Page 3
Grazie per aver scelto un nostro prodotto...
Page 4
Informazioni prodotto Lettore codice a barre USB plug & play in grado di leggere tutti i codici a barre standard 1D e 2D quali: Codebar,Code11,Code39/Code93, UPC/EAN,CODE128/CODE32,EAN128,InterLeaved2of5,- Matrix2of5,MSICODE,Standard2of5,QR CODE Contenuto della confezione n°1 Lettore codice a barre n°1 Cavo n°1 Manuale utente Avvertenze e Precauzioni Leggere attentamente le istruzioni per l’uso e rispettare in particolare le avvertenze per la sicurezza.
Page 5
• Nel caso non sia più possibile l’uso sicuro, disattivare il prodotto ed evitare che possa essere utilizzato in modo non intenzionale. L’uso sicuro non è più garantito se il prodotto: - presenta danni visibili - non funziona più correttamente, - è stato conservato per periodi prolungati in condizioni ambientali sfavorevoli oppure - è...
Page 6
Angolo di lettura). • Per leggere il codice a barre, premere il tasto scansione. Se la lettura è avvenuta con succes- so, avvertirete un segnale acustico. Suggerimenti e consigli • Assicurarsi che il codice a barre da leggere sia pulito. •...
Page 7
Parametri Tecnici Interfaccia USB, RS-232 Sensore Sensore Planar CMOS Sorgente Luminosa LED rosso (puntatore) + LED Bianco (Flash) Processore MCU 32-bit Decodifica Codebar,Code11, Code39/Code93, UPC/EAN,CODE128/ EAN128,InterLeaved2of5,Matrix2of5,MSICODE,Standar- d2of5,QR CODE Risoluzione CODE39 5mil, QR 8.7 mil, PCS45% Profondità di Campo 5MIL CODE39: 5—12 CM 15MIL CODE39: 4—25 CM 10MIL CODE93: 4—21 CM 15MIL UPC/EAN: 4—25 CM...
Page 8
Contrasto Angoli di Scansione Roll 0-360°, ± Pitch 65°, Yaw ±60° Parametri Fisici Materiale ABS + PVC + PC Dimensioni (mm) 157L x 71W x 90H Alimentazione DC 5V/300mA Peso 120=5g (senza cavo) Parametri Ambientali Grado IP IP 54 Temperatura Operativa da 0 a 50°C / da 32 a 122 °F Temperatura Stoccaggio da 0 a 50°C / da 32 a 122 °F...
Page 9
Impostazioni di fabbrica Scansionare “Factory Default”, per tornare alle impostazioni di fabbrica. Nota: Il seguente codice di configurazione riporta lo scanner alle impostazioni iniziali Codice di configurazione ON/OFF Se il codice di configurazione è impostato su “ON”, è possibile configurare lo scanner tramite la scansione dei codici a barre di impostazione.
Page 10
Impostazioni LED L’indicatore LED offre una migliore lettura del codice. Migliora la lettura dei codici in ambienti poco illuminati. Modalità Normale: L’indicatore LED si accende quando viene premuto il pulsante. Sempre Acceso: L’indicatore LED è sempre acceso quando lo scanner viene messo in corrente. Spento: L’indicatore LED è...
Page 11
Impostazioni interfaccia Interfaccia usb Quando lo scanner viene collegato al PC tramite cavo USB, può essere impostato in modalità tastiera eseguendo la scansione del codice a barre seguente. VCOM Quando lo scanner viene collegato al PC tramite cavo USB, può essere impostato in modalità VCOM (virtual serial port), scansionando il codice a barre seguente (contattare il fornitore per i driver d’istallazione) RS232...
Page 12
Impostazione della velocità di trasmissione dell’interfaccia RS-232 In modalità RS-232 la velocità di trasmissione predefinita è di 960 bps, è possibile cambiare la velocità di trasmissione scansionando uno dei seguenti codici a barre di seguito. Impostazione Suffisso...
Page 13
Impostazione Modalità di scansione Impostazione Intervallo di lettura E’ possibile impostare il tempo di intervallo di lettura scansionando uno dei seguenti codici a barre di seguito. Impostazione durata singola scansione E’ possibile impostare l’intervallo di tempo tra una scansione e l’altra quando lo scanner è impostato in modalità...
Page 14
Impostazione tempo stabilizzazione immagini. Questa funzione permette di impostare il tempo di stabilizzazione dell’immagine prima che venga effettuata la lettura, quando è impostato in modalità scansione automatica. Impostazioni Lingua...
Page 15
Informazione sulla Versione Per vedere la versione dello scanner è necessario collegare lo scanner al PC e scansionare il codice di seguito Configurazione codice a barre disponibili/ vietati Decodifica tutto il codice a barre Lo scanner consente di leggere o vietare la lettura di tutti i codici a barre di supporto se si ese- gue la scansione dei seguenti codici a barre di impostazione.
Page 16
Funzione di Rotazione Codice a barre Scansionare il seguente codice per impostare se lo scanner può effettuare la lettura o meno la lettura a 360° EAN13 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici EAN13. EAN8 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici EAN8.
