Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Faro EVA
Summary of Contents for Faro EVA
-
Page 2: Table Of Contents
AUTO-ON SETTING ..............................................8 SWITCHING ON/ OFF THEIA ..........................................8 REMOTE CONTROL ..............................................8 SYNCRO MODE WITH FARO ROOM LIGHT ..................................... 9 PREVENTIVE MAINTENANCE AND ROUTINE CHECKS ................................10 CLEANING AND DISINFECTION ........................................... 11 CLEANING OF THE REFLECTING PARABOLAS ..................................11 CLEANING AND DISINFECTION OF THE HEAD .................................. -
Page 3: Symbols Used
USER MANUAL - EN Dear Customer, FARO hopes you enjoy your work with the new high quality light. For safe work and to take full advantage of the performance of the product, read carefully this manual before using the device. -
Page 4: Intended Use
USER MANUAL - EN Symbol Description Serial Number Can be sterilized with heat at 134°C Use the device at a temperature between 10°C and 40°C Use the device at pressure between 80 kPa and 106 kPa Use the device at relative humidity between 30 RH and 75RH Symbol to adjust light intensity Symbol to switch on/off the light Symbol to switch on/off the light on the rear arm (Alya with Theia Tech) -
Page 5: Description Of The Product
The device is available in two main product variants: EVA with light source at 5000 K with “Sunlight” Spectrum EVA with Tunable White light source (4000 K, 5000 K, 5700 K, Composave setting (2700 K)) selectable by the operator. These main variants can be supplied with:... -
Page 6: Description Of Common User's Interface
USER MANUAL - EN DESCRIPTION OF COMMON USER’S INTERFACE Knob of the handle Joystick Indicator Strip Button for pairing and Tk change Sensor (alternative to Joystick) Sterilizable Handle Button for Theia Tech INSTRUCTION FOR USE The device must be cleaned before use (see Device Cleaning paragraph). Caution Do not use the device in flammable or explosive environments Simultaneous use of the light with electro-surgical devices can cause malfunctioning (flickering, no command, etc) -
Page 7: Changing Color Temperature On Tunable White Version
USER MANUAL - EN Sensor - Increase and decrease light intensity Bring the hand towards the sensor up to 2 cm and keep this distance until the desired light intensity is reached Acoustic signal: 1 beep at command Maximum intensity reached: 2 beeps Minimum intensity reached: 1 beep in sensor version the light intensity changes continuously decreasing until minimum and... -
Page 8: Composave Setting On Tunable White Version
USER MANUAL - EN COMPOSAVE SETTING ON TUNABLE WHITE VERSION Composave setting allow the user to work with restorative material avoiding their polymerization. Select the composave setting as described below: Joystick version option 1 Joystick version option 2 Visual information At the command selection of compo save a wigwag beep will be heard. -
Page 9: Syncro Mode With Faro Room Light
On release, a sound signal (Beep) will be heard and the blue LED on the Room Light lamp will go out to indicate that synchronization has been disabled. When the Faro Room Light is synchronized with the Dental Light the blue LED on the room light is lighted in steady mode. If the LED is off, the synchronization is not active. -
Page 10: Preventive Maintenance And Routine Checks
USER MANUAL - EN PREVENTIVE MAINTENANCE AND ROUTINE CHECKS Only Service Engineer are allowed to perform corrective Maintenance and replacement of any part of the device, according to Manufacturer’s Service Manual. Checks Frequency Procedure Responsible No plays or space gaps between the Yearly Service junction points (points 1, 2, 3, 4) -
Page 11: Cleaning And Disinfection
It is forbidden to directly spray any chemical substance on the device. It is forbidden the use of wet wipes without rinsing. Faro tested and suggests the use of the following disinfectants, for plastic parts and metal parts: Durr FD366 Sensitive Faro Perflex Advanced Water-alcohol based disinfectants with 70% isopropyl alcohol or ethanol are suitable. -
Page 12: Troubleshooting
USER MANUAL - EN TROUBLESHOOTING ERROR LIST Error Description Indicator Strip Acoustic indication First sector blinking. Open Led channel 1 Colour set-up: RED 3 short beeps repeated 3 times First and second sectors blinking OPL Open Led channel 2 Colour set-up: RED High temperature on the Led group All sectors blinking together. -
Page 13: Storage And Transportation: Environmental Conditions
USER MANUAL - EN (*) Typical optical values subjected to tolerances Measurement performed at 700 mm distance. Contact Faro for the correct procedure for the measurement. STORAGE AND TRANSPORTATION: ENVIRONMENTAL CONDITIONS The device in the original packaging can be transported and stored for a maximum period of 15 weeks if the following environmental conditions are met: Environmental temperature from -20°C to + 70°C... - Page 14 USER MANUAL - EN Edition 1.0 April 2020 Pag. 14 di 14...
Need help?
Do you have a question about the EVA and is the answer not in the manual?
Questions and answers