Euro Video EVC-TI-BX220D User Manual
  1. Manuals
  2. Brands
  3. Euro Video Manuals
  4. Security Camera
  5. EVC-TI-BX220D
  6. User manual

Euro Video EVC-TI-BX220D User Manual

H.264 network camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1
EVC-TI-BX220D
H.264 Network Camera
Users Manual
www.eurovideo-cctv.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EVC-TI-BX220D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Euro Video EVC-TI-BX220D

Summary of Contents for Euro Video EVC-TI-BX220D

  • Page 1 EVC-TI-BX220D H.264 Network Camera Users Manual www.eurovideo-cctv.com...

  • Page 2: Table Of Contents

    Contents 1. Product Features..................3 2. Accessing the Camera................7 3. The Setup....................13 4. Installation .....................14 5. Camera and Image...................15 6. Audio......................21 7. Live......................23 8. SD Card....................24 8.1 SD Card > Config....................24 8.2 SD Card > Event.....................25 8.3 SD Card > Periodical....................26 9.

  • Page 3: Product Features

    1. Product Features The EVC ZN-XXX is a high performance H.264 network camera, designed for demanding security installations. It delivers crisp, clear images, disclosing every detail, thanks to its top quality 5.0 Megapixel progressive CCD sensor, Megapixel lens and advanced image processing. EVC ZN-XXX features a removable infrared cut filter, which enables color video in high and low light conditions, as well as IR sensitive black/white video at night.
  • Page 4 The EVC ZN-XXX offers a comprehensive set of network security and management features. This includes support for port based network control (IEEE802.1X), which allows the camera to be connected to a network secured with this control, and HTTPS encryption, which provides a secure channel between camera and application.
  • Page 5 1. 8 pin Terminal connector Audio in Audio in (line level), for line-in mono signal (only the left channel is used from a stereo signal) Audio out The Audio output (line level), which could be connected to a public address (PA) system or an active speaker with a built-in amplifier.

  • Page 6: Accessing The Camera

    2. Accessing the Camera Follow the instructions in the EVC ZN-XXX Installation Guide to install the camera. The EVC ZN-XXX could be accessed with most standard operating systems and browsers. The recommended browser is Internet Explorer for Windows with other operating systems.
  • Page 7 2.2 Accessing the camera from the Internet Once installed, the camera is accessible on the local network (LAN). Configure the router/firewall to allow incoming data traffic to access the camera from the Internet. For security reasons this is usually done on a specific port. Please refer to the documentation for router/firewall for further instructions.
  • Page 8 2.5 The Live View page Not all the buttons described below will be visible unless the Live View page has been customized to display them. PC(Client) Speaker PC(Client) Mic Digital Zoom Snap Shot The Snapshot button saves a still image which is currently displayed. Full Screen Stream change: First stream Second stream...
  • Page 9 2.6 Video stream types Motion JPEG This format uses standard JPEG still images in the video stream. These images are then displayed and updated at a rate sufficient to create a stream that shows constantly updated motion. The Motion JPEG stream uses considerable amounts of bandwidth, but also provides excellent image quality and access to every individual image contained in the stream.
  • Page 10 RTP+RTSP This method (actually RTP over UDP and RTSP over TCP) should be your first consideration for live video, especially when it is important to always have an up-to- date video stream, even if some images are lost due to network problems. This could be configured as multicast or unicast.

  • Page 11: The Setup

    3. The Setup The EVC ZN-XXX is configured from the Setup link, which is available on the top left hand side in the web interface. This configuration could be done by: • Administrators, who have unrestricted access to all settings under the Setup link •...

  • Page 12: Installation

    4. Installation The following descriptions show examples of some of the features available in the EVC ZN-XXX. 4.1 Installation Setup Installation mode is for matching the focus with analog output. After connecting the analog monitor output, User can match the focus easily. Please refer Chapter 2.3.

