Flamerite Fires E-FX 1000 Installation, Precautions & Servicing
Electric fire (fan heater)
Hide thumbs
Also See for E-FX 1000:
- Installation, precautions & servicing (21 pages) ,
- Installation, precautions & servicing (9 pages)
Related Manuals for Flamerite Fires E-FX 1000
Summary of Contents for Flamerite Fires E-FX 1000
- Page 1 Installation, Precautions & Servicing This product is only suitable for well insulated spaces or occasional use 1000 1300 1500 1800 www.e-fxfires.com...
- Page 2 Important Carefully remove the fire from the packing checking neither the heater nor the power cable has been damaged during transport. Do not operate the fire if damaged. Please bear in mind the weight of the fire before removal from the packaging and installation. Consider if help is required.
- Page 3 Important Safety Information and Warnings • WARNING: In order to avoid overheating, do not cover the heater. • For indoor use only. • Do not use the fire in the vicinity of a bath, shower or swimming pool. • Never use the fire to dry laundry. •...
- Page 4 BS-EN 55014-1:2017 BS-EN 55014-2:2015 BS-EN61000-3-2:2014 BS-EN 61000-3-3:2013 Manufactured by: Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs. WS13 7AU. UK Technical Specification A 230V 13A 50Hz supply is required. Maximum power consumption: 1500 Watts A 1.8 metre lead with a BS1363 plug containing a BS1362 13A fuse is supplied. Only use a BS1362 13A fuse with this appliance.
- Page 5 Installation Instructions WARNING: DO NOT TWIST, FORCE OR SQUEEZE THE FIRE DURING THE INSTALLATION PROCESS. There must be enough clearance for the fire to comfortably fit inside or against a wall. DO NOT SQUEEZE INTO AN OPENING as this may deform the case and stop the glass from moving correctly. The fire must be well supported in or on any structure.
- Page 6 Contemporary legs, the height you will need to fit the table below. Product Standard Contemporary Legs Plinth E-FX 1000 230mm 255mm E-FX 1300 230mm 255mm Take the following steps securing your fire firmly into position and onto a wall. Both top and lower fixing brackets come already attached to the fire.
- Page 7 Top Bracket Fixings 1000 1300 1500 1800 60mm screws M10 rawl plugs 13mm screws A second person will be required. For now, leave the top bracket attached. Place and hold the fire on the lower bracket and refit the bolts and washers through the slots back into the fire. Keeping the fire firmly pushed against the wall, mark across the length of the top bracket and into the slots above each hole.
- Page 8 Before any further work is completed now your fire is secure, make sure the mains cable is tightly fitted underneath the fire. Non Refective Rear Screen Option As standard one of the two rear screens in the fire has a reflective coating to mirror the log effect. When the fire is on, the flame simulates a 3 dimensional burn between the actual log effect and the refection generated by the coating.
- Page 9 You will need to carefully remove both screens, to do this unscrew the top bracket holding them in place. Using the foam tape provided in the accessory pack, apply across the length of the top bracket’s front face to keep the projection screen secure now the reflective glass screen has been removed. Screw the top bracket back into place and add the projection screen.
- Page 10 Fuel Effects WARNING: DC SUPPLY 12V IMPORTANT: FUEL EFFETCS MUST BE POSITIONED ACCORDING TO THE E-FX LOG INSTRUCTION BOOKLET. CARE MUST BE TAKEN TO ENSURE THE CHANNEL AT THE AT THE FRONT OF THE FIRE IS NOT OBSTRUCTED. ANYTHING DROPPED IN DURING FITTING OF THE FUEL EFFECTS, MUST BE REMOVED BEFORE INSTALLING THE FRONT GLASS PANEL.
- Page 11 Place the handle (D) onto the top right-hand side of the glass. The upper glass rail is magnetic and will easily fix into place along the top of the opening (E). Adjust the position of the handle (D) to fit into the gap on the rail.
- Page 12 0.0005 0.005 0.0005 Type of heat output/ room temperature control With distance control option Room temperature control, with open window detection Adaptive Start With electronic room temperature control plus week timer Contact Details: Flamerite Fires Ltd. WS13 7AU. UK. www.flameritefires.com...
- Page 13 Maintenance & Trouble Shooting WARNING: Before any maintenance is undertaken, always disconnect the fire from the mains power supply. Maintenance must be undertaken by a Flamerite service engineer or similarly qualified persons in order to avoid a hazard. Replacements part are available from www.flameritefires.com PROBLEM POSSIBLE CAUSE SOLUTION...
- Page 14 Wiring Diagrams...