HPE FlexNetwork 6604 Installation Manual
  1. Manuals
  2. Brands
  3. HPE Manuals
  4. Network Router
  5. FlexNetwork 6604
  6. Installation manual

HPE FlexNetwork 6604 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HPE FlexNetwork 6604/6608 Routers
Installation Guide
Part number: 5998-1521s
Document version: 6W104-20160520

Advertisement

Table of Contents
loading

Related Manuals for HPE FlexNetwork 6604

Summary of Contents for HPE FlexNetwork 6604

  • Page 1 HPE FlexNetwork 6604/6608 Routers Installation Guide Part number: 5998-1521s Document version: 6W104-20160520...
  • Page 2 © Copyright 2015, 2016 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Contents Preparing for installation ················································································· 1 Safety recommendations ··································································································································· 1 Installation site requirements ····················································································································· 1 Ventilation and cooling ······························································································································· 2 Rack-mounting requirements ····················································································································· 2 Installation accessories ······································································································································ 3 Pre-installation checklist ···································································································································· 4 Installing the router ························································································· 6 Installation flow ·················································································································································· 6 Check before installation ····································································································································...
  • Page 4 Displaying fan status ································································································································ 39 Displaying status of power supplies ········································································································· 39 Displaying temperature alarm thresholds ································································································· 39 Port configuration and management ················································································································ 40 Configuring a combo interface ················································································································· 40 Displaying transceiver module information and alarm information ··························································· 41 Active and standby MPU switchover ················································································································ 42 Responding to system faults ····························································································································...
  • Page 5 Interface module, cable, and connection failure ······························································································ 70 Software upgrade failures ································································································································ 70 TFTP upgrade failure ······························································································································· 70 FTP upgrade failure ································································································································· 71 Application file missing errors ·························································································································· 71 Document conventions and icons ································································· 72 Conventions ····················································································································································· 72 Network topology icons ···································································································································· 73 Support and other resources ········································································...
  • Page 6 Appendix D Arranging slots and numbering interfaces ······························· 122 Slot arrangement ··········································································································································· 122 Slot arrangement for MPUs and interface modules ······················································································· 124 Numbering interfaces ····································································································································· 124 Examples ······················································································································································· 125 Example 1 ·············································································································································· 125 Example 2 ·············································································································································· 125 Appendix E Cables ····················································································· 126 Ethernet twisted pair cable ·····························································································································...

  • Page 7: Preparing For Installation

    Preparing for installation This chapter discusses preparation for installing 6604 and 6608 routers. Safety recommendations WARNING! Read all of the safety instructions in the Compliance and Safety Guide supplied with your device before installation and operation. This section provides general recommendations. For more information see the Compliance and Safety Guide included with your device.

  • Page 8: Ventilation And Cooling

    Table 4 Dust concentration limit in the equipment room Substance Concentration limit (particles/m ≤ 3 x 10 Dust particles (No visible dust on desk in three days) NOTE: Dust particle diameter ≥ 5 µm Table 5 Limits on harmful gases in the equipment room Maximum concentration (mg/m 0.06 0.05...

  • Page 9: Installation Accessories

    • As a best practice, mount a device in an open rack. If you mount a device in a closed rack, make sure there is a good heat dissipation system. • Install the router in a rack that has rack shelves. •...

  • Page 10: Pre-Installation Checklist

    NOTE: Figures in Table 6 are for illustration only. Pre-installation checklist Table 7 Pre-installation checklist Item Requirements Result • There is a minimum clearance of 10 cm (3.9 in) around the inlet and exhaust vents for heat dissipation of the router chassis. Ventilation •...
  • Page 11 Item Requirements Result • The rack is sturdy enough to support the weight of the router and installation accessories. • The size of the rack is appropriate for the router. • The front and rear of the rack are at least 0.8 m (31.50 in) away from walls or other devices.

  • Page 12: Installing The Router

    Installing the router CAUTION: Do not use the rear cover handle when you move the router chassis. This handle is designed to help you remove the rear cover and cannot support the chassis weight. IMPORTANT: Keep the packaging from your router and its accessories for future use. Installation flow Figure 2 6604/6608 router installation flow Start...

  • Page 13: Check Before Installation

    Check before installation To prepare for installing the router: • Make sure you have read "Preparing for installation" carefully and that the installation site meets all the requirements. • Prepare a 19-inch rack. For more information about how to install a rack, see the installation guide provided with the rack.

  • Page 14: Installing The Cable Management Brackets

    Figure 4 Installing cage nuts Installing the cable management brackets As shown in Figure 5, before installing a mounting bracket to the router, install the cable management bracket to the left mounting bracket with screws. Figure 5 Installing the cable management bracket (1) Left mounting bracket (2) Cable management bracket Installing an air filter...
  • Page 15 To install an air filter: Position the upper slide rail horizontally near the top of the left side of the chassis, as shown Figure 6. Fasten the screws with a Philips screwdriver. Figure 6 Installing the air filter slide rails Position the lower slide rail horizontally near the bottom of the left side of the chassis, as shown in Figure...

  • Page 16: Installing The Mounting Brackets To The Router

    Installing the mounting brackets to the router Before installing the router to a rack, install the mounting brackets to the sides of the router. As shown in Figure 9, align the screw holes of the mounting brackets with the screw holes on sides of the router chassis.

  • Page 17: Grounding The Router

    Figure 10 Fastening the router to the rack Grounding the router WARNING! Correctly connecting the router grounding cable is crucial to lightning and EMI protection. If at all possible, use the grounding cable provided with the router. To connect the grounding cable: Remove the grounding screw from the rear panel of the router chassis.

  • Page 18: Installing An Mpu

    Figure 11 Connecting the grounding cable to the grounding hole of router Installing an MPU The RPE-X1 MPU ,the RSE-X1 and the MCP-X1/X2 MPU are both hot-swappable. Installing an RPE-X1 MPU The RPE-X1 MPU is hot swappable. To install an RPE-X1: Locate the slot to install the RPE-X1.
  • Page 19 As shown in Figure 13, gently push the RPE-X1 carrier (with the components facing up) into slot 1 along the slide rails, until the positioning pins on the backplane are seated in the positioning holes at the bottom of the RPE-X1 carrier. Figure 13 Installing the RPE-X1 carrier Push the ejector levers inward to lock the RPE-X1 carrier in position, and fasten the captive screws on the ejector levers.

