Page 1
Thank you for using TOP-PCVIEW series of M2I corporation. Please read this manual carefully to know installing, wiring, operating, servicing and inspecting this equipment. 1 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Incorrect wiring could result in fire, damage or malfunctions. Tighten the terminal screw with the specified torque. If the screws of terminal are loose, it could result in 4 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 5
■ All field-wiring connections to this unit shall be from Limited Voltage. Limited below 24Vdc isolated secondary source with an output fuse, or Class 2. 5 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
- Windows 10 IoT 1809 LTSC 64bit 한글/영문 Common TOPVIEW License USB USB Dongle Inserted Common * A basic O/S of Celeron and 4th Core-i3 product is WES7. 8 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
TOP-PCVIEW19 497 x 316 x 94.8 Cooling System Natural air circulation Case Material AL(Aluminium) Chapter 4 Parts Names and Functions 4.1 TOP-PCVIEW10**** 9 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
(1) The Size of Panel Cut (Mounting Place) Making the Panel Cut (Mounting Size) per each TOP PC Series as below Table, Before Installation. 13 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 14
Tighten the screw to 0.5Nm. Caution: Front protection (IP) will not able to work when clamp is not tightened in 0.5N.m power. 14 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
(2) Gender Remove: Hold down the button below and pull back the USB gender. (3) Close the cover: Close and slide the cover of the connector. * Locker type USB cover is required for front USB gender use. Please contact M2I Corporation. 15 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Serial Port COM1 COM2 COM3 COM4 Manufacturer status RS-232C RS-232C RS-485 RS-485 RS-232C RS-232C Available settings Not available Not available RS-422 RS-422 16 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 17
9Pin male Output Data Terminal Ready Signal Ground Output Data Set Ready Output Request to Send Input Clear to Send Input Ringing Indicator 17 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
5.0V@500mA 1.5m (Cable from M2I is recommended. Meet the length limit for other Cable Length cables.) Connector type Micro USB B, Female 19 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
When doing ground, please refer to the followings. (2) The ground should be the exclusive ground. The ground should be type 3 ground (ground resistor is less than 100Ω) 20 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
If there is no recovery file on the right, select [Browse Backup]-> [Acronis Secure Zone]-> Restore File on the right side of the screen. 21 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 22
5) If "MBR and Track 0" is deselected, the [Partition C Settings] and [Partition D Settings] menus will be created additionally. [Partition C Settings] * Partition Location (Required): Specify as (C:). * Partition type: set "primary, partition active". 22 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 23
Please be careful when restoring all previously saved data will be deleted. If you touch ‘Factory Reset’ button, it will start the recovery. 23 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
The physical memory is called an overlay the information related to the write operation on the overlay will be accumulated. The Product can be set easily by built-in applications. 24 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 25
The default status of EWFManager is set to DISABLED. Set to ENABLED. (4) It turns to ENABLED after re-boot. (5) Check the ‘ENABLE’ is adopted. 25 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
64 GB, the maximum storage capacity of RAID 1 is set to 64GB. (1) BIOS Setting To use RAID, you need to change the SATA mode to RAID in BIOS as below. 26 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 27
Confirmation window before RAID configuration. Press the "Y" key. The RAID configuration is completed. When the configuration is completed, exit with EXIT and install Windows. 27 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 28
To delete the information on the RAID configuration disk, use menu 3 (Reset Disks to Non-RAID). This process should be used again when using AHCI mode again. Select the disk you want to reset and press "Enter". 28 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 29
RAID configuration (RAID1) that you created previously. (It is also possible with the intel RST utility of the OS) After the addition, you need to rebuild from Intel RST utility in OS. 29 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 30
If the disk is broken or there is a problem with the connection, the disk with the problem as shown below is displayed. 30 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
Page 31
4) After the recovery, the recovery solution will be disabled. Be sure to click "Tools & Utilities" - "Activate "Acronis Startup Recovery Manager" - "Activate". 31 / 34 I Corporation 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
(2) Only the authorized worker from M2I Corporation can check and repair problems related to malfunction of the machine. (3) If the problem cannot be solved at the installation site, the equipment can be collected and moved to M2I Corporation.
Copyright: - When using M2I equipment, thoroughly read this datasheet and associated manuals introduced in this datasheet, also pay careful attention to safety and handle the module properly. - Store this datasheet in a safe place so that you can take it out read it whenever necessary.
Need help?
Do you have a question about the TOP-PCVIEW Series and is the answer not in the manual?
Questions and answers