Advertisement
A
SAFETY RULES FOR
JOINTER–PLANER
A
Safety
is
a combination of operator common sense and alertness
at
all times when the Jointer–Planer is
being
used.
Study these rules and general safety rules before operating and retain them for future use
1. WEAR EYE PROTECTION
9.
ALWAYS
- Use hold down/push blocks for jointing
material
narrower than 3", or planing material thinner than
3"
2.
NEVER MAKE
JOINTING OR PLANING CUT
DEEPER
THAN
1/8"–PER
PASS.
10. ALWAYS - Keep cutter sharp
3. FEED WORKPIECE AGAINST ROTATION OF CUTTER.
11.
NEVER
- Use
in an
explosive atmosphere. Normal sparking
of
motor may ignite
fumes
4. KEEP
FINGERS
AWAY FROM
REVOLVING CUTTER–use
fixtures when necessary.
12, OUTDOOR
EXTENSION
CORD
USE
- When tool
is
used out-
doors,
use
only extension cords suitable for use
outdoors
Outdoor approved
cords are
marked
with the suffix
W-A,
for
example, SJTW-A or SJOW-A.
5. NEVER
PERFORM
JOINTING OR PLANING
OPERATION
WITH CUTTER HEAD GUARD
REMOVED.
6.
NEVER FORCE
CUTTING ACTION. Stalling or partial stalling
of
motor can cause major damage. Allow motor to reach full
speed before cutting.
13. ALWAYS
use
identical replacement
parts
when
servicing.
14. This tool
is
intended
for
RESIDENTIAL USE
ONLY.
7.
NEVER
-
Attempt
to
perform
an
abnormal
or little
used
opera-
tion without study and the use of
adequate holddown/push
blocks, jigs, fixtures,
stops,
etc.
WARNING: DO NOT ALLOW FAMILIARITY (GAINED
FROM
FREQUENT
USE
OF
YOUR JOINTER–PLANER) TO
BECOME
COMMONPLACE. ALWAYS REMEMBER THAT A CARELESS
FRACTION OF
A SECOND
IS
SUFFICIENT TO INFLICT
SEVERE
INJURY
8.
NEVER
- Attempt to
cut
small
pieces.
Depth
of Cut
Hand
Knob
ASSEMBLY
1. Find
one
3/8" lockwasher and
the
depth of cut hand knob from the parts
bag
3/8
HEX
NUT
2. Turn the nut
on
the height adjustment
screw
until five full threads
extend
beyond the
nut,
3. Place
lockwasher
on height adjustment screw and thread hand
knob
onto
screw.
1/
re
rEPTH
OF
HAND
KN
4. Back nut up against hub of hand knob. Tighten with
14mm
ar
9/16"
wrench while holding hand knob.
Chip Deflector
1. Loosen the screw in the center of vacuum port of chip
discharge.
RETIGHTEN
THIS
SCREW
LOOSEN AND
2. Install
Slot
of chip deflector
between
the chip
discharge
and the
flat
washer and
retighten
CAUTION: THE CHIP DEFLECTOR MUST BE IN PLACE FOR SAFE
OPERATION.
FAILURE
TO INSTALL THE CHIP
DEFLECTOR MAY
RESULT
IN PERSONAL
INJURY.
A
T
CHIP
DEFLECTOR
Vacuum
Hose
Adapter
1. Turn jointer
upside
down
on
clean
work
surface
and push
vacuum
hose
adapter into opening in rear
cover,
2. Align the screw holes on the rear cover and vacuum hose adapter. Install
#8 x
3/8
type B
self
tapping
screw and tighten
CAUTION: THE VACUUM
HOSE
ADAPTER MUST BE IN PLACE
FOR SAFE OPERATION. FAILURE TO INSTALL THE ADAPTER
MAY RESULT IN PERSONAL
INJURY
A
Cutter Guard Assembly
1. Place
the
slot on the cutter guard
assembly
over the tab on the
front
cover as shown and align the shoulder bolt with the threaded
hole.
SHOULDER
BOLT
_B<\ccw
SLOTS
TAB
CUTTERGUARD
a
2. Rotate the cutter guard counterclockwise until the tab is under the cutter
guard
and
tighten the shoulder bolt. Be sure the cutter guard
rotates
freely
after
tightening
the
shoulder
bolt,
CAUTION: THE CUTTER
GUARD
MUST BE IN
PLACE FOR SAFE
OPERATION.
FAILURE
TO INSTALL THE CUTTER
GUARD
CAN
RESULT
IN SERIOUS
INJURY
A
5
Advertisement
