56-2 Bentone... -
Page 19: Wiring Diagram
Wiring diagram Alt 2 Alt 3 Alt 4 Alt. 1 Enl DIN 4791 Brown Blue Gn/Ye Ground/Yellow Black Grey Bentone... -
Page 20: Function Lmo14/24
< 1 s < 1 s Ambient temperature -5 - +60°C -20 - +60°C Min detector current required (with fl ame) 45 µA dc 45 µA dc Max perm. detector current (without fl ame) 5.5 µA dc 5.5 µA dc Bentone... -
Page 21: Colour Codes Lmo14/24
If the reset button is instead kept pressed a second time for at least 3 seconds, you can, via an interface, obtain the corresponding information on a computer or flue gas analyser. To return to normal operation: Press the reset button for 1 second. Bentone... -
Page 22: Pump Suntec Anv47C
Oil temperature: max. 60°C Components Nozzle connection G 1/8” Vacuum manometer connection G 1/8” Manometer connection G 1/8” Filter Suction line G 1/4” Metal plug G 1/4” Return plug Return line G 1/4” Pressure regulation 165 305 52 Bentone BF1... -
Page 23: Filter Replacement
Two-pipe system Conversion to two-pipe system Remove the metal plug (7) G ¼”, fi t the return plug (8) in the return line (9). Return plug are not included in products with one-pipe system, separately sold. Solenoid valve Bentone BF1... -
Page 24: Function Anv47C
At that same moment the nozzle line is closed. This provides a sharp cut-off. The on and off functions can be controlled independent of motor rpm, and react very quickly. When the solenoid valve is not activated torque is low up to full motor rpm. Bentone BF1... -
Page 25: Suction Pipe Tables Anv47C
The tables give the total suction line length in meters with a nozzle capacity of 2.1 kg/h. Max. permissible pressure on the suction and return lines is 2.0 bar. For a two-pipe system the Q 46 l/h pump capacity at 0 bar applies. Bentone BF1... -
Page 26: Preheater
If the oil temperature is low and the oil flow is high, the preheater thermostat may cut out. Because of this it is important that the burner control system has a circuit that maintains preheat. 165 205 57 Bentone... -
Page 27: Service
Ignition system with fl ame guard 10 years 250,000 cycles UV fl ame sensor 10,000 h Damper motor 500,000 cycles Contactor 10 years 500,000 cycles The burner and its components must be recycled according to applicable regulations. 165 405 08-2 2022-10-09 Bentone... -
Page 28: Service Positions
Suspend the fan housing by the fan housing service attachment on the screw used for joining the front piece to the fan housing, with the air intake upwards, as shown in the illustration to the left. 165 305 51-2 Bentone... -
Page 29: Combustion Assembly Service
Install the brake plate and electrode package. Check that the distance between the nozzle and brake plate is correct (refer to Technical data). Re-assemble the burner. Switch on the main power and open the fuel supply. Start burner and check/adjust combustion. When servicing/replacing components that affect combustion, flue gas analysis and soot test must be carried out following installation. Bentone... -
Page 30: Replacing The Oil Pump
Loosen the screws (4) and pull out the oil pump and solenoid valve as one assembly. Turn the valve forward and detach it from the pump. Reassemble in reverse order. Do not forget thread sealer between the pump and the elbow. (t.ex Loctite 5188, 5400) fi g 1 When servicing/replacing components that aff ect combustion, fl ue gas analysis and soot test must be carried out following installation. Bentone... -
Page 31: Fan Motor Replacement
Place the cable conduit entry and the photocell cable in position. Screw the electrical console in place. Connect the motor wiring. Join together the fan housing and the burner front piece. Switch on the main power and open the fuel supply. Start burner and check/adjust combustion. When servicing/replacing components that affect combustion, flue gas analysis and soot test must be carried out following installation. Bentone... -
Page 32: Air Intake And Intake Cone Service
Fit the O-ring in the groove between the fan housing and inlet cone. Ensure that it is properly located in the groove and is not damaged when the air intake is fitted. Switch on the main power and open the fuel supply. Start burner and check/adjust combustion. When servicing/replacing components that affect combustion, flue gas analysis and soot test must be carried out following installation. Bentone... -
Page 33: Fan Wheel Checks
Fit the O-ring in the groove between the fan housing and inlet cone. Ensure that it is properly located in the groove and is not damaged when the air intake is fitted. Switch on the main power and open the fuel supply. Start burner and check/adjust combustion. When servicing/replacing components that affect combustion, flue gas analysis and soot test must be carried out following installation. Bentone... - Page 34 Place the cable conduit entry and the photocell cable in position. Screw the electrical box in place. Connect the motor wiring. Join together the fan housing and the burner front piece. Switch on the main power and open the fuel supply. Start burner and check/adjust combustion. When servicing/replacing components that affect combustion, flue gas analysis and soot test must be carried out following installation. Bentone...
-
Page 35: Fault Location
Preheater temperature too low Check preheater function New oil type Adjust the preheater‘s set operating temperature Check that the oil used has the physical parameters that the burner is rated for. If not, change the oil. 165 105 09-2 2021-01-21 Bentone... -
Page 36: Delayed Ignition
Check that the oil used has the physical parameters that the burner is rated for. If not, change the oil. Temperature of the oil from the tank is too low, increase the temperature of oil from tank Clean the pump filter Bentone... -
Page 37: Pump Pressure
Change the oil or the pump‘s oil parameters Pump worn Replace the pump Pump run using impure oil that has worn the Replace pump and install self-cleaning pump out prematurely filter in the oil system Blocked pump filter Check, clean pump filter Bentone... -
Page 38: 10. Log Of Flue Gas Analysis
10. Log of flue gas analysis Tel. no: Owner Adresss Tel. no: Installation Boiler Type Make Power kW Burner Type Model Serial no. Fuel Step 1 Step 2 Step 3 Draught in fireplace Fan Press mbar Filter smoke number Flue gas temp. °C Setting brake disc Setting Air damper Pump pressure... - Page 39 EU Declaration of conformity Bentone Oil Burners Type: BF 1 ST 133 B 40 B 65 ST 108 ST 146 B 45 B 70 ST 120 B 30 B 55 B 80 This declaration of conformity is issued under the sole responsibility of the manufacturer.
- Page 40 UK Declaration of conformity Bentone Oil Burners Type: BF 1 ST 133 B 40 B 65 ST 108 ST 146 B 45 B 70 ST 120 B 30 B 55 B 80 This declaration of conformity is issued under the sole responsibility of the manufacturer.
- Page 44 Enertech AB. P.O Box 309, SE-341 26 Ljungby www.bentone.com...
Need help?
Do you have a question about the BF 1 FUV FAME and is the answer not in the manual?
Questions and answers