Advertisement
Quick Links
Advertisement
Related Manuals for Dell P1917S
Summary of Contents for Dell P1917S
- Page 1 19" LCD Monitor Dell P1917S-P1917SWh Service Service Service Simplified...
-
Page 2: Important Safety Notice
Accordingly, a servicer who uses a service procedure or tool which is not recommended by DELL must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. - Page 3 1. Exploded view diagram with list of items...
- Page 4 Description Q’ty LOGO DELL 27 INSULATING SHEET BEZEL KEY_FUNCTION KEY_POWER KEY BOARD PANEL INSULATING SHEET ADAPTER BOARD INSULATING SHEET MAIN BOARD MAINFRAME spring KNOB Part No. Description Q’ty KEY_FRAME 0Q1G6019 1 SCREW(KEY BOARD/BEZEL) MAINFRAME QM1G26400601200AXL SCREW -- --6(MAIN BOARD/MAINFRAME) USB BOARD...
- Page 5 Wiring connectivity diagram...
-
Page 6: Mechanical Instruction
3. Mechanical Instruction Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: − Phillip head Screwdriver − Hex Screwdriver − Penknife ... - Page 7 3.1 Disassembly Procedures: Step Figure Remark Turn off power, S1.Before Unplug external disassemble cablesfrom product Press the button on the red then pull out the S2. Remove the stand upward, stand will stand be remove.
-
Page 8: Rear Cover
Use a Philips-head screwdriver to remove 4 screws for unlocking mechanisms. (No.1~4 screw size=M4x10; Torque=12±2kgf.cm） Use Penknife to S3.Remove the separate the bezel and REAR COVER. rear cove follow the arrows in sequence Tear down black tape then release the USB cable in red, you can take out rear cover. - Page 9 Disconnect the pins. S4.Remove the USB board Use a Philips-head screwdriver to remove 2 screws for unlocking USB board. (No.1~2 screw size=Q3x4; Torque=4±1kgf.cm) Use a Philips-head S5.Remove the screwdriver to remove 3 key board screws for unlocking key board (No.1~3 screw size=M2x2.5;...
- Page 10 1. Tear down tape in S6. Remove blue. Main fram from 2. Disconnect cable in Panel S7. Remove the Tear out connect in red, Mylar of Power remove the Mylar Board...
- Page 11 Use a Philips-head screwdriver to remove 6 screws for unlocking Main board and Power board (No.1~5 screw size=D3x6; Torque=6±1kgf.cm S8. Remove the No.6 screw Main and Power size=M4x6; Board Torque=6±1kgf.cm) Use a hex screwdriver to remove 2 screws for unlocking mainboard （No.1~2 Hex screw Torque= 4.5±0.5kgf.cm) Mainframe...
- Page 12 3.2 Assembly Procedures: Step Figure Remark Use a Philips-head screwdriver to screw 6 screws for tighten Main board and Power board (No.1~5 screw size=D3x6; Torque=6±1kgf.cm S1. Tighten the No.6 screw Main and Power size=M4x6; Torque=6±1kgf.cm) Board Use a hex screwdriver to screw 2 screws for tighten mainboard （No.1~2 Hex screw...
- Page 13 S3. Assembly 1. Connect cable in red Main frame 2. Paste tapes in blue. Use a Philips-head S4.Assembly the screwdriver to screw 3 key board screws for tighten key board (No.1~3 screw size=M2x2.5; Torque=0.9±0.4kgf.cm)
- Page 14 Connect the pins. S5.Assembly the USB board Use a Philips-head screwdriver to screw 2 screws for locking USB board. (No.1~2 screw size=Q3x4; Torque=4±1kgf.cm) Connect the pin and paste the black tape S6.Assembly the REAR COVER. Use a Philips-head screwdriver to screw 4 screws for locking mechanisms.
- Page 15 S7. Assembly the stand...
-
Page 16: Troubleshooting Instructions
4. Trouble shooting instructions...