Page 17
UPCA Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici UPCA UPCE0 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici UPCE0. UPCE1 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici UPCE1.
Page 18
CODE128 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici CODE128. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve per il codice 128. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga per il codice 128.
Page 19
CODE39 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici CODE39. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve per il codice CODE39. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga per il codice CODE39.
Page 20
CODE93 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici CODE93. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve per il codice CODE93. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga per il codice CODE93.
Page 21
CODEBAR Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici CodeBar. Scansionare i seguenti codici per abilitare o disabilitare il prefisso per il codice CodeBar. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve per il codice CodeBar.
Page 22
Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga per il codice CodeBar. Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici QR. 2 di 5 codici Interlacciati Scansionare i seguenti codici per abilitare o disabilitare la lettura di 2 di 5 codici interlacciati.
Page 23
Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve di 2 di 5 codici interlacciati. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga di 2 di 5 codici interlacciati.
Page 24
Industrial 25 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici Industry 25. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve dei codici Industry25. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga dei codici Industry25.
Page 25
Matrix 2 di 5 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici Matrix 2 di 5. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve dei codici Matrix 2 di 5. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più...
Page 26
Code11 Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici Code11. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve dei codici Code11. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga dei codici Code11.
Page 27
Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici MSI. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve dei codici MSI. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga dei codici MSI.
Page 28
RSS (optional) Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici RSS-14. Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici limitativa per RSS. Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici espansiva per RS.
Page 29
Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più breve dei codici RSS. Eseguire la scansione dei seguenti codici a barre per impostare la lunghezza di lettura più lunga dei codici RSS. DM (optional) Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici DM.
Page 30
PDF417 (optional) Scansionare i seguenti codici per abilitare o disabilitare la lettura dei codici PDF417. Barcode Bianco...
Page 32
Dichiarazione di conformità Conformità alle Direttive Europee Con il marchio CE, Mach Power® garantisce che il prodotto è conforme alle norme e direttive europee richieste. Smaltimento del Prodotto In conformità alla normativa WEEE, le apparecchiature elettriche ed elettroniche non devono essere smaltite con i rifiuti domestici. Il presente prodotto deve essere consegnato ai punti di raccolta preposti allo smalti- mento e riciclo delle apparecchiature elettriche ed elettroniche.
Page 35
USER MANUAL BARCODE USB 1D / 2D READER BP-LBSC2D-012...
Page 37
Thanks for choosing one of our products...
Page 38
Product information USB plug & play barcode reader capable of reading all standard 1D e 2D barcodes such as Codebar,Code11,Code39/Code93, UPC/EAN,CODE128/CODE32,EAN128,InterLeaved2of5,Ma- trix2of5,MSICODE,Standard2of5,QR CODE Package content n°1 Barcode reader n°1 Cable n°1 User Manual Warnings and Precautions Read the instructions for use carefully and observe the safety warnings in particular. In the event that the safety warnings and the indications relating to the proper use contained in these instructions for use are not observed, we assume no responsibility for any damage to resulting things or persons.
Page 39
- shows visible damage - it no longer works correctly, - it has been stored for prolonged periods in unfavourable envi- ronmental conditions or - has been exposed to considerable stress due to transport. • Handle the product with caution. Bumps, blows or even falling from a minimum height could damage it.
Page 40
• To read the barcode, press the scan button. If the reading has been successful, you will hear an acoustic signal. Tips: • Make sure the barcode to be read is clean. • The bar code to be read must be completely visible. •...
Page 41
Technical Parameters Interface USB, RS-232 Sensor Planar CMOS sensor Light source Red LED (pointer) + white LED (Flash) Processor MCU 32-bit Decoding Codebar,Code11, Code39/Code93, UPC/EAN,CODE128/ EAN128,InterLeaved2of5,Matrix2of5,MSICODE,Standar- d2of5,QR CODE Resolution CODE39 5mil, QR 8.7 mil, PCS45% Depth of Field 5MIL CODE39: 5—12 CM 15MIL CODE39: 4—25 CM 10MIL CODE93: 4—21 CM 15MIL UPC/EAN: 4—25 CM...
Page 42
Contrast Scan angles Roll 0-360°, ± Pitch 65°, Yaw ±60° Physical Parameters Material ABS + PVC + PC Dimensions (mm) 157L x 71W x 90H Power Supply DC 5V/300mA Weight 120=5g (without cable) Environmental parameters IP degree IP 54 Operating Temperature from 0 to 50°C / from 32 to 122 °F Storage Temperature from 0 to 50°C / from 32 to 122 °F...
Page 43
Factory default setting Please scan “Factory Dfault“, if you need to recover all the initial setting made by factory. Remark : The followingsetup bar codes with means factory initial setting Configuration code ON/OFF When configuration code is set “ON“, user can setup the scanner by scanning the setup bar codes.