  • Page 20: Installing An Rse-X1 Mpu

    Installing an RSE-X1 MPU The RSE-X1 MPU is hot swappable. To install an RSE-X1: Locate the slot to install the RSE-X1. It can be installed in either slot 1 or slot 2. The figures illustrate installing an RPE-X1 to slot 1. Use a Phillips screwdriver to remove the captive screws on the filler panel.

  • Page 21: Installing A Fip Module

    Figure 16 Inserting the MCP-X1 into the slot Fasten the captive screws with a Philips screwdriver. If the router is powered off, power it on. After the MCP-X1/X2 is powered on, the RUN LED (green) flashes fast (at 8 Hz). It flashes slowly (at 1 Hz) after the MCP-X1/X2 application is loaded.

  • Page 22: Installing A Sap/Oap

    Figure 17 Inserting a FIP module If the router is powered off, power it on. After the FIP module is powered on, the RUN LED (green) flashes once and then flashes fast (at 8 Hz). It flashes slowly (at 1 Hz) after the application is loaded. This means that the FIP module runs correctly.

  • Page 23: Installing A Him

    Figure 18 Inserting a SAP module Fasten the captive screws on the SAP module with a Philips screwdriver. Power on the router. After the SAP module is powered on, the RUN LED (green) flashes once and then flashes fast (at 8 Hz).

  • Page 24: Installing A Mim

    Figure 19 Installing a HIM Use a flat-blade screwdriver to fasten the captive screws on the HIM. Power on the router. Check the status LED on the front panel. On means the HIM is installed correctly and running correctly. Off means the HIM has failed the POST. Installing a MIM MIMs are hot swappable.

  • Page 25: Installing A Fan Tray

    Figure 20 Pushing the MIM into the slot Use a flat-blade screwdriver to fasten the captive screws on the MIM. Power on the router and check the status LED on the front panel. On means the MIM is installed correctly and running correctly. Off means the MIM has failed the POST.

  • Page 26: Installing A Cf Card

    On means the fan tray is operating correctly. Off means the fan tray has failed the POST. For the LED description of the fan tray, see "Appendix C LEDs." Installing a CF card To install a CF card: To install a CF card on MCP-X1/X2, press the spring clip at the right of the CF card cover to open it, skip this step if you install a CF card on RPE-X1/RSE-X1.

  • Page 27: Connecting A Power Cord

    Connecting a power cord Make sure the router is reliably grounded before connecting a power cord. After connecting the power cord, power on the power supply. If the power supply LED is green, the power supply works correctly. If the LED is red, the power supply has failed. Connecting an AC power cord To connect an AC power cord: Make sure the router is reliably grounded, and the power switch on the router is in the OFF...

  • Page 28: Connecting Ethernet Cables

    Figure 25 Connecting the DC power cord Put the protection cover on the wiring terminals. Connect the other ends of the wires to the DC power source wiring terminals, with the negative wire (– or L–) to the negative terminal (–) and the positive wire (+ or M/N) to the positive terminal (+).
  • Page 29 • Never bend or curve a fiber when connecting it. As shown in Figure 26, the bend radius must be not less than 10 cm (3.94 in). Figure 26 Bend radius of the fiber • Ensure the cleanness of the fiber ends. •...
  • Page 30 Install the transceiver module, as shown in Figure Figure 28 Installing the transceiver module Remove the dust cover on the transceiver module and the protective caps on the LC connectors. Plug the LC connectors on one end of the fiber cable into the Rx and Tx ports of the router, as shown in Figure Figure 29 Connecting the fiber connectors...

  • Page 31: Logging In To The Router And Configuring Basic Settings

    Logging in to the router and configuring basic settings Before powering on the router, connect and configure a terminal or PC to act as the console terminal. After powering on the router, use the console terminal to configure additional ways to log Logging in through the console port You can log in only through the console port the first time you log in to your router.

  • Page 32: Setting Terminal Parameters

    Figure 30 Connecting the console cable Setting terminal parameters To configure and manage the router, you must run a terminal emulator program on the configuration terminal, for example, a PC. This section uses Windows XP HyperTerminal as an example. To set terminal parameters on a terminal using Windows XP HyperTerminal: Select Start >...
  • Page 33 Figure 31 Connection description of the HyperTerminal Type the name of the new connection in the Name text box and click OK. The following dialog box appears. Select the serial port to be used from the Connect using drop-down list, as shown in Figure Figure 32 Setting the serial port used by the HyperTerminal connection...
  • Page 34 Figure 33 Setting the serial port parameters Click OK after setting the serial port parameters and the system enters the following interface. Figure 34 HyperTerminal window Click Properties in the HyperTerminal window to enter the aaa Properties dialog box. Click the Settings tab, set the emulation to VT100, and then click OK., as shown in Figure...

  • Page 35: Powering On The Router

    Figure 35 Setting terminal emulation in aaa Properties dialog box Powering on the router Verifying before power-on Before powering on the router, verify the following items: • The power cord and grounding cable are connected correctly. • The power source voltage meets the requirement of the router. •...

  • Page 36: Displaying Boot Information

    System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Press Ctrl+T to start memory test Booting Normal Extend BootWare..**************************************************************************** HPE A6600 Router BootWare, Version 1.15 **************************************************************************** Copyright (c) 2010-2015 Hewlett Packard Enterprise Development LP Compiled Date : Nov 6 2015...

  • Page 37: Logging In To The Router Through Telnet

    ..................................The main application file is self-decompressing......................................................................................................................................................................................................................................................Done! System application is starting... Starting application at 0x00010000 ... Mainboard 1 is master. User interface con0 is available. Press ENTER to get started.

