Advertisement
Quick Links
INSTALLATION MANUAL
To Qualifi ed Installer in Installation Work and Service
Air purifi er kit
(For 4-Way cassette type)
Model: TCB-EAPC1UHP-E
Observe the safety precautions described in the Operation Manual of the
Air purifi er kit, Installation Manual of the 4-way cassette type air conditioner
(indoor unit), or the Installation Manual supplied with the ceiling panel.
COMPONENTS
Part Name
Main frame
Dust collector
Deodorize fi lter
Wireless receiver
and Dust sensor
Remote controller
Remote controller holder
INSTALLATION DIAGRAM OF AIR PURIFIER KIT
Q'ty
Part Name
Battery
Actuator
1
Flat head wood screw
(Ø3.1×16L [mm])
Earth screw
1
Screw
(Ø4×10L [mm])
Screw
2
(Ø3×8L [mm])
Cord clamp
(Ø5.9 mm)
1
Cord clamp
(Ø4.4 mm)
Operation Manual
1
Installation Manual
(This Manual)
1
CD-ROM
Indoor unit
Ionizer brush
(Assembled into the Main frame)
Main frame
Deodorize fi lter
(Attach to the Main frame)
Wireless receiver unit
Ceiling panel
Dust collector
Actuator
(Install on the Air fi lter)
Air fi lter
Air inlet grille
• Thank you for purchasing Air purifi er kit for TOSHIBA air conditioners.
• Read this manual carefully for correct installation of the Air purifi er kit
before starting work.
• After the installation is completed, execute a test run to check for
normal operation and explain how to use and maintain the Air purifi er
kit to the customer according to the Operation Manual.
Ask the customer to keep this manual with the Operation Manual.
PREPARATION
Indoor unit preparation
To make screw holes of indoor unit are empty for the installation of the Air purifi er
kit.
So, some parts and current screws need to be disassembled.
Q'ty
2
CAUTION
• Be sure to stop operation of the air conditioner before work and then turn off
1
switch of the breaker.
• Wear heavy work gloves during the installation work to avoid injury.
2
1
1.
Remove the fan guard or cover sensor from indoor unit (depended on each
model) follow position as below.
7
• In case remove the fan guard
2
1
1
1
1
Fan guard
1
• In case remove the cover sensor
2.
Remove screw that fi xed the bell mouth with indoor unit 1 pc. as position
below.
Note:
• After remove this screw, please keep it for fi x the Air purifi er kit with indoor unit
for this position.
- 1 -
Fan guard
Screw 4 pcs.
Cover sensor
Cover sensor
Screw 1 pc.
Indoor unit
Bell mouth
Remove Screw 1 pc.
Indoor unit
Indoor unit
1-EN
Advertisement
Related Manuals for Toshiba TCB-EAPC1UHP-E
Summary of Contents for Toshiba TCB-EAPC1UHP-E
- Page 1 INSTALLATION MANUAL • Thank you for purchasing Air purifi er kit for TOSHIBA air conditioners. • Read this manual carefully for correct installation of the Air purifi er kit To Qualifi ed Installer in Installation Work and Service before starting work.
- Page 2 HOW TO INSTALL THE MAIN FRAME HOW TO INSTALL THE WIRELESS RECEIVER Separate the Dust collector from the Main frame. ※ Install the Wireless receiver in correct orientation, since the Wireless receiver can be installed at only one corner as shown in (Fig. 1). •...
- Page 3 Attach the Wireless receiver unit to the panel. At this time, be careful not to Pass the Wireless receiver lead wire from the ceiling panel through the claws pinch the wiring. (Fig. 4) If there is a part where the claws of the Wireless of the Main frame then wiring it to the electrical control box of indoor unit receiver part are not fi...
- Page 4 Attach the Air inlet grille to the Panel. At this time, be careful orientation of the HOW TO INSTALL THE DEODORIZE FILTER actuator must be match with the sensor position on the Main frame. The Deodorize fi lters are included as an accessory, attach them into specifi ed position of the Main frame when required.
-
Page 5: Operation Procedure
RBC-AMS5*E* RBC-ASCU11* Perform the advanced settings for the air conditioner. Carry out the setting operation while the indoor unit is stopped. (Turn off the air conditioning unit before starting the setting operation.) Display example of Field setting menu(2/2) RBC-AMSU51-ES 6.Setting timer operation mode 7.DN setting 8.Reset power consumption data Indoor unit No. -
Page 6: Installing The Remote Controller Holder
FAN CONTROL SETUP REMOTE CONTROLLER ADDRESS (A-B SELECTION) SETTING The high ceiling setting is necessary to change the setup value to High ceiling (3) when installing Air purifi er kit. • When two or more Wireless receiver are installed in a room, a unique address can be set for each Wireless receiver unit to prevent interference. -
Page 7: Maintenance And Cleaning
Notes on installing Remote controller SELF-DIAGNOSIS FUNCTION AND MEASURES • When using a Wireless remote controller in the remote controller holder on • The following table shows a few examples. For details of indoor unit errors, a wall, turn on a fl uorescent light and operate the Remote controller at the refer to the Installation Manual of the indoor unit. - Page 8 HOW TO DISASSEMBLE THE AIR FILTER HOW TO DISASSEMBLE THE DUST COLLECTOR FILTER Open the air inlet grille Push hook of Main frame at handle position to unlock the Dust collector as below. • Push the corner of the air inlet grille and then slide the two hooks toward inside while pushing its corner, hold the air inlet grille and open it quietly.