Page 1
OWNER’S MANUAL Model number #700725 Subframe for Compact Tractor #700738 Driveline for Compact tractor with mid PTO 1-15 Splines #700945 Bracket kit for B1905H, T194H and T224 #700946 PTO drive mec. (short) For compact tractor BERCO Hydraulic lift subframe and drive mechanism For tractor TYM 194H / 224 &...
Introduction Introduction To the purchaser This new accessory was carefully designed to give years of dependable service. This manual has been provided to assist in the safe operation and servicing of your attachment. All photographs, illustrations and information in the manual may not necessarily depict the actual models or attachments, but are intended for reference only and are based on the latest product information available at the time of publication.
Important safety information Important safety information Safety alert symbol/Signal words/Safety messages These are common practices that may or may not be applicable to the product described in this manual. SAFETY ALERT SYMBOL THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
Page 5
Important safety information • • Exercise extreme caution when operating on or Handle fuel with care, it is highly flammable and crossing gravel drives, walks or roads. Stay alert vapors are explosive. for hidden hazards such as traffic, fences, trees, a) Extinguish all cigarettes, cigars, pipes and other buildings, wires, etc.
Page 6
Important safety information TRANSPORT Remove all tools and unused parts from equipment before operation. • • Review Transport Safety instructions in the Disconnect battery ground cable (-) before vehicle manual before moving or hauling. servicing or adjusting electrical systems or •...
Important safety information Safety decals Read and understand all instructions/explanations noted on decals or/and in the “Safety Decals” section • Keep the safety decals clean and visible • For decal location see part list section of this manual • Replace decals if decals are missing or illegible •...
Assembly & initial configuration Assembly & initial configuration Tractor requirements This subframe is designed to be installed on a TYM 194H / 224 or Branson 1905H only. The front loader must be removed. WARNING To avoid serious injury or death caused by vehicle overturn: Operate only with tractor equipped with an approved rollover-protective structure (ROPS) or ROPS cab and...
Assembly & initial configuration Accessory assembly Note 2 : it may be necessary to drill the holes on the tractor with a 3/8 "diameter drill bit if the bolt is too difficult to fit. WARNING Installation of the spacers and support THIS ACCESSORY AND ALL OPTIONS ARE HEAVY! plates: To avoid risk of strain injury, NEVER lift the accessory or...
Assembly & initial configuration Drive mechanism preparation Installation of the hydraulic connectors: Assemble the drive mechanism #700946 with mounting plate #700945 Install the hydraulic connectors on the hose following the instructions of the connector assembly #700644) Use 4 bolts 1/2 x 1-1/2 (item 1) with nylon insert lock nut 1/2 (item 2) to assemble mount plate (item A) with drive mechanism (item B).
Hook and un-hook accessory Hook and un-hook accessory Hooking the accessory Remove front guard Remove 4 bolts M12 (item 1) and guard (item2) from Note: the front loader must be removed from the tractor tractor (item 3). Subframe preparation: A. Remove the pins (items 1) and the cotter rings (item 2) and set aside to use them in the next step.
Hook and un-hook accessory Attaching the subframe: Raise the parking stand (item 1) removing the pin (item 2) and its cotter ring. Then replace the pin. A. Steer the tractor steering wheel fully to the left to allow insertion of the rear pin B.
Page 13
Hook and un-hook accessory 1. Route hydraulic hose to the tractor hydraulic quick C. Remove accessory installed on the subframe. (see the manual of the concerned accessory). connect in a way to avoid damage to hose and allow D. Follow the instructions for installation of the movement of any components.
Operating instructions Operating instructions Safety precautions DANGER To avoid serious injury or death caused by vehicle DANGER overturn: To avoid serious injury or death : The accessory can affect vehicle handling • • When accessory is installed on the subframe avoid Always follow all safety precaution in the important any steep move safety information section of this manual.
Operating instructions Operating instructions Pre-Start Operation Always inspect the accessory before starting use. See the section "Maintenance and lubrication" Vehicle shut-down procedure Always shut down vehicle before dismounting 1. If engaged, disengage PTO 2. Park on level surface, engage park brake, lower attachment to the ground, turn off engine, and remove key to prevent unauthorized starting.
Troubleshooting Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Accessory does not lift or lower Dirt in the oil Change hydraulic oil Raises too slowly Damaged bushing Replace the bushing...
Maintenance & Lubrication Maintenance & Lubrication WARNING To avoid serious injury or death : • Always follow all safety precautions in the important safety information section of this manual. • Follow all instructions and safety precautions in your vehicle manual and any other related accessory manual.
Dismount and storage Dismount and storage Long-Term Storage Transportation Follow unhooking instruction in the section “Hook-up WARNING and Unhook Accessory” of this manual. To avoid serious injury or death : • Clean the accessory When travelling on public roads, use SMV sign, clean •...
Page 26
Parts breakdown & Part list NOMENCLATURE ET LISTE DES PIÈCES PARTS BREAKDOWN & PARTS LIST ARBRE À CARDAN POUR TRACTEUR COMPACT AVEC PDF VENTRAL 1-15 RAINURES DRIVELINE FOR COMPACT TRACTOR WITH MID PTO 1-15 SPLINES #700738...
Torque specification table Torque specification table • The following table shows the minimum torque requirement • Maximum is 15% more than the minimum (example: min100 Nm -> max is 115Nm) • If specific thread is not specified in the part list or manual, the bolt thread is coarse •...
NOTE: All warranty work must be performed by an authorized dealer using original (manufacturer) replacement parts. NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify any product previously manufactured.
Need help?
Do you have a question about the BERCO 700725 and is the answer not in the manual?
Questions and answers