Page 1
LCD TV PB20C THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHANGES, ERRORS...
1. SPECIFICATIONS FOR LCD TV 1-1 GENERAL SPECIFICATIONS 20.1” screen Feature SVGA ( 800 x 600 ) Resolution High Brightness ( 500 cd/m High Contrast Ration ( 500:1 ) Wide Viewing Angle ( 160 H / 160 V ) Built-in Full channel Tuner with Nicam, Teltext. Graphic (VGA) PIP(Video on Graphic) Items...
The LCD TV will contain a main board (include audio), a switching power board (include an inverter board), an IR board, a function keyboard, and an Ear phone board. The main board and power board will house the flat panel to control logic I2C bus, DDC, brightness control logic for LCD panel, DC-DC conversion to supply the appropriate power to the whole board and transmitting TTL level signals into LCD Module to drive the LCD display circuit.
3. D-SUB PIN DISTRIBUTION This procedure gives you instructions for installing and using the LCD TV display. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduct ground.
Page 7
VIDEO Adjust 1. CONTRAST, BRIGHTNESS, COLOUR and TINT are adjusted from 0 to 100. 2. BLACK LEVEL is adjusted from 0 to 100. 3. SHARPNESS is adjusted from -5 to+5. You can adjust picture contrast, brightness, color, tint and sharpness to the levels you prefer. 4.
Page 8
1. VOLUME is adjusted from 0 to 100. 2. BASS and TREBLE are adjusted from 0 to 100. You can adjust picture Volume, Bass and Treble to the levels you prefer. When adjust any item sub-OSD will show up like this. 3.
Page 9
1. BLUE SCREEN for when no video input screen will be blue or blank. If it’s ON, the screen will be in blue. If it’s OFF, the screen will be blank. Preset is ON. 1. LANGUAGE for different language OSD MENU. Preset is English. 2.
Page 10
Colour for you can adjust the colour temperature you prefer. COLOUR 1. PIP for turn on / off small picture function. 2. POSITION for change the position of small picture. 3. SOURCE for select video source of small picture. SOUND for select audio source form MAIN (PC) or SUB (Video). Input Source Select: Press repeatedly Source button to select TV, AV1, SCART, S-VIDEO or PC mode.
Page 11
USE OF THE REMOTE CONTROL USE OF THE REMOTE CONTROL DISPLAY POWER: (1) Display Channel number Press to turn on/off the TV. when use RF input. The TV is never completely (2) Display input source when powered off unless it is use other input except TV physically unplugged.
Teletext is an information service organized like a magazine, which is provided by some TV stations in addition to regular television broadcasting. TELETEXT Press TELETEXT. The Teletext screen appears. To turn off the Teletext mode, press TELETEXT again. Press MIX to superimpose the teletext over a normal broadcast picture.
Press MENU key to show OSD window or exit, Up / Down key to done the function selection, And + / - key to done the adjustment. There is a wide range of video and audio equipment that can be connected to your TV. The following connection diagrams show you how to connect them.
5. TROUBLE SHOOTING CHART 5-1.Panel Control Circuit: No Display Check CN101 pin 42-45 Replace panel or FFC is 5V and signal on pin cable to panel 35,37,39,40,25-28,30-33,15- 18,20-23,5-8,10-13 Check U300 Output to CN101 relative circuit and Replace L118, C137 CN101 VCC at Q300, Q301, L309 (5V) Check U300...
5-7 Video Control Block: Note: 1、If Replace “MAIN-BOARD” , Please re-do “DDC-content” programmed & “WHITE-Balance”. 2、If Replace “ POWER-BOARD INVERTER” only, Please re-do “ WHITE-Balance” 3、Please re-install program before you do change any component.
6. White-Balance, Luminance adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. Before started adjust white balance, please setting the Chroma-7120 MEM. Channel 1 to 9300 colors, MEM. Channel 2 to 6500 color, and MEM. Channel 3 to 9300 colors, (9300 parameter is x = 283 ± 15, y = 297 ± 15, Y = SPC. ± 7 cd/m2;...
Page 21
B.Adjust 6500 color-temperature: 1. Set the Contrast of OSD function to 45 and Adjust Brightness to chroma-7120 Y>230 cd/m 2. Switch the chroma-7120 to RGB-mode (with press “MODE” button) 3. Switch the MEM.channel to Channel 02 (with up or down arrow on chroma-7120) 4.
9.2 POWER BOARD SCHEMATIC DIAGRAM R 919 47_1/2W _ M R 920 C 913 47_1/2W _ M 102P _500 V 5Vout D 910 F902 MOS P E C 2010 0 5A /24 V /1206 12Vout L903 TO INVERTER T901 73L-253-91L P Q26 /22.5 FB 902 R 906...
Page 41
5Vout L101 Q1 01 FB 101 22U H BE AD C1 01 D1 01 D1 02 C1 06 C1 07 0.1UF 1000u F/16V SI4431DY-T1 SR24 SR24 1000u F/16V R1 01 C 103 10N F C1 05 100P F(NPO) LM3485 C1 04 PGAT E IC102 R 102...
Page 42
C N20 1 C2 0 1 2 7 P/ 3 KV Q2 0 1 SI 4 4 3 1 OR AO4 4 1 1 R 201 4.7K Q 202 12V out S S T3 904 L 2 0 1 D 201 Q2 0 3 1 5 0 UH (6 0 -5 2 ) C 202 0.01U F...
Page 43
+12V C C V _RE F R 298 V _S E N S O R _4 D 221 1N 4148 V _S E N S O R _1 R 256 D 222 1N 4148 300K R 299 R 254 R 255 V _S E N S O R _5 R 293 300K V _S E N S O R _2...