  • Page 38: Configuring Basic Settings

    Step Command Enter AUX user interface view user-interface aux 0 Set the authentication mode authentication-mode none Set the user privilege level user privilege level 3 To connect a terminal or PC to the AUX port: Plug the DB-9 female connector to the serial port of the configuration terminal or PC. Connect the RJ-45 connector to the AUX port of the router.

  • Page 39: Hardware Management And Maintenance

    Comware Software, Version 5.20.106, Release 3303P23 Copyright (c) 2010-2015 Hewlett Packard Enterprise Development LP HPE A6608 uptime is 0 week, 0 day, 1 hour, 59 minutes Slot 1: RSE-X1 uptime is 0 week, 0 day, 1 hour, 59 minutes CPU type: RMI XLS408 1000MHz...
  • Page 40 Please wait... Save succeeded. Execute the more aa.diag command in user view, and then press the Page Up and Page Down keys to view the contents of the file aa.diag. • To display the operational statistics of each functional module of the router, type n when the system prompts you to save or display the diagnostic information.
  • Page 41 43141 DFWD 290ca DRVH 20f80 DRVL 10fab DIBD 1d4a SOCK e7ad ADJ4 498ba SFLW fd46 1613f 576d LAGG 8b52 MSTP 7204 GARP 437e6 5c081 RRPP 16291 LLDP 62fc DLDP 17bf6 SMLK 86e9 662d1 2218cb NTPT 8243 VTYD 45622 62755 3f61 8fa6db 31f3c 20adb...

  • Page 42: Displaying Module Information

    Additional detailed output is omitted. Displaying module information Use the display device verbose command to display detailed information for the modules in all slots. <Sysname> display device verbose System-mode(Current/After Reboot): Normal/Normal Slot No. Board type Status Primary SubSlots --------------------------------------------------------------------- Absent RSE-X1 Normal Master...

  • Page 43: Displaying Cpu Usage

    VENDOR_NAME:HPE Slot 3: DEVICE_NAME:HP 6600 FIP-20 Flex Intf Pltfm Rtr Mod JG358A DEVICE_SERIAL_NUMBER:CN5AFS1123 MAC_ADDRESS:NONE MANUFACTURING_DATE:2015-10-8 VENDOR_NAME:HPE Use the display device manuinfo slot slot-number command to display the electrical label information for the module in a specified slot. <Sysname> display device manuinfo slot 1...

  • Page 44: Displaying Memory Usage

    Field Description seconds). Average CPU usage in the last minute (after the router boots, the router 1% in last 1 minute calculates and records the average usage at the interval of one minute). Average CPU usage in the last five minutes (after the router boots, the 1% in last 5 minutes router calculates and records the average usage at the interval of five minutes).

  • Page 45: Displaying Fan Status

    Displaying fan status Use the display fan command to display the operational status of the built-in fan. <Sysname> display fan 1 State: Normal Table 13 Output description Field Description Number of the fan. The fan state: • Normal—The fan is operating correctly. State •...

  • Page 46: Port Configuration And Management

    information of your router Available in any view Port configuration and management This section discusses configuring and managing combo interfaces and transceiver modules. Configuring a combo interface A combo interface is a logical interface comprising an SFP port of a transceiver module and an RJ- 45 Ethernet port.

  • Page 47: Displaying Transceiver Module Information And Alarm Information

    The Maximum Transmit Unit is 1500 Internet protocol processing : disabled IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 7425-8acc-7c0d IPv6 Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 7425-8acc-7c09 Media type is twisted pair, loopback not set, promiscuous mode not set 1000M, Full, link type is force link Output flow-control is disabled, input flow-control is disabled Last clearing of counters: Never Last 300 seconds input rate 381.90 bytes/sec, 3048 bits/sec, 2.98 packets/sec...

  • Page 48: Active And Standby Mpu Switchover

    Displaying transceiver interface information To identify transceiver modules, you can use the display transceiver interface command, which displays key parameters including transceiver module type, connector type, central wavelength of the laser sent, transmission distance, and vendor name or name of the vendor who customized the transceiver modules.

  • Page 49: Responding To System Faults

    The standby MPU becomes an active MPU, and the former active MPU automatically reboots and becomes a standby MPU. When the standby MPU is started, the active MPU performs initial synchronization for the standby MPU. During the synchronization process, if you press Enter on the configuration terminal, the system prompts that you cannot execute any command on the active MPU or standby MPU.

  • Page 50: Rebooting A Module Or Router

    You can save the router's current configuration in one of the following methods: • Fast saving: Executing the save command without the safely keyword. This mode saves the file more quickly but is likely to lose the existing configuration file if the router reboots or the power fails during the process.
  • Page 51 • (Avoid when possible) Power on the router after powering it off, which is also called hard reboot or cold start. Hard reboots should be avoided because powering off a running router causes data loss and hardware damages. To reboot the router immediately: Task Command Remarks...

  • Page 52: Replacement Procedures

    Replacement procedures The routers use a modular, all-pluggable design, and support replacing hot swappable modules without interrupting router operation. Safety recommendations Always wear an ESD wrist strap or ESD gloves when replacing the modules. When operating a pluggable module, such as a the MPU, RPE-X1 carrier (used when you use an RPE-X1 MPU), FIP module, SAP module, memory module, CF card, or HIM/MIM, note the following guidelines: Ensure good alignment with the slot to avoid damage to the module during installation or...

  • Page 53: Replacing An Rpe-X1 Mpu

    Switch off the power supply to be removed, and then remove it. (See Replacing a power supply.) Make sure the new power supply is switched off before installing it. Install the new power supply. (See Installing a power supply.) Power on the newly-installed power supply. Replacing an RPE-X1 MPU Prerequisites •...

  • Page 54: Replacing An Rse-X1 Mpu

    Replacing an RSE-X1 MPU Prerequisites • If the router is configured with only one MPU, make sure all power sources to the router are turned off before replacing the MPU. • If the router is configured with two MPUs, make sure both MPUs operate correctly before replacing any MPU.

  • Page 55: Replacing A Fip Module

    Holding the ejector levers of the MCP-X1 with both hands, pull the ejector levers outward, and gently pull the MCP-X1 out of the slot along the slide rails. Figure 39 Pulling the MCP-X1 out of the slot If you do not install a new MPU in the slot, install a blank panel. To install a new MPU, see “Installing an MPU.”...

