Introduction Introduction To the purchaser This new accessory was carefully designed to give years of dependable service. This manual has been provided to assist in the safe operation and servicing of your attachment. All photographs, illustrations and information in the manual may not necessarily depict the actual models or attachments, but are intended for reference only and are based on the latest product information available at the time of publication.
Important safety informations Important safety informations Safety alert symbol/Signal words/Safety messages These are common practices that may or may not be applicable to the product described in this manual. SAFETY ALERT SYMBOL THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
Page 5
Important safety informations • • Exercise extreme caution when operating on or Handle fuel with care, it is highly flammable and crossing gravel drives, walks or roads. Stay alert vapors are explosive. for hidden hazards such as traffic, fences, trees, a) Extinguish all cigarettes, cigars, pipes and other buildings, wires, etc.
Page 6
Important safety informations TRANSPORT Remove all tools and unused parts from equipment before operation. • • Review Transport Safety instructions in the Disconnect battery ground cable (-) before vehicle manual before moving or hauling. servicing or adjusting electrical systems or •...
Important safety informations Security decals Read and understand all instructions/explanations noted on decals or/and in the “Safety Decals” section • Keep the safety decals clean and visible • For decal location see part list section of this manual • Replace decals if decals are missing or illegible •...
Assembly & initial configuration Assembly & initial configuration Tractor requirements General assembly instructions The subframe and brackets kit are designed to be • installed on a TYM T394 tractor only and to be used with Unless otherwise specified, torque all bolts to approved accessories only.
Assembly & initial configuration Accessory assembly Installation of the hitch brackets: Install the right hitch bracket (item 1) and the left hitch WARNING bracket (item 2) under the bumper support plates as THIS ACCESSORY AND ALL OPTIONS ARE HEAVY! shown. To avoid risk of strain injury, NEVER lift the accessory or Bolt in place using six hex bolts M12 X 1.75 X 35 GR10.9 any options by hand alone when handling the components...
Assembly & initial configuration Reinstalling the bumper: Install the bumper (item C) with a shim (item 1) on each side. Bolt in place using two hex bolts M10 X 1.50 X 45 (item 2), two 7/16 "lock washers (item 3), two 7/16" hole flat washers (item 4) and secure with using two nylon insert lock nuts M10 X 1.50 (item 5).
Assembly & initial configuration Installation of the driveline shaft (700843) if applicable: Insert the key (item 2) on the shaft (item A). Insert the driveline shaft (item 1) on the shaft making sure that the key remains in place. Secure everything with a hex bolt. 1/4’’ n.c. X 2 1/2’’ (item 3) and a nylon insert lock nut (item 4).
Hook-up and un-hook accessory Hook-up and unhook accessory Note: The front loader must be removed from the vehicle C. Stop the vehicle, see the vehicle shut-down procedure for stopping the vehicle in the operation Hooking-up the subframe section. D. Connect the hydraulic hoses (item 1) to the vehicle. (Method #1 : subframe alone): Make sure the excess hoses are on the subframe to A.
Page 13
Hook-up and un-hook accessory Finalization of hooking Option B: without accessory Secure the front subframe in place with the pin (item K. Raise the lift arms (item 2) 4) and the lynch pin (item 5). Remove the wooden block. Stop the vehicle, see the procedure for stopping the Unite the driveline shaft to the mid P.T.O.
Hook-up and un-hook accessory (Method #2 : subframe with accessory Make sure the excess hoses are on the subframe to allow the subframe to move. See subsection already installed): "installation of hydraulic hoses" in the section "hook and un-hook accessory". Start the vehicle engine and lower the lift arms (item A.
Hook-up and un-hook accessory Unhook the subframe (Method #2: subframe with accessory already installed): (Method #1: subframe alone): IMPORTANT: When an accessory is installed on the Refer to the “hook-up the subframe method # 1” section vehicle, it is not recommended to use this method if for more details, because the unhooking is done in the there is not enough clearance to slide the subframe same way as the hooking, but in reverse order.
Hook-up and un-hook accessory Hooking-up the snowblower A. Drive the vehicle toward the accessory and unite Unhooking the snowblower them by raising the lift arms (item 1), do not raise the Refer to the hooking section of the snowblower, as the accessory more than 0.25 inches from the ground.
Hook-up and un-hook accessory Installation of hydraulic hoses DANGER To avoid serious injury or death: • Escaping hydraulic oil under pressure can have sufficient force to penetrate skin, causing serious personal injury. If injured by escaping fluid, obtain medical treatment immediately. •...
Operating instructions Operating instructions Safety precaution WARNING DANGER To avoid serious injury or death caused by vehicle overturn: To avoid serious injury or death : Operate only with tractor equipped with an approved • Always follow all safety precaution in the important rollover-protective structure (ROPS) or ROPS cab and safety information section of this manual.
Operating instructions Operating instructions Pre-Start Operation Always inspect the accessory before starting use. See the section "Maintenance and lubrication". Vehicle shut-down procedure Always shut down vehicle before dismounting 1. If engaged, disengage PTO 2. Park on level surface, engage parking brake, lower attachment to the ground, turn off engine, and remove key to prevent unauthorized starting.
Troubleshooting Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Accessory does not lift or lower Dirt in the oil Change hydraulic oil or raises too slowly Damaged bushing Replace the bushing...
Maintenance & Lubrication Maintenance& Lubrication WARNING To avoid serious injury or death : • Always follow all safety precautions in the important safety information section of this manual. • Follow all instructions and safety precautions in your vehicle manual and any other related accessory manual.
Dismount and storage Dismount and storage Long-term storage Transportation Follow unhooking instruction in the section “Hook -up WARNING and Unhook Accessory” of this manual. To avoid serious injury or death : • Clean the accessory When travelling on public roads, use SMV sign, clean •...
Torque specification table Torque specification table TO BE USED WHEN A TIGHTENING TORQUE IS NOT SPECIFIED IN THE TEXT • The following table shows the minimum torque requirement • Maximum is 15% more than the minimum (example: min100 Nm -> max is 115Nm) •...
NOTE: All warranty work must be performed by an authorized dealer using original (manufacturer) replacement parts. NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify any product previously manufactured.
Need help?
Do you have a question about the BERCO 700964 and is the answer not in the manual?
Questions and answers