Advertisement
18. tool to the power supply. Do not carry a plugged in tool.
19. with your finger on the switch
20.
Use outdoor rated extension cords
are intended for outdoor use and are so marked.
21.
. Watch what you are doing. Use common sense. Do not operate a power tool when
Stay alert
you are tired.
22.
Check for damaged parts
is slightly damaged carefully determine if it will operate properly and perform its intended
function other wise replace. Check for alignment of moving parts binding of moving parts,
breakage of parts, free running of moving parts, proper mounting and any other conditions
that may affect the operation of the tool. A guard or other parts that are damaged should be
properly repaired or replaced by an authorised service centre, unless otherwise indicated in
this instruction manual. Defective switches must be replaced by authorised service facility. Do
not use the tool if the switch does not turn the tool on and off correctly.
23.
The use of any accessory or attachment, other than those recommended in this
Warning.
instruction manual, may present a risk of personal injury.
24.
Have your tool repaired by a qualified person
relevant safety requirements. Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable danger to the user.
25.
Do not let the tool run unattended
stop before leaving it. Then turn off at mains and remove the plug from the power outlet.
WARNING
The use of an accessory or attachment, other than those recommended in this instruction manual may present a risk
of personal injury
The tool must be used only for its prescribed purpose any use other than those mentioned in this manual will be
considered a case of misuse. The user and not the manufacture shall be liable for any damage or injury resulting
from such cases of misuse.
ADDITION SAFETY RULES FOR ANGLE GRINDER
•
Fully unwind cable drum extensions to avoid potential overheating.
• When an extension cable is required, you must ensure that it has the right ampere rating for your power tool and
is in safe electrical condition.
• Ensure your mains supply voltage is the same as your tool rating plate voltage.
• Always switch off before you put the angle grinder down.
• Keep the area free of tripping hazards.
• Do not let anyone under the age of 18 years operate this tool.
• Rags, cloths, cord, string and the like should never be left around the work area.
• If you are interrupted when operating the tool, complete the process and switch off before looking up.
• Periodically check that all the nuts, bolts and other fixings are properly tightened.
• Abrasive wheels shall be stored and handled with care in accordance with manufacturers instructions
• Do not store materials or equipment above a machine in such a way that they could fall into it.
• Do not use discs having a maximum permissible speed below the tool rated marked RPM.
•
Inspect the grinding wheel before use, do not use chipped, cracked or otherwise defective products.
disc before mounting it into the angle grinder. Check by striking it with a wooden handle whilst balancing the
disc on your finger. Listen to the sound it makes if it rings it is ok if it sounds dull it may be cracked and needs to
be replaced.
Ensure that mounted wheels and points are fitted in accordance with the manufacturer's instructions.
• When the disc is installed, run it for at least a minute to ensure that it does not have a fault. It is always advisable
to stay out of the line of the disc when testing or in general use.
• Do not use a disc marked with a lower RPM than that of the no load speed shown on the rating plate.
• Use discs only of the prescribed diameter.
• Never try to operate the angle grinder without the guard in place.
Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels.
For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to
accept the spindle length;
Do not use cutting off wheel for side grinding.
Ensure that sparks resulting from use do not create a hazard e.g. do not hit persons, or ignite flammable
substances.
Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary
to clear dust, first disconnect the tool from the mains supply (use non metallic objects) and avoid damaging
internal parts.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid hazard
. When a tool is used outdoors, use only extension cords that
. Before using a tool, check that there are no damaged parts, if a part
. This electric tool is in accordance with the
. Always wait until your power tool has come to a complete
Check the
Advertisement