  • Page 56: Replacing A Sap/Oap Module

    Figure 40 Pulling the FIP module out of the slot If you do not install a new FIP module in the slot, install a blank panel. To install a new FIP module, see "Installing a FIP module." Replacing a SAP/OAP module CAUTION: When the RUN LED of the SAP/OAP module is flashing fast, do not unplug the module.

  • Page 57: Replacing A Him

    Figure 41 Pulling the SAP module out of the slot If you do not install a new SAP module in the slot, install a blank panel. To install a new SAP module, see "Installing a SAP/OAP." Replacing a HIM To replace a HIM: Determine the HIM to be removed.

  • Page 58: Replacing A Mim

    Replacing a MIM To replace a MIM: If the MIM is configured with settings before being pulled out of the FIP module, the settings for the MIM will not automatically restore if you plug the MIM into the FIP module after rebooting the FIP module.

  • Page 59: Replacing A Transceiver Module

    Figure 44 Pressing the eject button As shown in Figure 45, press the eject button again to eject the CF card part-way out of the CF card reader. Figure 45 Pressing the eject button a again to eject the CF card Pull the CF card out of the CF card reader and put it in an antistatic bag.

  • Page 60: Replacing A Fan Tray

    Figure 46 Removing a transceiver module Insert the plastic plug into the removed transceiver module, and put the transceiver module into its original shipping materials. If you do not install a new transceiver module in the interface, install a dust-proof plug in the interface.

  • Page 61: Replacing An Air Filter

    Figure 47 Pulling out the fan tray Store the removed fan tray in an antistatic bag. Install a new fan tray. For more information, see "Installing a fan tray." For information about fan tray LED status, see "Appendix C LEDs." Replacing an air filter CAUTION: You can clean the air filter with water, but wait until it is completely dry before installing it again.

  • Page 62: Replacing A Memory Module

    Figure 49 Pulling the air filter out along the slide rails Install a new air filter. For more information, see "Installing an air filter." Replacing a memory module CAUTION: Before replacing a memory module, contact Hewlett Packard Enterprise Support for permission. Otherwise, Hewlett Packard Enterprise shall not be liable for any consequence caused thereby.

  • Page 63: Memory Module Structure

    Figure 50 Memory module replacement flowchart Memory module structure Figure 51 Memory module structure(DDR2) (1) Connector edge (2) Polarization notch (3) Latch notch...

  • Page 64: Memory Module Slot

    Figure 52 Memory module structure (DDR3) (1) Connector edge (2) Polarization notch (3) Latch notch Memory module slot Figure 53 Memory module slot (1) Release latch (2) Memory module slot Replacing a memory module CAUTION: Do not touch the surface-mounted components of the memory module directly with your hands, to avoid damaging the memory module.
  • Page 65 Figure 54 Removing the old memory module Align the polarization notch of the new memory module with the key in the connector. As shown in Figure a. Insert the new memory module into the slot. b. Carefully and firmly press the new memory module at both ends until you hear a click. This indicates the memory module is seated in the memory module slot.

  • Page 66: Troubleshooting

    Troubleshooting The barcode on the router chassis contains product and service information. Before you return a faulty router for service, provide the router's barcode information to Hewlett Packard Enterprise service. MPU failures The MPU LEDs provide information on the status of the MPU. Table 16 MPU LEDs Status Description...

  • Page 67: Alm Led Is Steady On Or Flashes

    For example, the ALM LED is on when the system is over-temperature. In this case, the system displays the following output: %Jun 25 14:38:45:444 2010 HPE DRVMSG/3/TempCritical: CPU temperature critical in Slot 3, index is 1. To solve the problem, check the output (such as the system temperature and PCB voltage alarms) on the serial terminal and the software management tool.

  • Page 68: Power Supply Failures

    Fan tray is absent After the router is booted, the following information may appear on the configuration terminal: %Jul 5 14:47:20:618 2010 HPE DEV/4/FAN ABSENT: Fan 1 is absent. The output indicates that the fan tray is not in position.

  • Page 69: Alm Led Is Red

    5 14:59:03:878 2010 HPE DRVMSG/3/FanPlugIn:Fan 1 Plug In. %Jul 5 14:59:03:879 2010 HPE DRVMSG/3/FanErr:Fan 1 Error. #Jul 5 14:59:03:998 2010 HPE DEV/1/FAN STATE CHANGES TO FAILURE: Trap 1.3.6.1.4.1.2011.2.23.1.12.1.6<fanfailure>: fan ID is 1 %Jul 5 14:59:03:998 2010 HPE DEV/4/FAN FAILED: Fan 1 failed.

  • Page 70: Garbled Terminal Display

    Are the terminal properties set correctly? The correct console terminal settings are: set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, Flow control to None, and Terminal Emulation to VT100. Is there a problem with the console cable? If the cause cannot be located in the steps above and the problem persists, contact Hewlett Packard Enterprise Support.

  • Page 71: Examining The State Of Password Recovery Capability

    System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Press Ctrl+T to start memory test Booting Normal Extend BootWare..**************************************************************************** HPE A6600 Router BootWare, Version 1.15 **************************************************************************** Copyright (c) 2010-2015 Hewlett Packard Enterprise Development LP Compiled Date : Nov 6 2015...
  • Page 72 EXTEND CPLD Version : 2.0 PCB Version : Ver.B BootWare Validating... Backup Extend BootWare is newer than Normal Extend BootWare,Update? [Y/N] Press Ctrl+B to enter extended boot menu... Press Ctrl + B within three seconds after the "Press Ctrl+B to enter extended boot menu..." prompt message appears.

  • Page 73: Dealing With User Privilege Level Password Loss When Password Recovery Capability Is Enabled

    ============================================================================ Ctrl+Z: Access EXTEND-ASSISTANT MENU Ctrl+F: Format File System Enter your choice(0-9): 6 After the configuration skipping flag is set successfully, the following message appears: Flag Set Success. When the EXTEND-BOOTWARE menu appears again, enter 0 to reboot the router. The router starts up with empty configuration.