  • Page 13: Camera And Image

    5. Camera and Image The following descriptions show examples of some of the features available in the EVC ZN-XXX. 5.1 Codec These are the tools for adjusting the H.264, MJPEG settings and controlling the video bit rate. Motion JPEG This format uses standard JPEG still images in the video stream. These images then are displayed and updated at a rate sufficient to create a stream that shows constantly updated motion.
  • Page 14 Using H.264, it is also possible to control the bit rate, which in turn allows the amount of bandwidth usage to be controlled. CBR (Constant Bit Rate) is used to achieve a specific bit rate by varying the quality of the H.264 stream. While using VBR (Variable Bit Rate), the quality of the video stream is kept as constant as possible, at the cost of a varying bit rate.
  • Page 15 < Output resolution table for 2M(Full HD) series > Second First Stream Stream 1920x1080 1920x1080(wide) 1280x1024 1280x720 1280x720(wide) 640x480(A) 1024x768 640x480 704x576 704x576 704x480 704x480 640x480 640x480 352x288 352x288 352x240 352x240 320x240 320x240 These features are subject to change without notice. <...
  • Page 16 < Output resolution table for EVC-XXX-0350 series > Second First Stream Stream 704x576 704x576 704x480 704x480 640x480 640x480 352x288 352x288 352x240 352x240 320x240 320x240 These features are subject to change without notice. In case 1280x720(wide) mode, the second stream is apect-ratio-corrected. 5.2 Camera www.eurovideo-cctv.com...
  • Page 17 5.2.1 Exposure Control Enable AE (Auto Exposure) ON: Use these settings to control full automatic exposure control. Some sub menus ( AGC Gain, e-Shutter Speed) will be disabled. OFF: Use these settings to control exposure manually. To compensate for poor lighting conditions, you could adjust the Color level, Brightness, Sharpness, Contrast, Exposure control, and DC-Iris.
  • Page 18 The EVC ZN-XXX Network Camera could be set automatically to identify the light source used and compensate for its color. Alternatively, the type of light source could be set manually. The configuration of the video image would affect the camera’s overall performance, depending on how it is used and on the available bandwidth.

  • Page 19: Audio

    6. Audio The EVC ZN-XXX could transmit audio to other clients, using a connected external microphone and could play audio received from other clients via connected speakers. This section describes how to configure the basic audio settings for the EVC ZN-XXX, such as setting the communication mode, adjusting the sound levels in the microphone and speakers connected to the camera.

  • Page 20: Live

    7. Live EVC ZN-XXX could support 10 simultaneous users. In case of multicast, EVC ZN-XXX could support unlimited number of users. If supported on the network, consider using multicasting, as the bandwidth consumption will be much lower. Viewer Setup LiveView Protocol RTP Unicast (UDP) / RTP Multicast (UDP) / RTP over RTSP (TCP) Buffering Time (frame based)

  • Page 21: Sd Card

    8. SD Card 8.1 SD Card > Config SD Card Configuration This is setting page relating to save still shot in Micro SD card. It could not be used when Installation mode is on. Please set the first stream 1280x720 or 1280x720(wide) in Video-> Codec setting and second stream to MJPEG or None.

  • Page 22: Sd Card > Event

    8.2 SD Card > Event Event SD Writing It is setting page for storing still shot on the Micro SD card when there is events such as Alarm In and Motion detection. This could not be used in installation mode on status. Please set the first stream 1280x720 or 1280x720(wide) in Video->...

  • Page 23: Sd Card > Periodical

    8.3 SD Card > Periodical Periodical SD Writing It is setting page to save the still shot in the Micro SD card periodically. It could not be used when the Installation mode is on. Please set the first stream 1280x720 or 1280x720(wide) in Video->...

  • Page 24: Ftp

    9. FTP 9.1 FTP > Config Server Configuration It is setting whether to use the provided FTP Server to download the configuration set on the SD Card menu remotely. When it is set as Enable, the FTP client could download the saved content without getting the SD Card.

  • Page 25: Ftp > Event

    9.2 FTP > Event Event FTP Sending It is setting page to transmit the still shot to the FTP server at remote sites when event such as Alarm In and Motion detection happens. It could not be used when the Installation mode is on.

