JLab Epic Sport 2 - Wireless Earbuds

Also See for Epic Sport 2:

Manual (4 pages)

Table of Contents

Contents

1 BLUETOOTH PAIRING
2 CHARGING
3 BUTTON FUNCTIONS
4 EQUALIZER MODES
5 VOICE PROMPTS
6 FITTING
7 CABLE CLIP USE
8 CONNECTION TROUBLESHOOTING
9 Documents / Resources
- 9.1 References
- 9.2 Download manual

JLab Epic Sport 2 - Wireless Earbuds

BLUETOOTH PAIRING

Turn on the Bluetooth in your device settings.
Press and hold button for 8 seconds. Release. Light will blink red and blue to indicate pairing mode.
Select "JLab Epic Sport" in your device settings to connect.
Light will slow blink blue when Bluetooth is paired.

RECURRING USE
Once JLab Epic Sport 2 has initially paired to your device, the earbuds will auto-connect to your Bluetooth device when powered back ON. (Follow BUTTON FUNCTIONS instructions)

CHARGING

Open USB door and connect the cable to a computer or 5v (or less) power source to charge.
CHARGING

BUTTON FUNCTIONS

VOLUME UP: Quick press
TRACK FORWARD: Press & hold 2 seconds
POWER ON: Press &hold 3 seconds
POWER OFF: Press & hold 5 seconds
PLAY / PAUSE / ANSWER / HANG UP: Quick press
BLUETOOTH PAIR: Press & hold 8 seconds (see Bluetooth Pairing)
ACTIVATE GOOGLE / SIRI: Click twice
VOLUME DOWN: Quick press
TRACK BACKWARD: Press & hold 2 seconds

EQUALIZER MODES

EQUALIZER MODES
Quick press both buttons for different EQ settings
(Epic Sport 2 will cycle 3 EQ settings)
JLab SIGNATURE (One Beep)
JLab C3™ signature sound with amplified bass and vocals
BALANCED (Two Beeps)
Even sound with no additional enhancements
BASS BOOST (Three Beeps)
Amplified bass and sub-bass

VOICE PROMPTS

"HELLO" = Power is ON.
"BATTERY FULL" = 100-75%
"BATTERY MEDIUM" = 75-25%
"LOW BATTERY" = Less than 25%
"READY TO PAIR" JLab Epic Sport 2 earbuds are ready to connect to your Bluetooth device.
"YOU'RE CONNECTED" JLab Epic Sport 2 is connected to your Bluetooth device and ready for use.
"GOODBYE" = Power turning OFF.

FITTING

Try various ear tips and Cush Fins to find the best fit.
Rotate the earbud into ear canal and bend the Memory Wire to desired position.

CABLE CLIP USE

Attach optional cable holder to tighten or loosen the cable during use.
Insert the optional cable clip to the back of the cable holder.
Open the cable clip and attach to apparel.

CONNECTION TROUBLESHOOTING

I DO NOT SEE JLAB EPIC SPORT IN MY DEVICE

Turn Bluetooth off and then back on in device settings.
If you still do not see JLab Epic Sport, repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.

JLAB EPIC SPORT 2 DOES NOT RECONNECT TO MY DEVICE AFTER POWERING ON

In device settings, forget the JLab Epic Sport.
Turn Bluetooth off then back on in device settings.
Repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.

BLUETOOTH IS CONNECTING TO AN UNWANTED DEVICE
Note: The JLab Epic Sport 2 can remember up to 8 devices. It will try to auto-connect to last device used.

If you have more than one device that was connected to JLab Epic Sport 2, turn OFF Bluetooth on unwanted devices and turn ON Bluetooth on chosen device.
Press and hold button for 8 seconds. Release. Light will blink red and blue to indicate pairing mode.

Avoid getting moisture or liquids into the tip of the earbuds or charging port.
Avoid extreme heat, cold, and humidity.
Avoid dropping or crushing the earbuds, stressing the cable by rapid pulling or extreme force, or bending the cable at a sharp angle.
Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
If you experience regular discomfort while using this product, discontinue use and consult your physician.
We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.

Shop products | Product alerts | Burn-in your headphones
JLab Audio + Burn-in Tool

JLABAUDIO.COM

YOUR WARRANTY
All warranty claims are subject to JLab Audio authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at support@jlabaudio.com or visit jlabaudio.com/contact