Related Manuals for MTI 526
Summary of Contents for MTI 526
- Page 1 Installation and Operation Manual MTI 526, 527P/S, & 527W Podiatry Chairs 527 P/S 527W...
-
Page 3: Table Of Contents
READ THIS MANUAL BEFORE INSTALLATION! ..............................2 Unpacking ..............................................3 Leveling Feet Adjustements......................................5 Upholstery Installation ........................................5 CONTROLS & FEATURES ..................................7 526 Pedestal Base Chair .........................................7 527S Model Chairs ..........................................7 527P Model Chairs ..........................................7 527W Model Chair ..........................................7 ASPECTS OF FOOT CONTROLS ................................7 OPERATION ........................................ -
Page 5: General Information
Installation and Operation Manual MTI 526, 527P/S, & 527W GENERAL INFORMATION Purpose of this Manual This manual covers the instructions for the installation and safe operation of these power exam and procedure tables. It is intended that it be used by the person(s) installing the equipment and by the medical professionals using it. -
Page 6: Transportation And Storage Conditions
Installation and Operation Manual | MTI 526, 527P/S, & 527W GENERAL INFORMATION Transportation and Storage Conditions CONTINUED Temperature Range: 0°C (32°F) to 44°C (110°F) Indicates Class 1, Type B, Medical Equipment Relative Humidity: Indicates the proper shipping orientation for 10° to 90° (non-condensing) the product. -
Page 7: Unpacking
Installation and Operation Manual | MTI 526, 527P/S, & 527W installation location is on a vinyl or hard tile floor, a piece Unpacking of carpet or other material should be placed beside the You will need the following to unpack and assemble pallet to act as a cushion to protect the flooring. - Page 8 Installation and Operation Manual | MTI 526, 527P/S, & 527W Be extremely careful in this next step of installing the arm linkage pin, that you do not drop the pin or e-ring inside the base or you will have to disassemble the covers to retrieve them.
-
Page 9: Leveling Feet Adjustements
Installation and Operation Manual | MTI 526, 527P/S, & 527W Each MTI chair has a circuit board. The included surge protector must be used to protect the board. Warranty is void if this surge protector is not used. Do not use a two-three plug adapter to plug the MTI chair into a two conductor outlet, as grounding reliability is not then maintained. - Page 10 Installation and Operation Manual | MTI 526, 527P/S, & 527W (2) Upholstered arms that come with (8) 10-24 x 1 1/2” screws and (8) #10 internal star washers Back/seat cushion flap If your MTI table is ordered with optional arms, headrests, lights, etc., those parts will be in a separate box...
-
Page 11: Controls & Features
Back down pedal/button – when pressed the back section lowers. The MTI chairs are available in a 2 or 3 power function. The two power Model 526 chair has power tilt and Tilt up pedal/button – when pressed the chair top tilts back up and down functions. -
Page 12: Operation
Installation and Operation Manual | MTI 526, 527P/S, & 527W OPERATION If the chair is unplugged, press the auto return and bring the chair back into the full home position before using programmability. Your new MTI chair is equipped with extremely high... -
Page 13: Model 527P & 527Wp "Programmable" Power Base Chair
Installation and Operation Manual | MTI 526, 527P/S, & 527W Model 527P & 527WP “Programmable” When chair is in motion from a programmable Power Base Chair position or auto return, injury may occur if chair is not attended to until it comes to a complete stop. -
Page 14: Swivel Base Operation
Installation and Operation Manual | MTI 526, 527P/S, & 527W Foot Section Adjustment The foot section on your new MTI chair was designed to allow for almost infinite adjustability over the nearly 12 inches of its extension. This adjustment is controlled by a lever with the black ball knob located at the front of the foot section on either side (Figure 18). -
Page 15: Debris Tray Tension Adjustment
Installation and Operation Manual | MTI 526, 527P/S, & 527W Retractable Arms Always return the foot section to the “closed” position BEFORE allowing the patient to exit the chair to avoid To Retract Arms grasp the black tab lever lock with possible injury to patient or damage to the chair. -
Page 16: Cleaning & Disinfection
Installation and Operation Manual | MTI 526, 527P/S, & 527W CLEANING & DISINFECTION Plastic Components Any plastic component such as the chair back cover or base cover should be cleaned regularly with a quality Upholstery grade of plastic cleaner and a soft cloth or a damp The upholstery used to cover your new MTI chair is cloth with mild soap. -
Page 17: 527W Ownership
Installation and Operation Manual | MTI 526, 527P/S, & 527W and backward, pull the fuse tray out of the bottom (4) 3/8” shoulder bolts of the receptacle to expose the two fuses. See the (8) 3/8” lock washers Specifications section for the exact replacement fuse parameters (Figure 21). - Page 18 Installation and Operation Manual | MTI 526, 527P/S, & 527W Figure 26 Figure 24 3. As seen in Figure 22, the left arm weldment (patient’s left) is on the lift side and the right (patient’s right) is on the right side. With both...
-
Page 19: Specifications
Installation and Operation Manual | MTI 526, 527P/S, & 527W SPECIFICATIONS Patient Weight (Maximum) 650 lbs (295.45 kg) Weight of Table Model 527, 326 lbs (148.2 kg) w/o accessories (Including upholstery kit and foot control) Model 527W, 390 lbs (176.9 kg) w/o accessories Model 526, 276 lbs (125.5 kg) w/o accessories... -
Page 20: Accessories
Installation and Operation Manual | MTI 526, 527P/S, & 527W ACCESSORIES Programmable Foot FC3-NS2PRS-LBT Use – to automatically position table to a preset Control FC3-SB2PRS-LBT position. Swivel Base Option Use – to provide rotation of the table top Restrictions – do not rotate table to short side of base and try to either exit or enter table. -
Page 21: Limited Warranty
(12) months from the date of shipment to the customer. MTI will, at its option, provide parts to the customer or repair the defective part at MTI’s factory or authorized repair facility. Except as it may... - Page 22 Notes...
- Page 23 Notes...
- Page 24 3655 West Ninigret Drive Salt Lake City, Utah, 84104 Fax 801-952-0548 www.mti.net © 2010 MTI, Inc. All rights reserved. MTI reserves the right to make any product changes without notice. DCN 073059 Rev A...
Need help?
Do you have a question about the 526 and is the answer not in the manual?
Questions and answers