  • Page 74: Dealing With Password Loss When Password Recovery Capability Is Disabled

    Ctrl+F: Format File System Enter your choice(0-9): 8 The router deletes the user privilege level password configuration commands from the main next-startup configuration file. After the operation is completed, the following message appears: Clear Application Password Success! When the EXTEND-BOOTWARE menu appears again, enter 0 to reboot the router. The router starts up with the main next-startup configuration file.

  • Page 75: Cooling System Failure

    %May 14 21:37:35:271 2010 HPE DRVMSG/3/Temp2High: Environment temperature too high in Slot 0, index is 2. #May 14 21:37:35:713 2010 HPE DEV/1/BOARD TEMPERATURE UPPER: Trap 1.3.6.1.4.1.2011.2.23.1.12.1.16<hwBoaardTemperatureHigher>: frame Index is 0, slot Index 0.0 %May 14 21:37:35:713 2010 HPE DEV/4/BOARD TEMP TOOHIGH: Board temperature is too high on Frame 0 Slot 0, type is MPU.

  • Page 76: Interface Module, Cable, And Connection Failure

    To troubleshoot a cooling system failure: Check whether the fans are running correctly. Check whether the working environment of the router is well ventilated. Use the display environment command to check whether the temperature in the router keeps rising. If the temperature inside the router exceeds 90°C (194°F) a.

  • Page 77: Ftp Upgrade Failure

    FTP upgrade failure Start the router, and upgrade the software through FTP. The following problems may occur: The CF card does not have enough space available. 227 Entering Passive Mode (192,168,1,10,10,204) 150 "xxx" file ready to send (xxx bytes) in ASCII mode FTP: Error Writing Local File(Screen).

  • Page 78: Document Conventions And Icons

    Document conventions and icons Conventions This section describes the conventions used in the documentation. Port numbering in examples The port numbers in this document are for illustration only and might be unavailable on your device. Command conventions Convention Description Bold text represents commands and keywords that you enter literally as shown. Boldface Italic text represents arguments that you replace with actual values.

  • Page 79: Network Topology Icons

    Network topology icons Convention Description Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.

  • Page 80: Support And Other Resources

    Support and other resources Accessing Hewlett Packard Enterprise Support • For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website: www.hpe.com/assistance • To access documentation and support services, go to the Hewlett Packard Enterprise Support Center website: www.hpe.com/support/hpesc Information to collect •...

  • Page 81: Websites

    For more information and device support details, go to the following website: www.hpe.com/info/insightremotesupport/docs Documentation feedback Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title,...
  • Page 82 part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page.

  • Page 83: Appendix A Chassis Views And Technical Specifications

    H3C SR6608 IMPORTANT: For regulatory identification purposes, each HPE 6600 router is assigned a regulatory model number (RMN). These regulatory numbers should not be confused with the marketing name HPE 6600, or product codes. Table 18 MPU models Product code...

  • Page 84: Chassis Views

    RT-SAP-24GBP Aggregation Platform Module Table 20 Power supply models Product code Description Alias JC492A HPE FlexNetwork 6616 650W AC Router Power Supply PSR650-A JC493A HPE FlexNetwork 6616 650W DC Router Power Supply PSR650-D Table 21 Fan tray models Product code...
  • Page 85 Figure 58 Front view (an RSE-X1 MPU installed) (1) MPU slot (slot 1) (2) MPU/service module slot (3) Service module slot (slot 2 to slot 3) (4) Power supply slots (5) PoE module slot (reserved) (6) Fan tray NOTE: • In this figure, one RSE-X1 MPU is installed. You can install one more RSE-X1 MPU or install one service module in the MPU/service module slot.
  • Page 86 Figure 60 Front view (an MCP-X2 installed) (1) MPU slot (slot 1) (2) Service module slot (slot 2 to slot 3) (3) Power supply slots (4) Fan tray Figure 61 Rear view (1) Rear cover handle (2) Air vents (3) Chassis handle (4) Air filter (optional) CAUTION: Do not use the rear cover handle when you move the router chassis.

  • Page 87: 6608 Router Chassis Views

    6608 router chassis views Figure 62 Front view (an RPE-X1 carrier installed) (1) MPU slot (slot 0 to slot 1) (2) Service module slots (slot 2 to slot 5) (3) Fan tray (4) Power supply slots (5) PoE module slot (reserved) NOTE: •...
  • Page 88 Figure 63 Front view (an RSE-X1 MPU installed) (1) MPU slot (slot 1) (2) MPU/service module slot (slot 2) (3) Service module slot (slot 3 to slot 5) (4) Power supply slots (5) PoE module slot (reserved) (6) Fan tray NOTE: •...
  • Page 89 (3) Power supply slots (4) Fan tray Figure 65 Front view (an MCP-X2 installed) (1) MPU slot (slot 1) (2) Service module slots (slots 2 through 5) (3) Power supply slots (4) Fan tray Figure 66 Rear view (1) Rear cover handle (2) Air vents (3) Chassis handle (4) Air filter (optional)

  • Page 90: Dimensions And Weight

    CAUTION: Do not use the rear cover handle when you move the router chassis. This handle is designed to help you remove the rear cover and cannot support the chassis weight. Dimensions and weight Table 22 Dimensions and weight Specification Item 6604 6608...

  • Page 91: Rse-X1

    (11) USB 1 LED (12) CF card LED (13) CF card (14) CF card button Table 23 RPE-X1 specifications Item Specification DDR2 SDRAM Memory type and size 1 GB (default, one memory module) 2 GB (maximum, two memory modules) NVRAM 128 KB Console port 9600 bps (default) to 115200 bps...

  • Page 92: Mcp-X1/X2

    (11) AUX port (AUX) (12) Active/Standby LED (ACT) (13) Power alarm LED (PALM) (14) RUN LED (15) System alarm LED (ALM) Table 24 RSE-X1 specifications Item Specification DDR2 SDRAM • 2 GB (default, two memory modules) Memory type and size •...
  • Page 93 Figure 70 MCP-X2 (1) Combo interface 1 (2) Combo interface 3 (3) CF card slot (CF CARD) (4) CF card LED (CF) (5) Management Ethernet port (MANAGEMENT) (6) Console port (CONSOLE) (7) AUX port (AUX) (8) Reset button (RESET) (9) MCP-X2 status LED (10) USB port (11) 10 Gbps Ethernet port (12) Combo interface 2...