Page 44
LED light setting The LED light will offer auxiliary lighting for reading. When the light beam shoots on the target object, it can improve the decoding performance and the adaptability of weak ambient light. User can set the scanner into any of the modes below according to the operation environment. Normale Mode: LED light is on when pressing the button and off at other time.
Page 45
Interface stting USB interface When the scanner connects to the PC via USB cable, user can set it into standard USB PC keyboard mode by scanning the below setup bar code. VCOM When make the scanner connected with the PC USB cable, please set it into VCOM (virtual serial port) mode by scanning the “VCOM”...
Page 46
RS-232 interface baud rate setting The scanner interface is standard RS-232, and the default baud rate is 9600bps. It can alter the baud rate by scanning the following bar codes. Suffix setting...
Page 47
Scanning mode setting Reading interval time setting This function means, after the scanner read successfully and output data, or timeout for one reading, the scanner will get into decoding mode again in a period time (time can be set) Single scan duratipon setting This function is to set the longest duration of scanner decoding before reading successfully in auto sensing mode.
Page 48
Image stable time setting This function is to set the time of image stabilization before reading, when the operation envi- ronment changes in auto sensing mode. Language setting...
Page 49
Version information In order to let the PC read the unit version information, it can confirm the message by scan the following bar code as below Available bar code type / Forbidden configuration All decoding bar code The scanner allows reading or forbids reading all the supporting bar code if scan the following setting bar codes.
Page 50
Bar code rotating function Scan the following bar codes to set the scanner allow or forbid reading the 360° rotating bar code. It can improve the scanning speed if forbid the 360° rotate function. EAN13 Scan the following bar codes to set the scanner allow or forbid reading the EAN13 codes EAN8 Scan the following bar codes to set the scanner allow or forbid reading the EAN8 codes...
Page 51
UPCA Scan the following bar codes to set the scanner allow or forbid reading the UPCA codes UPCE0 Scan the following bar codes to set the scanner allow or forbid reading the UPCE0 codes UPCE1 Scan the following bar codes to set the scanner allow or forbid reading the UPCE1 codes...
Page 52
CODE128 Scan the following bar codes to set the scanner allow or forbid reading the code 128 Scan the following bar codes to setting the shortest reading length for the code 128. Scan the following bar codes to setting the longest reading length for the code 128.
Page 53
CODE39 Scan the following bar codes to set the scanner allow or forbid reading the code 39 Scan the following bar codes to setting the shortest reading length for the code 39 Scan the following bar codes to setting the longest reading length for the code 39...
Page 54
CODE93 Scan the following bar codes to set the scanner allow or forbid reading the code 93 Scan the following bar codes to setting the shortest reading length for the code 93 Scan the following bar codes to setting the longest reading length for the code 93...
Page 55
CODEBAR Scan the following bar codes to set the scanner allow or forbid reading the codebar Scan the following bar codes to set allow or forbid sending the prefix character for codebar Scan the following bar codes to set the shoterst reading length for the codebar...
Page 56
Scan the following bar codes to set the longest reading length for the codebar Scan the following bar codes to set the scanner allow or forbid reading the QR Code Interleaved 2 0f 5 Scan the following bar codes to set the scanner allow or forbid reading the interleaved 2 of 5...
Page 57
Scan the following bar codes to set the scanner shortest reading length for the interleaved 2 of 5 Scan the following bar codes to set the scanner longest reading length for the nterleaved 2 of 5 Industrial 25 Scan the following bar codes to set the scanner allow or forbid reading the Industry 25...
Page 58
Scan the following bar codes to set the scanner shortest reading length for the industry 25 Scan the following bar codes to set the scanner longest reading length for the industry 25 . Matrix 2 di 5 Scan the following bar codes to set the scanner allow or forbid reading the Matrix 2 of 5...
Page 59
Scan the following bar codes to set the scanner shortest reading length for the Matrix 2 of 5 Scan the following bar codes to set the scanner longest reading length for the Matrix 2 of 5 Code11 Scan the following bar codes to set the scanner allow or forbid reading the Code11...
Page 60
Scan the following bar codes to set the scanner shortest reading length for the Code 11 Scan the following bar codes to set the scanner longest reading length for the Code 11 Scan the following bar codes to set the scanner alllow or forbid reading the MSI...
Page 61
Scan the following bar codes to set the scanner shortest reading length for the MSI Scan the following bar codes to set the scanner longest reading length for the MSI RSS (optional) Scan the following bar codes to set the scanner allow or forbid reading the RSS-14...
Page 62
Scan the following bar codes to set the scanner allow or forbid reading the limitative RSS-14 Scan the following bar codes to set the scanner allow or forbid reading the expanding RSS Scan the following bar codes to set the shortest reading length for the RSS...
Page 63
Scan the following bar codes to set the longest reading length for the RSS DM (optional) Scan the following bar codes to set the scanner allow or forbid reading the DM PDF417 (optional) Scan the following bar codes to set the scanner allow or forbid reading the PDF417...
Page 65
Declaration of Conformity Compliance with European Directives With the CE sign, Mach Power® ensures that the product is conformed to the basic European standards and directives Product Disposal This product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste.