Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cambridge Audio Minx S325
Summary of Contents for Cambridge Audio Minx S325
- Page 1 Minx S325 Speaker Bundle Manual Generated: 06/02/2023 - 01:45...
-
Page 2: Table Of Contents
目錄 Minx S325 Speaker Bundle ........................................Introduction ............................................... What's included with the Minx S325 bundle? ..................................Minx MIN22 front and rear ........................................Minx X301 front and rear .......................................... Minx MIN22 installation ..........................................Minx X301 unboxing and installation ..................................... Technical specifications ........................................... -
Page 3: Minx S325 Speaker Bundle
Minx S325 Speaker Bundle Last updated: 二月 2, 2023 04:01. Revision #8802 Users Manual... -
Page 4: Introduction
Last updated: 二月 2, 2023 04:43. Revision #8810 Thank you for purchasing this Cambridge Audio Minx Minx S325 loudspeaker bundle. We hope that you enjoy many years of listening pleasure from it. Your loudspeakers can only be as good as the system it is connected to. Please do not compromise on your amplifier. -
Page 5: What's Included With The Minx S325 Bundle
What's included with the Minx S325 bundle? Last updated: 二月 2, 2023 04:43. Revision #8811 1. Quick start guide. 2. 5 x Minx MIN22 compact speaker. 3. Minx X301 subwoofer. 4. 25m speaker cable. 5. 5m RCA subwoofer lead. -
Page 6: Minx Min22 Front And Rear
Minx MIN22 front and rear Last updated: 二月 2, 2023 04:42. Revision #8803 Front. 1. 2 x 2.25" BMR driver. Rear panel. 1. Mounting screw thread. 2. +/- Speaker connection terminals. -
Page 7: Minx X301 Front And Rear
Minx X301 front and rear Last updated: 二月 2, 2023 04:43. Revision #8804 Front. 1. 8" Subwoofer. Rear. 1. AC power socket. 2. Mains power switch – Switch the subwoofer between on and off. 3. Standby switch - Switch between ‘Force On’ (no standby), and ‘Audio Detect’. In audio detect mode the X301 will switch on when it detects an... - Page 8 incoming signal. 4. Crossover frequency control - Adjust the crossover frequency of the subwoofer. 5. Phase control - Adjust the phase settings of the subwoofer. 6. Volume control - Adjust the volume of the subwoofer. 7. Audio in/out.
-
Page 9: Minx Min22 Installation
Minx MIN22 installation Last updated: 二月 2, 2023 04:43. Revision #8805 1. Firstly, ensuring to match the polarity/colour coding, connect the supplied speaker terminals to the speaker outputs of your amplifier or receiver by unscrewing the ends, and securing the speaker cable in the available hole on each terminal. These terminals can then be installed into the rear of the MIN22 with the cables connected. -
Page 10: Minx X301 Unboxing And Installation
Minx X301 unboxing and installation Last updated: 二月 2, 2023 04:43. Revision #8806 Unboxing your Minx X301 subwoofer. Follow the diagram and take care when unboxing your Minx X301 so not to damage the speaker cone. Installation of your Minx X301. Dependent on your desired setup, there are a few different ways to connect your Minx X301 subwoofer. - Page 11 3. Once connected you can decide where to position your subwoofer. As low frequency content is largely unidirectional, you can experiment to find a place that suits your setup. 4. Use the crossover frequency, phase, and volume controls to adjust the subwoofer output to fit with the rest of your system, and your requirements.
-
Page 12: Technical Specifications
Technical specifications Last updated: 二月 2, 2023 04:43. Revision #8807 Minx MIN22. Sensitivity (SPL) Frequency Response 120Hz - 20kHz Impedance 8 Ohms Compatible Drivers 2 x 2.25" BMR Driver Recommended Amplifier Power 25 - 200 Watts Speaker Dimensions (H x W x D) 154 x 78 x 85mm. -
Page 13: Frequently Asked Questions
Frequently asked questions Last updated: 二月 2, 2023 04:43. Revision #8808 What is meant by speaker sensitivity? Speaker sensitivity is the level produced by the speaker at one meter, when supplied with one watt of power from an amplifier. It’s a way of describing how well the speaker produces acoustic energy, based on a given input. -
Page 14: Troubleshooting
Troubleshooting Last updated: 二月 2, 2023 04:43. Revision #8809 No sound through one or both channels. • Check that the amplifier is turned on. • Ensure that the correct input source is selected on the amplifier. • Confirm that all connections between the amplifier and loudspeakers are secure. •...