Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cressi AQUAWING
Summary of Contents for Cressi AQUAWING
- Page 1 MANUALE D’USO E Q U I L I B R A T O R I DIRECTION FOR USE B . C . ’ S J A C K E T S MANUEL D’INSTRUCTIONS GILETS STABILISATEURS BEDIENUNGSANLEITUNG T A R I E R J A C K E T S MANUAL DE ISTRUCCIONES CHALECOS HIDROSTÁTICOS MANUAL DO USÁ...
- Page 2 Taglie .................16 Tailles ...............44 Nitrox ............... 30 Nitrox .................16 Nitrox ................44 Marking ..............31 Marcatura ............... 17 Marquage...............45 Garanzia Europea Cressi ....... 17 Cressi European guarantee......31 Garantie Européenne Cressi .....45 Caratteristiche Jackets Cressi ....18 Cressi Jackets features .........32 Caractéristiques Jackets Cressi ....46...
- Page 3 Nitrox ............... 58 Calificacion ............73 Marcação ...............87 标记 ..........101 Kennzeichnung ..........59 Garantía Europea Cressi ......73 Garantia Europeia da Cressi ......87 Europäische Garantie Cressi..... 59 第二个标签 .........101 Características Chaqueta Cressi .... 74 Características do Eigenschaften des Cressi-Jackets ..60 科越思的欧洲质量保修...
-
Page 4: General Warnings
In this way, the diver’s specific weight will vary, making him/her lighter and more dynamic. Its function accounts for the abbreviation CE standards, CRESSI BCDs are certified for use at a maximum depth of 50 “BCD”, i.e. Buoyancy Control Device, the name that is given to these jackets. - Page 5 SECURING THE CYLINDER WITH THE RIGID BACKPLATE. The Cressi rigid backplate has two straps at the rear to fix the tank. These STANDARD AIR CELL straps play a very important role, as they support the entire weight of the The Standard air cell is the most traditional and comfortable one.
- Page 6 THE CYLINDER MAY SLIP OFF. Once the cylinder has been attached, keep the upper side of the backplate from 5 to 10 cm below the valves (fig. 14), so that the diver’s head does not bump against the regulator. www.cressi.com...
-
Page 7: Available Accessories
INTEGRATED WEIGHT POCKETS AVAILABLE ACCESSORIES The Aquawing + model is equipped with a system that allows you to insert the Two type of accessories are available that can be assembled on both the weights directly into special pockets. Thanks to this solution, the diver is not... -
Page 8: Harness Adjustments
HARNESS ADJUSTMENTS The Aquawing and Aquawing + are one-size annular BCDs designed to adapt to Proceed as follows to remove the BCD (loosen the harness): open the crotch all body types (male and female) using the new patented Modular Adjustment... - Page 9 D-RING ADJUSTMENT To change the position of the D-ring on the shoulder strap, proceed as shown in the following figures (fig. 27-28-29-30-31-32-33-34-35-36-37-38-39-40)
-
Page 10: Control Unit
By-Pass by way of a quick coupling. This allows the By-Pass valve to blow air into the tank. This valve is designed to operate with a relative pressure of 1 to 15 bar, but we recommend using it with a relative pressure of 8 to 12 bar. www.cressi.com... - Page 11 - If it has been subjected to traction that goes beyond normal use, such i WARNING! as lifting the self-contained breathing apparatus or becoming caught Only use the original Cressi hoses supplied. If you need to during sudden movements. replace them, we recommend using Cressi hoses.
-
Page 12: Control Unit Functions
4 - Traditional deflation: with the body in a vertical position, raise the corrugated hose towards the surface and press button C (fig. 53). FLAT CONTROL UNIT The quick dump valve has a considerably smaller footprint and lower weight. It is not equipped with a pressure relief valve (fig. 54). www.cressi.com... -
Page 13: Emergency Release
VALVES PUTTING THE BCD ON: To allow the air to escape from the bladder, each Cressi BCD has a control Using both hands, grasp the ends of the abdominal strap and pull it upwards unit with two valves, as laid out above. The Aquawing and Aquawing + and outwards (about 45 degrees) from the body. -
Page 14: Pre-Dive Checks
We recommend practising both methods extensively, even if the first proves quicker and easier. The position of the diver is not relevant to the effects of the manoeuvre. Deflation manoeuvres are carried out by way of www.cressi.com... -
Page 15: Maintenance
USE AND DURATION LIMITS 6 - Replace the hose seals annually at an authorised Cressi centre. 7 - We recommend getting your BCD inspected annually at an authorised This BCD must not be used beyond the first 50 metres of depth. - Page 16 Pictogram indicating the max. tank capacity in litres and the maximum diameter. CRESSI EUROPEAN GUARANTEE In accordance with the 1999/44 EC directive, Cressi guarantees its products against non-conformity and defects affecting proper functioning. To offer better service to its customers and consumers and to highlight the efficiency...
- Page 17 CRESSI JACKETS FEATURES AQUAWING AQUAWING + MODEL: TYPE OF BACK CELL NYLON 210 D CORDURA 1000 D BACK CELL NYLON 210 D CORDURA 1000 D AIR CELL - MATERIAL TYPE OF BACKPLATE/ RIGIDO / RIGIDO / CYLINDER FIXING DOPPIA FASCIA...
- Page 18 Cressi Sub S.p.A. Headquarters: Via G. Adamoli, 501 16165 Genova, Italy + 39 010 830791 www.cressi.com info@cressi.com...
Need help?
Do you have a question about the AQUAWING and is the answer not in the manual?
Questions and answers