Advertisement
IMPORTANT, Please Note :
The
Rinseable "TapClean" HEPA Dust Cup
Filter will stop most of the tiniest dust
particles from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Dust Cup Filter
will quickly accumulate dirt inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA Filter as described in this section,
then reconnect unit and proceed with
vacuuming.)
7. Vigorously "TapClean"
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter.
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
Fig. A
is properly
Wash
"TapCleaned"
once a
after each use
month or
when
and suction
suction
does not return
appears
to 100%, then
reduced
we suggest that
the HEPA filter
Warning:
Allow 24
be "TapCleaned"
hours for drying before
vigorously until
replacing in unit.
no more dust
can be removed, then rinsed under
the faucet and allowed to dry for 24
hours before refitting into the vacuum.
(Fig. A) This should be done once a
month or when suction appears to
be reduced.
Important
: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
8. Reassemble the debris screen to the
HEPA filter cartridge and replace into
dust cup (container). Ensure that the
filter assembly is completely seated
inside the dust cup (container).
Important:
Do NOT use the HEPA filter
cartridge without the debris screen in
place.
9. Insert the Rinseable "TapClean"
HEPA dust cup filter back into the
dust cup.
10. Re-install dust cup into the vacuum.
Close cover and re-attach hose.
IMPORTANT:
Please note that there
is a safety switch inside the vacuum
where the dust cup is inserted to
prevent the unit from being run
without a dust cup filter in place. If the
dust cup filter has not engaged this
safety switch, the vacuum will NOT
operate. Therefore, ensure that the
dust cup filter is inserted firmly into the
vacuum when assembling.
Rev. 06/04
Printed in Mexico
IMPORTANT, Please Note :
The
Rinseable "TapClean" HEPA Dust Cup
Filter will stop most of the tiniest dust
particles from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Dust Cup Filter
will quickly accumulate dirt inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA Filter as described in this section,
then reconnect unit and proceed with
vacuuming.)
7. Vigorously "TapClean"
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter.
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
Fig. A
is properly
Wash
"TapCleaned"
once a
after each use
month or
when
and suction
suction
does not return
appears
to 100%, then
reduced
we suggest that
the HEPA filter
Warning:
Allow 24
be "TapCleaned"
hours for drying before
vigorously until
replacing in unit.
no more dust
can be removed, then rinsed under
the faucet and allowed to dry for 24
hours before refitting into the vacuum.
(Fig. A) This should be done once a
month or when suction appears to
be reduced.
Important
: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
8. Reassemble the debris screen to the
HEPA filter cartridge and replace into
dust cup (container). Ensure that the
filter assembly is completely seated
inside the dust cup (container).
Important:
Do NOT use the HEPA filter
cartridge without the debris screen in
place.
9. Insert the Rinseable "TapClean"
HEPA dust cup filter back into the
dust cup.
10. Re-install dust cup into the vacuum.
Close cover and re-attach hose.
IMPORTANT:
Please note that there
is a safety switch inside the vacuum
where the dust cup is inserted to
prevent the unit from being run
without a dust cup filter in place. If the
dust cup filter has not engaged this
safety switch, the vacuum will NOT
operate. Therefore, ensure that the
dust cup filter is inserted firmly into the
vacuum when assembling.
Rev. 06/04
Printed in Mexico
Advertisement