  • Page 94: Components

    Components CF card CAUTION: • Use CF cards provided by Hewlett Packard Enterprise only. The router may be incompatible with other CF cards. • CF cards less than 256 MB are not supported. A CF card stores logs, system software image files, and configuration files. The RPE-X1/RSE-X1 are equipped with a built-in 256 MB CF card, and the MCP-X1/X2 are equipped with a built-in 1 GB CF card, which is identified with cfa0.
  • Page 95 Connects the serial port of a remote PC through a pair of modems to establish a dial- Services up connection with the PC Management Ethernet port The management Ethernet port is a 10Base-T/100Base-TX/1000Base-T RJ-45 port. It allows you to upgrade software and manage the router through a network management server without using any service interface of the router.
  • Page 96 Table 31 Transceiver modules for the SFP ports Max. Product Central Description Connector Optical fiber transmission code wavelength distance HPE X110 100M SFP 62.5/125 µm multi- 2 km (1.24 JD102B 1310 nm LC FX mode optical fiber miles) Transceiver HPE X110...
  • Page 97 HPE X110 80 km 100M SFP 9/125 µm single-mode JD091A 1550 nm LC LH80 optical fiber (49.71 miles) Transceiver HPE X120 0.55 km 1G SFP LC 62.5/125 µm multi- JD118B 850 nm mode optical fiber (0.34 miles) Transceiver HPE X120...

  • Page 98: Flexible Interface Platform Modules

    Central Max. Connect Product code Description wavelengt Fiber type transmission or type distance HPE X130 10G 50/125 µm multi- JD092B SFP+ LC SR 850 nm 300 m (984.25 ft) mode Transceiver HPE X130 10G 9/125 µm single- 10 km (6.21...
  • Page 99 Table 34 References for FIP operations Operation Reference Install and remove the FIP "Installing a FIP module" and "Replacing a FIP module." Install and remove MIMs “Installing a MIM” and “Replacing a MIM.” Connect network cables "Connecting a copper Ethernet port"...
  • Page 100 Table 39 Transceiver modules for the SFP ports Central Max. Descriptio Connecto Product code wavelengt Optical fiber transmission distance HPE X120 62.5/125 µm 1G SFP LC 0.55 km (0.34 JD118B 850 nm multi-mode miles) optical fiber Transceiver 9/125 µm...
  • Page 101 Central Max. Descriptio Connecto Product code wavelengt Optical fiber transmission distance Transceiver • 1310 HPE X120 9/125 µm 10 km 1G SFP LC JD098B single-mode • BX 10-U (6.21 miles) optical fiber Transceiver 1490 • 1490 HPE X120 9/125 µm...
  • Page 102 Figure 73 FIP-20 front panel (1) Slot 2 (2) Slot 1 (3) Status LED (4) OPEN BOOK mark The OPEN BOOK mark indicates that the operator must read the following sections before working with the FIP: Table 41 References for FIP operations Operation Reference Install and remove the FIP...
  • Page 103 FIP-210 You can plug up to two HIMs into the FIP-210 to provide high-speed service processing or plug up to two MIMs into the FIP to provide high-density narrowband aggregation. The FIP-210 also supports the mix of a HIM and a MIM. Figure 74 FIP-210 front panel (1) Combo interface 1 (2) Combo interface 0...
  • Page 104 Item Specification Hot swapping Supported “Hot-swapping” a module refers to removing and/or installing a module without powering off the router. To hot swap a module: Removing a module a. Use the remove slot slot-number command to stop the module. b. Remove the module. Installing a module: Install the new module into the slot without powering off the router.

  • Page 105: Service Aggregation Platform Modules

    Item Specification 10/100 Mbps, half/full-duplex 1000 Mbps, full-duplex • A fiber port, 1000 Mbps, full-duplex 4 supported 2 full-height or 4 half-height HIMs supported (Half-height HIMs include HIM-4G4P, HIM-TS8P, and HIM-8GBP-V2) Hardware encryption Supported Hot swapping Supported Combo interface specifications Specifications of combo interfaces on the FIP-240 and the FIP-110 are the same.

  • Page 106: Rt-Sap-24Gbp

    Item Specification NVRAM 128 KB Max power consumption 200 W Connector type RJ-45 Number of interfaces Interface standards 802.3, 802.3u, and 802.3ab Interface type Automatic MDI/MDIX Cable type Straight-through/crossover Ethernet cable Transmission distance 100 m (328.08 ft) Ethernet_II Supported frame format Ethernet_SNAP 10 Mbps Full/half duplex, auto-negotiation...
  • Page 107 Table 49 Transceiver modules for the SFP ports Max. Product Central Description Connector Optical fiber transmission code wavelength distance HPE X120 1G Category 5 or above 100 m (328.08 JD089B SFP RJ45 T RJ-45 twisted pair cables Transceiver HPE X110 62.5/125 µm multi- 2 km (1.24...

  • Page 108: Oap Cards

    For the OAP cards available for the routers and their compatibility, see "Appendix B Hardware compatibility matrixes." For more information about the OAP cards, see the HPE FlexNetwork 6600/HSR6600/HSR6800 Router Series Interface Module Guide . HIMs and MIMs You can install HIMs to provide 10-Gbps service processing capability and install MIMs to provide high-density narrowband aggregation.

  • Page 109: System Power

    System power The 6604 and 6608 routers can be DC-powered or AC-powered. You can install two power supplies in your router, and they must be the same model. Table 50 System power specifications Item Specification AC powered—100 VAC to 240 VAC; 50 Hz or 60 Hz Rated voltage range DC powered—–60 VDC to –48 VDC AC powered—10 A...

