Advertisement
H300
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H300.
FOR MORE INFORMATION ON USING
YOUR MOTOROLA H300
Visit us at www.hellomoto.com/bluetooth and
click Support.
SUPPORT
If you need more help, contact us at
1-877-MOTOBLU.
TURNING ON AND OFF
To turn your headset on, press and hold
the Call button until the indicator light
flashes. Then, release the button.
To turn your headset off, press and hold
the Call button until the indicator light
flashes rapidly and then turns off.
To conserve battery power, turn off your
headset when you don't plan to use it for
a while.
Call
Button
MAKING CALLS
Function
Action
Make a voice dial call
Tap the Call button
and speak the
name after the tone
End a call
Tap the Call button
Receive a call
Tap the Call button
Reject a call
Press and hold the
Call button until you
hear a beep
Redial last call
Press and hold the
Call button until you
hear a beep
Answer a second
Press and hold the
incoming call
Call button (places
first call on hold)
Note: Your H300 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
WEARING THE
HEADSET
1
Open the earhook.
2
Loop the earhook over your ear.
3
Press the headset to your ear.
MAKING CALLS
CONTINUED
Function
Action
Toggle between two
Press and hold
active calls
the Call button
Join a 3-way call
Press and hold
both Volume buttons
Put an active call on
Press and hold the
hold or resume a call
Call button until you
on hold
hear a beep
Transfer a call from the
Tap the Call button
phone to the headset
Disable or enable the
Press and hold
indicator light
both Volume
buttons for 3 to 4
seconds
Mute or unmute a call
Tap both Volume
buttons
Note: Some features are phone/network dependent.
CHANGING FOR USE
ON OTHER EAR
You can wear your H300 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1
Open the earhook 90
degrees from the
headset.
2
Gently lift and pull the
1 Open Earhook
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
2 Pull Earhook Up
remove it.
040059o
3
Flip the headset over.
4
Hook the bottom of the
Hinge Pin
earhook onto the lower
hinge pin, then lift and pull
the top of the earhook over
the upper hinge pin.
INDICATOR LIGHTS
The indicator lights provide information about
your headset status.
Indicator Light
Headset Status
Off
Power off
On (steady)
Pairing mode
10 rapid flashes
Pairing successful
Slow pulse
Connected
(on a call)
Quick flash
Standby
(not on call)
Note: After 5 minutes of inactivity, the light stops flashing
to conserve power, but the headset remains in standby
mode.
CHANGING VOLUME
BUTTON ORIENTATION
If you change your headset to wear on the
other ear, you can also change the
orientation of the Volume buttons.
1
Turn the headset power off.
2
Press the Call button and the Volume
button you want to assign as the
"volume up" button until the blue
indicator light flashes twice.
The headset power turns on.
Call
Volume
Button
Buttons
AUDIO TONES
The audio tones provide information about your
headset status.
Audio Tone
Headset Status
Single high tone when
Volume at minimum
pressing volume button
or maximum
Five rapid high tones
Low battery
repeated every 60 sec.
No audio indications;
Out of range
deteriorating quality
Ring tone
Incoming call
Single high tone
Pairing confirmation
Single low tone
Voice activation
Dual high/low tone
Voice tag not
recognized
Single high tone
End call
Low to high tone
Phone network
not available
Two ascending tones
Mute enabled
Two descending tones
Mute disabled
Hide quick links:
Advertisement
