Transportation And Storage; Maintenance; Clearing Blockages - AEG A58LMWSP282 Original Instructions Manual

■ Hands and feet of all persons are not clear of the cutting
enclosure.
des,
Never operate the product if the on/off switch on the handlebar does
not properly start and stop the product.
erve
Never attempt to lock the on/off switches in the on position; this is
extremely dangerous.
ged
Do not force the product. It will do the job better and safer at the
speed for which it was designed.
Stop the blade when crossing gravel surfaces.
you
Avoid holes, ruts, bumps, rocks, property stakes, or other hidden
own
objects. Uneven terrain could cause a slip-and-fall accident.
t.
Always ensure that the motor control cable is never trapped, pinched,
s to
or otherwise damaged during assembly or when folding the handle.
ass,
Injuries may be caused, or aggravated, by prolonged use of the
product. When using the product for prolonged periods, ensure to
hout
take regular breaks.
ADDITIONAL BATTERY SAFETY WARNINGS
the
t of
To reduce the risk of fire, personal injury, and product damage due
ress
to a short circuit, never immerse the tool, battery pack, or charger in
duct
fluid or allow fluid to flow inside them. Corrosive or conductive fluids,
ting.
such as seawater, certain industrial chemicals, and bleach or bleach-
y of
containing products, etc., can cause a short circuit.
ade.
OVERLOAD, OVERHEAT, AND TILT PROTECTION
tery
The product has an overload protection device. When overloading is
eep
detected, the product automatically turns off. If the overload protector
near
is actuated, release the on/off bail bar. Press the start button, and
squeeze the on/off bail bar to restart the product. If the product still
does not start, reinstall the battery pack.
tery
The battery pack has overheat protection. Excessive temperatures
op:
causes the battery to stop powering the product. If the battery pack
is too warm, allow it to cool down before resuming operation. If the
al of
product still does not work, recharge the battery.
NOTE: The battery pack LED indicator stops working if the battery
protection feature has caused the battery pack to stop powering
the product. Turn off the product or remove the battery pack from
arge
the product, and the battery pack LED indicator will resume normal
function.
and
The tilt protection function stops the product if the it is tilted beyond
the
45°, for about 7 seconds. The product will not function if the tilt angle
limit is exceeded or if the product is in the vertical storage position.
y)

TRANSPORTATION AND STORAGE

Turn off the product, and remove the isolator key and the battery
pack. Make sure that all moving parts have come to a complete stop.
Allow the product to cool down before storing or transporting.
und
Remove all foreign materials from the product. Store the product in
a cool, dry, and well-ventilated place that is inaccessible to children.
wear
Keep the product away from corrosive agents such as garden
bolt
chemicals and de-icing salts. Do not store the product outdoors.
For transportation in vehicles, remove the isolator key, and secure the
n.
product against movement or falling to prevent injury to persons or
s in
damage to the product.
Use extreme caution when lifting or tilting the product for
the
maintenance, cleaning, storage, or transportation. The blade is sharp.
Keep all body parts away from the blade while it is exposed.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions
and regulations.
Follow all special requirements on packaging and labelling when
transporting batteries by a third party.
Ensure that no batteries can come in contact with other batteries
or conductive materials while in transport by protecting exposed
connectors with insulating, non-conductive caps or tape. Do not
transport batteries that are cracked or leaking. Check with the
forwarding company for further advice.

MAINTENANCE

Use only original manufacturer's replacement parts, accessories, and
attachments. Failure to do so can cause possible injury, can contribute
to poor performance, and may void your warranty.
Servicing requires extreme care and knowledge and should be
performed only by a qualified service technician. Have the product
serviced by an authorised service centre only.
Turn off the product, and remove the isolator key and the battery
pack. Make sure that all moving parts have come to a complete stop
before any cleaning or maintenance task.
Replace worn or damaged parts for safety.
Frequently check the grass catcher for wear or deterioration.
Check all nuts, bolts, and screws at frequent intervals for proper
tightness to ensure that the product is in safe working condition.
Be careful during adjustment of the product to prevent entrapment
of the fingers between moving blades and fixed parts of the product.
When servicing the blades, be aware that even though the power
source is turned off, the blades can still be moved.
Replace damaged blades and bolts in sets to preserve balance.
You may make adjustments and repairs described in this manual.
For other repairs, have the product serviced by an authorised service
centre only.
After each use, clean the plastic parts with a soft, dry cloth. Any
part that is damaged should be properly repaired or replaced by an
authorised service centre.
The blade on the product is sharp. Use extreme caution, and wear
heavy-duty gloves when fitting, replacing, cleaning, or checking bolt
security.
The blade bolts must be adequately tightened. See the manufacturer's
recommendations for blade bolt torque, which can be found in the
product specification table in this manual.

CLEARING BLOCKAGES

Turn off the product, and remove the isolator key and the battery
pack. Make sure that all moving parts have come to a complete stop.
Always wear heavy-duty gloves when checking or clearing a blockage.
The blades are sharp, and the blockage itself could be a sharp object.
Remove the grass catcher. Check and carefully clear the grass catcher
for obstructions.
Check and carefully clear the grass discharge chute for clear
blockages.
Turn the product on its side. Check its underside and the area around
the blade. Carefully remove any blockages. Remember that the blade
may move during cleaning.
27
27