  • Page 110: Dc Power Supply

    Table 51 AC power supply specifications Item Specification Rated voltage range 100 VAC to 240 VAC; 50 Hz or 60 Hz Maximum input current 10 A Maximum power 650 W Dimensions (H × W × D) 40 × 140 × 350 mm (1.57 × 5.51 × 13.78 in) DC power supply The DC input voltage range is –48 VDC to –60 VDC.

  • Page 111: Fan Trays

    Fan trays Figure 80 6604 fan tray (1) Fan tray status LED (RUN) (2) Alarm LED (ALM) (3) Fans (4) Handle Figure 81 6608 fan tray (1) Fan tray status LED (RUN) (2) Alarm LED (ALM) (3) Handle (4) Fans Table 53 Fan tray specifications Specification Fan (built-in)
  • Page 112 Specification Fan (built-in) 6604 6608 Dimensions (H × W × 136.4 × 31 × 427.8 mm (5.37 ×1.22 × 228 × 31 × 413.3 mm (8.98 ×1.22 × 16.84 in) 16.27 in) Failsafe Supported Hot swapping Supported...

  • Page 113: Appendix B Hardware Compatibility Matrixes

    Appendix B Hardware compatibility matrixes In the compatibility matrixes, "√" means "Supported" and "×" means "Not supported." FIP and router compatibility matrix Table 54 FIP and router compatibility matrix 6604 6608 FIP-10 √ √ FIP-110 √ √ FIP-20 √ √ FIP-210 √...

  • Page 114: Interface Module And Fip Compatibility Matrix

    Interface modules 6604 6608 RT-HIM-4GBP √ √ RT-HIM-8GBP √ √ RT-HIM-1EXP √ √ RT-HIM-CL1P √ √ RT-HIM-CL2P √ √ RT-HIM-MSP2P √ √ RT-HIM-MSP4P √ √ RT-HIM-PS1P √ √ RT-HIM-RS2P √ √ SAPs RT-SAP-48GBE √ √ RT-SAP-24GBP √ √ OAPs RT-SPE-FWM-200 √...
  • Page 115 10/100/100 100/1000 1000 0 Mbps Mbps Gbps Mbps Mbps Mbps fiber-to- Gbps fiber Interface fiber fiber fiber copper fiber fiber transc modules transcei transcei transcei conversio transcei transcei eiver n SFP modul module module module copper module module module RT-MIM-8T1- ×...

  • Page 116: Sap/Oap And Mpu Compatibility Matrix

    SAP/OAP and MPU compatibility matrix Table 59 SAP/OAP and MPU compatibility matrix RPE-X1 RSE-X1 MCP-X1 MCP-X2 SAP/OAP × × × SAP-48GBE √ × × × SAP-24GBP √ × × SPE-FWM-200 √ √ × × SPE-SSL-200 √ √ Appendix C LEDs 6604 and 6608 routers provide MPU LEDs, FIP LEDs, and power supply LEDs to indicate the operating status of MPUs, FIPs, and power supplies.

  • Page 117: Mpu Leds

    Remarks 10/100/1000 Mbps copper Ethernet port LEDs (GE0 through GE3) CF card LED (CF) Run LED (RUN) Active LED (ACT) MCP-X2 LEDs Power management alarm LED (PALM) Table Alarm LED (ALM) Management Ethernet port LED (LINK/ACT) 10 Gbps Ethernet port LED (SFP+LINK/ACT) 1000 Mbps fiber Ethernet port LED (SFP0 through SFP3) Run LED (RUN)
  • Page 118 Status Description otherwise the RPE-X1 may be damaged). The RPE-X1 is in the standby state. Active LED of the RPE- The RPE-X1 is in the active state. (green) The system is operating correctly and there is no alarm. A fault has occurred to the system or the available power is insufficient.
  • Page 119 Table 62 RSE-X1 LED description Status Description No CF card is present or the CF card is not recognizable. CF card LED A CF card is in position and has been detected. (green) The system is accessing the CF card. In this state, do Flashing not remove the CF card.
  • Page 120 Figure 84 LEDs on the MCP-X1 Table 63 MCP-X1 LED description Status Description The corresponding interface is not connected. Steady green A 1000 Mbps link is present. Data is being received or transmitted at a rate of GE0 through Flashing green 1000 Mbps.
  • Page 121 Status Description Steady green A 1000 Mbps link is present. Steady yellow A 10/100 Mbps link is present. No data is being received or transmitted. ACT LED Flashing yellow Data is being received or transmitted. No link is present. Steady green A 1000 Mbps link is present.
  • Page 122 Status Description No power input is available, or the MCP-X2 has failed. Slow flashing The MCP-X2 is operating correctly. (1 Hz) Run LED (green) The application software is being loaded (in this Fast flashing case, never power off the device or hot-swap the (8 Hz) MCP-X2;...

  • Page 123: Fip Leds

    FIP LEDs Figure 86 FIP-10 LED Figure 87 FIP-20 LED Table 65 FIP-10/20 LED description Status Description No link is present or the FIP is faulty. Slow flashing (1 Hz) The FIP is operating correctly. Application software is being loaded (in this case, (green) Fast flashing (8 Hz) never power off the device or hot-swap the FIP;...
  • Page 124 Figure 89 FIP-210 LEDs Figure 90 FIP-240 LEDs Table 66 FIP LED description Status Description No link is present. Solid green A 1000 Mbps link is present. 10/100/1000 Data is being received or transmitted at a rate of Flashing green Mbps copper 1000 Mbps.

  • Page 125: Sap Leds

    SAP LEDs Figure 91 SAP LEDs Table 67 RT-SAP-48GBE LED description Item Status Description No link is present. Solid green A 1000 Mbps link is present. Data is being received or transmitted at a rate of Flashing green Status LEDs 1000 Mbps.

  • Page 126: Him/Mim Leds

    Data is being received or transmitted at a rate of 100 Flashing yellow Mbps. HIM/MIM LEDs For description of HIM/MIM LEDs, see the HPE FlexNetwork 6600/HSR6600/HSR6800 Router Series Interface Module Guide . Power supply LEDs Figure 93 AC power supply LED...

