Related Manuals for Outback Power Systems FLEXware
Summary of Contents for Outback Power Systems FLEXware
- Page 1 Mounting Plate User’s Guide Includes Mounting, Installation, and Product Registration...
- Page 2 OutBack Power Systems FLEXware is a system of modular aluminum mounting hardware and installation components designed for convenient system installation and integration. About OutBack Power Systems OutBack Power Systems is a leader in advanced energy conversion technology. Our products include true sine wave inverter/chargers, a maximum power point charge controller, system communication components, as well as breaker panels, breakers, accessories, and assembled systems.
- Page 3 Requirements and Warnings The OutBack FLEXware Mounting Plate is listed by ETL to UL standard UL 508A Industrial Control Panels. Grounding Instructions – Any enclosures attached to the FLEXware Mounting Plate should be con- nected to a grounded, permanent wiring system. For most installations, the negative battery con- ductor should be bonded to the grounding system at one (and only one) point in the DC system.
- Page 4 • FLEXware 250 for single FX Series Inverter/Charger installations along with the desired AC and DC disconnects • FLEXware 500, which supports up to two FXs and two MX Charge Controllers, accommodat- ing both split-phase and/or higher power output as needed •...
-
Page 5: Mounting Plate Dimensions
Mounting Plate Dimensions Front View Side View Figure 1: FLEXware Mounting Plate Dimensions... -
Page 6: Mounting And Installation
Mounting and Installation Slot indicates this is the top edge of the FW-MP Lag Bolts Insert hanging screws from back Lag Bolts Figure 2: FLEXware Mounting Plate... - Page 7 Installing a Single FLEXware Mounting Plate • The FLEXware Mounting Plate (FW-MP) must be secured to a surface that can safely hold approximately 200 lbs of components and metal hardware; OutBack Power Systems recom- mends the FW-MP be attached in at least six places with a minimum 2” X ¼” lag bolts/lag screws and flat washers screwed into either wall studs or posts.
- Page 8 Installing Two FLEXware Mounting Plates • Install the FX Series Inverter/Charger hanging screws (see Figure 2) for each FX used in the system before hanging the FW-MP to a wall. Install the hanging screws from the back of the FW-MP.
- Page 9 Hanging Straps Figure 3: Two mounting plates installed Please see the FLEXware 500 or FLEXware 1000 installation manuals for system installations.
-
Page 11: Product Registration
Product Registration Please take a moment to register and provide us with some important information. Send to: OutBack Power Systems, 19009 62nd Avenue NE, Arlington, WA 98223 USA. Name: ������������������������������������������������������������������������� Address: ���������������������������������������������������������������������� City, State, Zip Code: ������������������������������������������������������������� Country: ���������������������������������������������������������������������� Telephone Number: �������������������������������������������������������������... - Page 12 Worldwide Corporate Offices Headquarter Germany Eastern Europe Russia France and Benelux Hansastrasse 8 russia@alpha-outback-energy.com ee@alpha-outback-energy.com D-91126 Schwabach fbnl@alpha-outback-energy.com Tel: +49 9122 79889 0 Fax: +49 9122 79889 21 Middle East Africa Spain Mail: info@alpha-outback-energy.com africa@alpha-outback-energy.com spain@alpha-outback-energy.com me@alpha-outback-energy.com Alpha and Outback Energy GmbH reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2020 Alpha and Outback Energy GmbH. All Rights reserved. www.alpha-outback-energy.com For more information please visit 00-0085-01-00 REV A...
Need help?
Do you have a question about the FLEXware and is the answer not in the manual?
Questions and answers