Your Phone 3 PAIR Your Headset 3 PAIR CONTINUED Your Phone 4 TEST AND USE USING YOUR H390 TURNING HEADSET ON AND OFF EARBUDS AND YOUR HEADSET WEARING THE HEADSET CHANGING FOR USE ON OTHER EAR CHANGING VOLUME BUTTON ORIENTATION...
BEFORE YOU BEGIN Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions. Take a moment before you get started to familiarize yourself with your new H390 Headset. Volume Earhook Buttons Speaker Call Button...
Port Verify slide switch is in the off position (toward the charging port). Plug the Motorola charger into the end of the headset. The indicator light turns red or yellow when the battery is charging. It may take up to 1 minute for the indicator light to turn on. When the headset’s battery is fully charged (about 2 hours), the indicator light turns green.
Select Change. Scroll to On. Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn the feature off. Note: These steps are for most Motorola phones. For other phones, see your phone’s user’s guide.
3 PAIR Your Headset Before you can use your headset, you must pair (link) it with your phone. Step A - ENSURE HEADSET IS IN PAIRING MODE Power on headset by sliding the Power switch towards the microphone to initiate easy pairing.
Select OK. When your headset successfully pairs and connects with your phone, the indicator light changes from steadily lit to flashing blue and purple. Note: These steps are for most Motorola phones. For other phones, see your phone’s user’s guide.
4 TEST AND USE Your phone and headset are now paired and ready to make and receive calls. To make a call: Place the headset over your ear. On the phone, dial the number you want to call and press SEND key on your phone.
USING YOUR H390 Note: If desired, your headset can be restored to original factory settings. This action will erase all pairing information stored in your headset. Thus, you will need to pair your phone and headset again (see step 3).
TURNING HEADSET ON AND OFF To turn your headset on, slide the switch toward the microphone. The indicator light flashes blue three times, then flashes in blue and purple (if connected with a device) or is steadily blue (if ready to be paired). To turn your headset off, slide the switch toward the charging plug.
EARBUDS AND YOUR HEADSET Your H390 headset is supplied with multiple earbuds. The earbud is fitted onto the end of your headset’s earpiece speaker, and placed onto your ear when using your headset. Your headset’s performance is greatly dependent upon achieving a good fit on your ear.
CHANGING FOR USE ON OTHER EAR You can wear your H390 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear: Gently lift and pull the top of the earhook up and off speaker stem, as shown.
CHANGING VOLUME BUTTON ORIENTATION You can also change the orientation of the volume buttons on your headset. Turn the headset power off. Press and hold the Volume button you want to assign as the “volume up” button and slide the switch toward the microphone. The indicator light flashes blue three times, then steady blue.
QUICK BATTERY CHECK When not on a call, you can check your headset’s battery charge level by pressing and holding both Volume buttons. The indicator light displays charge status for 5 seconds. See below for details on indicator light and charge status. Headset Indicator Talk Time Less than 2.5 hours...
Use phone to answer (follow your phone’s instructions) call Note: Your H390 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone’s user’s guide for more information. Note: Some features are phone/network dependent.
INDICATOR LIGHT With the Charger Plugged In Headset Indicator Headset Status Charging (battery level less than 70% charge) Yellow Charging (battery level more than 70% charge) Green Charging complete...
INDICATOR LIGHT With No Charger Plugged In Headset Indicator Headset Status Power off Three blue flashes Powering on/off Steady blue Pairing/connect mode Rapid blue/purple flashes Connection successful Quick blue flash Incoming/outgoing call Slow blue pulse Connected (on a call) Slow blue flash Standby (not on a call) Slow red flash Idle (not connected to phone)
AUDIO TONES Audio Tone Headset Status Ascending tone Powering on Two descending tones Powering off Ring tone Incoming call Two short tones when Volume at minimum pressing Volume button or maximum High/low tones Low battery repeated every 60 sec. No audio indications; Out of range deteriorating quality Two ascending tones...
TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode.
1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada) MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products.
0860 10 10 39 Turkey 0212 317 45 95 This symbol on a Motorola product means the product should not be disposed of with household waste. Please do not dispose of mobile telephones or electrical accessories, such as chargers or...
The above gives an example of a typical Product Approval Number. You can view your product’s Declaration of Conformity (DoC) to Directive 1999/5/ EC (to R&TTE Directive) at www.motorola.com/rtte. To find your DoC, enter the product Approval Number from your product’s label in the “Search” bar on the...