  • Page 26: Ftp > Periodical

    9.3 FTP > Periodical Periodical FTP Sending It is setting page to transmit the still shots periodically to the FTP server of remote sites. Before using the FTP, turn off the Installation mode. Please set the first stream 1280x720 or 1280x720(wide) in Video->...

  • Page 27: Event

    10. Event 10.1 Event > Alarm Port Alarm Input - Used for connecting external alarm devices and triggering images for specific alarm-based events. The input is typically connected to a motion detector or any other external security device, and images could be uploaded whenever the detector is activated.

  • Page 28: Event > Motion

    10.2 Event > Motion Motion Detection Motion detection is used to generate an alarm whenever movement either occurs or stops in the video image. A total of 10 windows could be configured. Configuring Motion Detection 1. Click Motion Detection in the Event Config menu. 2.

  • Page 29: Event > Mapping

    10.3 Event > Mapping It is possible to define conditions that would cause the camera to respond with certain actions. A triggered event happens as a result of a trigger, which could be motion detection or an external alarm input. For example, Alarm out events could be triggered by video motion detection or alarm in.

  • Page 30: Network

    11. Network 11.1 Network > IP Setup Network Settings Click the Setup > Network > IP Setup to see the current network settings. IP Address Configuration - The EVC ZN-XXX supports both IP version 4 and IP version 6 (IPv6 will be supported in V3.00).
  • Page 31 the IP address changes and you lose contact with the camera. Configure the options for notification of IP address change (under Services) to receive notification from the camera when the IP address changes. EVC Internet Dynamic DNS Service - The EVC Internet Dynamic DNS Service could provide your EVC product with its own URL (web address), which could then be used to access it over the Internet.

  • Page 32: Network > Service Port

    11.2 Network > Service Port Service Port HTTP port- The default HTTP port number (80) could be changed to any port within the range 1-65535. This is useful for simple port mapping. RTSP port- The RTSP protocol allows a connecting client to start an H.264 stream. Enter the RTSP port number to use.

  • Page 33: Network > Rtp

    11.3 Network > RTP RTP port range These settings are the IP address, port number, and Time-To-Live value to use for the video stream(s) in multicast H.264 format. Only certain IP addresses and port numbers should be used for multicast streams. www.eurovideo-cctv.com...

  • Page 34: Network > E-Mail

    11.4 Network > E-mail Enter the host names or addresses for your mail servers in the fields provided, to enable the sending of event and error email messages from the camera to predefined addresses via SMTP. www.eurovideo-cctv.com...

  • Page 35: Network > Ddns

    11.5 Network > DDNS The EVC Internet Dynamic DNS Service could provide your EVC product with its own URL (web address), which could then be used to access it over the Internet. The product could be unregistered from the service at any time. To do this click Network > DDNS and turn the DDNS off.

  • Page 36: Network > Upnp

    11.6 Network > UPnP www.eurovideo-cctv.com...

  • Page 37: System

    12. System 12.1 System > User Access the camera and the Configure Root Password dialog appears. Enter the User name: ADMIN and password is 1234. To changed password or add a user click SETUP > SYSTEM > USER. Fill the User ID, Password and E-mail server.

  • Page 38: System > Date & Time

    12.2 System > Date & Time Date & Time Format - specify the formats for the date and time (12h or 24h) displayed in the Live View video streams. Use the predefined formats or use your own custom date and time formats.

  • Page 39: System > Maintenance

    12.3 System > Maintenance System name- Factory default- To reset the camera to the original factory default settings, go to the System > Maintenance web page or use the Control button as described below: Using the Web Page 1. Go to SETUP > System > Maintenance.
  • Page 40 5. When the Status Indicator changes to Green (which may take up to 1 minute), the process is complete and the camera has been reset. The unit will now have the default IP address from a DHCP server. Use “ADMIN tool” to find and connect the camera unit. Save User Data- System settings can be saved to a PC.

  • Page 41: System > Information

    12.4 System > Information System information: After updating firmware, you could confirm the F/W version at this page. www.eurovideo-cctv.com...

Table of Contents