  • Page 127: Fan Tray Leds

    Fan tray LEDs Figure 95 Fan tray of the 6604 Figure 96 Fan tray of the 6608 Table 70 Fan tray LED description Status Description The system is powered off or the fan tray is faulty. Run LED The fan tray is operating correctly. (green) The fan tray is operating correctly.

  • Page 128: Appendix D Arranging Slots And Numbering Interfaces

    Appendix D Arranging slots and numbering interfaces Slot arrangement The router provides many types of interfaces, such as console, AUX, GigabitEthernet, serial (synchronous), and POS ports. This chapter describes how these interfaces are numbered. Figure 97 Slot arrangement on the 6604 configured with an RPE-X1 Figure 98 Slot arrangement on the 6604 configured with an RSE-X1 or MCP-X1/X2...
  • Page 129 Figure 99 Slot arrangement on the 6608 configured with an RPE-X1 Figure 100 Slot arrangement on the 6608 configured with an RSE-X1 or MCP-X1/X2 NOTE: • The numbers in Figure 97 through Figure 100 represent corresponding slot numbers. • On a router configured with an RSE-X1, slots are numbered from slot 1 instead of slot 0. •...

  • Page 130: Slot Arrangement For Mpus And Interface Modules

    Slot arrangement for MPUs and interface modules Table 71 Slot arrangement for MPUs and interface modules Slot arrangement on the Slot arrangement on the MPUs and interface modules 6604 6608 RPE-X1 (supporting 1+1 Slot 0 and slot 1 Slot 0 and slot 1 redundancy) RSE-X1 (supporting 1+1 Slot 1 and slot 2...

  • Page 131: Examples

    Examples Example 1 A FIP-110 is installed in slot 3. Fixed GigabitEthernet interfaces on the FIP-110 • GigabitEthernet 3/0/0 • GigabitEthernet 3/0/1 Example 2 A FIP-210 is installed in slot 3 and a RT-HIM-4GBE module is installed on the FIP-210. Fixed GigabitEthernet interfaces on the FIP-210 •...

  • Page 132: Appendix E Cables

    Appendix E Cables The 6604 and 6608 support various types of MPUs and interface modules. The port types vary by the MPU and interface module model. Use dedicated cables to connect the ports of different types. Table 72 Cables Cable Applicable port type Description Connects the RJ-45 Ethernet port of the...
  • Page 133 Figure 101 RJ-45 connector pinout EIA/TIA cabling specifications define two standards, 568A and 568B, for cable pinouts. • Standard 568A—pin 1: white/green stripe, pin 2: green solid, pin 3: white/orange stripe, pin 4: blue solid, pin 5: white/blue stripe, pin 6: orange solid, pin 7: white/brown stripe, pin 8: brown solid.
  • Page 134 Figure 103 Crossover cable Select an Ethernet twisted pair cable according to the RJ-45 Ethernet port type on your device. An RJ-45 Ethernet port can be MDI (for routers and PCs) or MDIX (for switches). Table 74 Table show their pinouts. Table 74 RJ-45 MDI port pinouts 10Base-T/100Base-TX 1000Base-T...

  • Page 135: Making An Ethernet Twisted Pair Cable

    When you use a fiber port, you need an SFP, XFP, or SFP+ transceiver module and a fiber cable with an LC connector. For the compatibility between the cards and transceiver modules, see HPE FlexNetwork 6600/HSR6600/HSR6800 Router Series Interface Module Guide.
  • Page 136 Table 76 Characteristics of single mode and multi-mode optical fibers Single mode fiber Multi-mode fiber Larger core than single mode fiber (50 Core Small core (10 micrometers or less) micrometers, 62.5 micrometers or greater). Allows greater dispersion and therefore, Dispersion Less dispersion signal loss exists.

  • Page 137: T1 Interface Cable

    T1 interface cable CAUTION: • When connecting the interface cable, pay attention to the mark on the interface to avoid wrong insertion, which may damage the interface module or even the host. • As a best practice to protect outdoor 8T1 cables against lightning strikes, install a special lightning arrester at the input end of the cables.

  • Page 138: Index

    MPU RESET button, basic settings, air filter (replacing), combo interface, alarm (displaying information), router, altitude, Telnet, architecture connecting HPE 6604 Router, AC power cord, router, AUX port, AUX port console cable, configuring and connecting, copper Ethernet port, specifications, DC power cord,...
  • Page 139 HIM replacement, LED, HIM/MIM LED, replacing, HPE 6604 Router architecture, specifications, HPE 6604 Router front and rear views, fault handling methods (choosing), HPE 6608 Router architecture, HPE 6608 Router front and rear views, failure troubleshooting, installation flow, LED, interface module/router compatibility,...
  • Page 140 power supply installation, fan tray, power supply LED, FIP module, power supply replacement, HIM, power supply specifications, installation flow, rack-mounting requirements, MIM, RESET button, MPU, power supply, router 19-inch rack installation, router installation, router, router slot arrangement, router (19-inch rack), RPE-X1 MPU hot swap, RPE-X1MPU, RPE-X1 MPU installation,...
  • Page 141 troubleshooting, connecting DC power cord, module connecting power cord, displaying information, power supply HIM, displaying status, MIM, hot swap, OAP card, installing, LED, slot arrangement, replacing, active and standby switchover, power system failure (troubleshooting), powering on router, components, failure troubleshooting, fault handling methods (choosing), rack (installing router), FIP compatibility,...
  • Page 142 FIP LED, installing, FIP module, replacing, FIP-110, RT-SAP-24GBP specifications, FIP-210, RT-SAP-48GBE specifications, HIM/MIM LED, HPE 6604 Router front and rear views, HPE 6608 Router front and rear views, safety recommendations management Ethernet port, installation, MPU components, maintenance, MPU LED, power supply,...
  • Page 143 (cooling system failure), power system failure, software upgrade failure, 70, terminal, TFTP software upgrade failure, TFTP upgrade failure, verifying electrical after power-on, electrical before power-on, views (front and rear) HPE 6604 Router router, HPE 6608 Router, MPU, VT100,...

This manual is also suitable for:

Flexnetwork 6608

Table of Contents