Advertisement
Fence
LOCK KNOB
1.
From
among
the loose parts find the following:
(1)
Fence
(1)
Fence
Face
(2)
Fence
Brackets
la\
Erin nA ann nunn+n
(2) Tilt
Indicators
(2)
Lock
Knobs
(4)
1/4"-20
x 3/4"
Hex
Cap
Screws
(4)
1/4
Lockwashers
(4) 9/32" ID
x
9/16" OD x 1/16" Thick
Washers
(2) 9/32" ID x 17/32" OD x 1/8" Thick
Washers
(10)
#8-32
x
1/2"
Flat
Head
Machine
Screws
(10) #8 Flat
Washers
(10) #8-32 Hex
Nuts
(2) #10-24 x 1/2" Pan Head Machine
Screws
(2)
#10 Flat
Washers
NOTE: USE
OF
WASHERS
LESS
THAN 1/8
THICK
MAY
RESULT
IN
FENCE
TIGHTENING
PROBLEMS
FENCE
SeGMENT
9/32
ID
X 17/32
OD
X 1/8
THK
WASHER
FENCE
\
fR
O\-=
+8-32 X 1/2
FLAT
HEAD MACHINE SCREW
FENCE_BRACKET
1/4-20 Xg/4
HEX
CAP
SCREW
TILT INDICATOR
9/16
OD
9
/
3
:
1
P/
f
6 THK
FLAT WASHER
+ IO FLAT
WAS
2. Attach fence
brackets
to
base
using 1/4"-20
x
3/4"
hex cap screws,
9/32"
ID
x 1/16" thick
washers
and 1/4" lockwashers, snug but do not tighten
+lO-24 X 1/2
PAN
HEAD
MACHINE SCREW
3. Attach
fence segments
to
fence
with six
#8-32
flat
head screws, #8
flat
washers. and #8-32 hex nuts.
4.
Attach
fence
face
to fence with four
#8-32
flat
head
screws,
#8
flat
washers, and #8-32 hex nuts.
5,
Place assembled
fence
on
machine with fence brackets
inside
the fence
segments,
6. Position lock knobs with 9/32" ID x
17/32"
OD x 1/8" thick
washers
through slots
in
fence segments and thread into fence
brackets
7. Place square against fence face and table surface. Bring fence square to
table and tighten lock
knobs,
8
THERE
MUST BE 1/32" TO 1/16" gap
between
the lower
edge
of
the
fence
and
jointer tables
(with
table
set
for 0" cut). To adjust,
move
fence
assembly by loosening the 1/4"-20 x 3/4"
hex cap
screws attaching
the
Tence
brackets to the
base.
Retighten
hex
cap screws after adjustment
has
been made
\R\\
9.
Recheck
squareness of
fence.
\\\
TILT INDICATOR
SHOULD
THE FENCE SEGMENT AT
BE LINED UP
WITH
THE a'
MARK
DO NOT OVER
TIGHTEN
10. install tilt indicators with #10-24 x 1/2"
pan head machine
screw
and #10
flat
washers. Set
0'' of indicators to 0''
of
segments
and
tighten
the
screw
11. The fence should now
be
adjusted and will accurately measure angles to
45'' inboard and 45'' outboard
(see
adjustments section)
Fence Extension
To aid
in edge
jointing of workpieces 4"
and wider,
you
may
extend
the
fence
height. The
extension can
be
constructed of
1
"
(3/4"
thick) stock pine
or
hardwood
The wooden fence face must
be
removed
so
the extension can
be mounted
using the fence face mounting
holes.
+8
FLATHEAD
OLNrFns
Use
#8 flat head wood
screws
of sufficient
length
to
securely attach
the
extension to the fence,
Make
sure that the
head
of
the
screws are below
the
surface
of the fence
so
as not to interfere with the
workpiece.
6
Advertisement
