Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for icherng CDT Series
Summary of Contents for icherng CDT Series
-
Page 3: Table Of Contents
Catalog 目錄 1. Check on delivery 收貨檢查 .................. 1 2. Storage 儲存......................1 3. Installation 安裝 ..................... 2 3.1 Install into system 安裝至系統 ................. 2 3.2 General rules for positioning condenser 安置冷凝器的通則 ......3 3.3 Refrigerant Piping 冷媒配管 ................4 3.4 Wiring 電路接線... -
Page 5: Check On Delivery 收貨檢查
1. 收貨檢查 1. Check on delivery 當收到產品時，請檢查產品包裝與產品本身是否 When receive the product, please check if there is any damage on packing or product due to shipping. And 有運輸損傷。並請核對產品與送貨單內容是否符合。 the content is the same as packing list. If there is any 如果任何損傷，請於送貨單上註明損害情形。可能的 damage, please describe the defect on the delivery note. -
Page 6: Installation 安裝
Use suitable equipment to 慎選合適的機具搬運本產 handle this product. For 品。如為棧板包裝產品請選 pallet packing, please use 用正確的堆高機進行本產品 correct forklift to transport! 的運送 ！ Installation work must be executed by professional 本產品的安裝作業僅能 technician！ 由專業作業人員執行！ 3. Installation 3. 安裝 3.1 Install into system 3.1 安裝至系統 Note! This series is only for install indoors or in a ventilated cabinet. -
Page 7: General Rules For Positioning Condenser 安置冷凝器的通則
3.2 冷凝器的安裝位置 3.2 Positioning condenser 為了確保冷凝器能發揮最大的效能，必須要將冷 In order to get the best performance of your 凝器裝置在正確的位置。在選擇安裝位置時，必須要 condenser, you must install the condenser in a correct place. The following general rules must be followed 遵守以下的通則： while selecting the position for condenser: 1. -
Page 8: Refrigerant Piping 冷媒配管
Caution！ 注意！ Piping working must be executed 配管作業必須由專業人員執行！ by professional technician! 3.3 冷媒配管 3.3 Refrigerant Piping ※配管必須符合國家相關法規與系統實際操作需求。 * Refrigerant piping must be done by professional technician and follow the national codes. 並由專業技術人員執行。 * Please follow ASHRAE guide line for refrigerant ※請依照... -
Page 9: Test Running And Adjustment 試車與調整
4. 試車與調整 4. Test running and adjustment 4.1 啟動前檢查 4.1 Before start up 在啟動系統之前，請仔細確認以下相關事項： Before setting system into working, the following check list must be examined very carefully: 確認風車支架是否被牢固鎖定，所有的螺絲已被 旋緊。運轉前確認無其他鬆動零件。 Check fan support(s) is/are fastened firmly. All the screws are fixed. There is no loose part before 檢查冷凝器的水平是否正確。. -
Page 10: Maintenance 保養
5. Maintenance 5. 保養 In order to keep condenser in a good condition, you 為確保冷凝器維持良好的運轉狀態，請定期檢查 have to check the condenser periodically. The following 並保養冷凝器。 items must be done for check. 定期清潔鰭片確保熱傳效能的維持。使用清水清 Clean the fins periodically for retaining performance. 潔鰭片，水的壓力必須要低於 4 bar。清潔時要注 Use clean water to wash fins. -
Page 11: Trouble Shooting 故障排除
6. Trouble shooting Symptoms Possible causes Correction Condensing temperature is Condenser is dirty Clean condenser. too high Supply voltage to fan(s) is too low Check the power source. Heat source nearby or short circuit in Remove heat source or any obstacle causes air flow short circuit. - Page 12 Memo 備忘...
-
Page 13: Appendix 2 Replacement Parts 替換零件表
Appendix 1 Replacement Parts 替換零件表 Model No. Fan Set Model No. Fan Set 型號 風車組 型號 風車組 CDT048-2 AAHUJ CDT500-2 AAHWD CDT075-2□ AAHUW CDT600-2 AAHWD CDT100-1□ AAVQK CDT700-2 AAHWD CDT100-2□ AAHUW CDT800-2 AAHWD CDT125-2□ AAHUW CDT900-2 AAYBR CDT150-1□ AAVQK CDT1000-2 AAYBR CDT150-2□... - Page 14 Version 2016.08.0.1 Subject to change without notice! 資料變更恕不另行通知！ I-Cherng Refrigeration Industrial Co., Ltd. 一丞冷凍工業股份有限公司 Heat Exchanger Taiwan 熱交換器 台灣製造 No.12 Chu Kuang 1st St., Daliao Dist., Kaohsiung City, 83164, Taiwan 台灣高雄市大寮區莒光一街 12 號 Tel:07-7873666 Fax:07-7872999 Website: www.icherng.com.tw Email: icherng.com@msa.hinet.net...