Download Print this page

Advertisement

User's Manual
MultiSync P701

Advertisement

   Also See for NEC MultiSync P701

   Related Manuals for NEC MultiSync P701

   Summary of Contents for NEC MultiSync P701

  • Page 1

    User’s Manual MultiSync P701...

  • Page 2: Table Of Contents

    MULTI DISPLAY ... English-24 DISPLAY PROTECTION ... English-25 ADVANCED OPTION ... English-25 Remote Control Function ... English-28 Controlling the LCD monitor via RS-232C Remote Control ... English-30 Controlling the LCD monitor via LAN Control ... English-31 Features ... English-34 Troubleshooting ... English-35 Specifications ...

  • Page 3: Declaration Of Conformity

    Declaration of conformity FCC Information 1. Use the attached specified cables with the MultiSync P701 (L709NG) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance.

  • Page 4: Important Information

    Voltage 120* *When operating the MultiSync LCD monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased.

  • Page 5: Safety Precautions, Maintenance & Recommended Use

    Do not use monitor in high temperature, humid, dusty, or oily areas. • If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care. • Allow adequate ventilation around the monitor, so that heat can properly dissipate.

  • Page 6: Contents

    Remember to save your original box and packing material to transport or ship the monitor. Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

  • Page 7: Installation

    Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. • NEC strongly recommends using size M8 screws (14-15 mm + thickness of bracket and washer in length).

  • Page 8: Attaching Mounting Accessories

    Make sure there is nothing on the table that can damage the monitor. When using mounting accessories other than those that are NEC-compliant and approved, they must comply with the VESA-compatible mounting specifications. 2. Using optional tabletop stand CAUTION: Installing and removing the stand must be done by using eyebolts (M12).

  • Page 9: Ventilation Requirements

    When using the display with the optional tabletop stand, fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling. Fasten the cord or chain to the monitor using the eyebolts (M8).

  • Page 10: Parts Name And Functions

    * If “OFF” is selected in “POWER INDICATOR” (see page 24), LED will not light when the LCD monitor is in active mode. AMBIENT LIGHT SENSOR Detects the level of ambient light, allowing the monitor to make automatic adjustments to the brightness setting, resulting in a more comfortable viewing experience.

  • Page 11: Terminal Panel

    MultiSync monitors via RS-232C daisy Chain. LAN port (RJ-45) LAN connection. See page 31. REMOTE IN/OUT Use the optional wired remote control by connecting it to your monitor. NOTE: When you use Remote IN/OUT, IR CONTROL in OSD menu should be NORMAL. English-9...

  • Page 12

    Kensington Lock For security and theft prevention. EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1, 2, 3, DPORT, HDMI and TV jack. Note: This speaker terminal is for 15W + 15W (8 ohm) speaker. Option board slot Slot for board accessories.

  • Page 13: Wireless Remote Control

    Wireless Remote Control POWER button Switches the power on/standby. INPUT button Selects input signal. DVI: DVI DISPLAYPORT: DPORT VGA: VGA RGB/HV: RGB/HV HDMI: HDMI DVD/HD: DVD/HD1, DVD/HD2, SCART VIDEO: VIDEO1, VIDEO2 S-VIDEO: S-VIDEO OPTION: Depends on your connection PICTURE MODE button Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1], [AMBIENT2].

  • Page 14: Operating Range For The Remote Control

    *1: The product you purchased may not have this feature. Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.) from remote control sensor or at a horizontal and vertical angle of within 30°...

  • Page 15: Setup

    C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

  • Page 16: External Equipment

    5. Attach the cable cover • Use six of the M4 screws (included) to attach the cable cover. 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 7.

  • Page 17: Connections

    Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.

  • Page 18: Connecting A Personal Computer

    Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.

  • Page 19: Basic Operation

    The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.

  • Page 20: Power Indicator

    *3 “RS-232C” is selected in EXTERNAL CONTROL. *4 DDC/CI should be disabled. *5 No DisplayPort connection. Using Power Management The LCD monitor follows the VESA approved DPM Display Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period.

  • Page 21: Information Osd

    IN BRIGHT: This is the brightness level that the monitor will go up to when the ambient light level is highest. IN DARK: This is the level of brightness that the monitor will go down to when the ambient light level is low.

  • Page 22: Osd (on-screen-display) Controls

    OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item Sub Menu PICTURE MODE Press UP or DOWN button to select sub-menu. Remote Control Press UP or DOWN button to select.

  • Page 23: Picture

    (S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE A programmable gamma curve can be loaded using NEC optional software. MOVIE SETTINGS NOISE REDUCTION Adjusts the amount of noise reduction. Press + or - to adjust.

  • Page 24: Audio

    Adjusts the vertical size of the image. VGA, RGB/HV inputs only INPUT RESOLUTION If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AUTO SETUP” if required. VGA, RGB/HV inputs only If no problem is detected, the only available option will be “AUTO”.

  • Page 25: Pip

    Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS. KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD. PIP MODE...

  • Page 26: Multi Display

    Sets the monitor ID number from 1-100 and group ID from A-J. NOTE: Group ID is made of multiple selections. IR CONTROL Selects the mode of the monitor for use with the infra-red remote control when using the RS-232C daisy chain. NORMAL The monitor will be controlled normally by wireless remote controller.

  • Page 27: Display Protection

    When the current video input signal is not present, then the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically.

  • Page 28

    GAIN Adjusts gain value. OFFSET Adjusts slice level of synchronized signal. SYNC TERMINATE Selects the terminate resistance for matching the cable impedance. RGB/HV inputs only TERMINAL SETTING DVI MODE Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when PC or other computer equipment is connected.

  • Page 29

    To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

  • Page 30: Remote Control Function

    2. Set Monitor ID and IR Control mode. For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under the “MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share the same Monitor ID number.

  • Page 31

    Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor. Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy chained monitors simultaneously, select “ALL”...

  • Page 32: Controlling The Lcd Monitor Via Rs-232c Remote Control

    NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details. * In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model. Do not connect to other types of equipment.

  • Page 33: Controlling The Lcd Monitor Via Lan Control

    To perform the monitor control from a web browser, you must have an exclusive application installed on your computer. The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP server function.

  • Page 34: Network Settings

    Regarding the actual address that is entered for the address or entered into the URL column when operation of the monitor is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the monitor has been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of the monitor has been set in the “HOSTS”...

  • Page 35

    Type in the hostname of the network connected to the monitor. Up to 60 alphanumeric characters can be used. DOMAIN NAME Type in the domain name of the network connected to the monitor. Up to 60 alphanumeric characters can be used. ALERT MAIL Checking [ENABLE] will turn on the Alert Mail feature.

  • Page 36: Features

    VESA Standard (FDMIv1) Mounting Interface: Allows users to connect their LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.

  • Page 37: Troubleshooting

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

  • Page 38: Specifications

    Specifications Product Specifications LCD Module Design View Distance: Frequency Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector Digital RGB DVD/HD1 RCA (Y, Cb/Pb, Cr/Pr) Component...

  • Page 39: Pin Assignment

    1) RS-232C input/output Pin No Name connected to 7&8 connected to 6 connected to 4 connected to 1&8 connected to 1&7 This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) REMOTE IN 3) REMOTE OUT D-SUB 9P English-37...

  • Page 40: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

This manual also for:

Multisync p701-avt, P701-r

Comments to this Manuals

Symbols: 0
Latest comments: