Related Manuals for Leviton Hi-Fi 95A02-3
Summary of Contents for Leviton Hi-Fi 95A02-3
- Page 1 Hi-Fi 2 4x4 Installation Manual Four Zone - Four Source Digital Audio Distribution System PK-93498-10-B0-5C © 2015 Leviton Mfg. Co., Inc.
- Page 3 WARNINGS AND CAUTIONS • WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never push objects of any kind into this product through openings, as they may touch dangerous voltages. • WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
-
Page 4: Table Of Contents
CONTENTS Precautions ......................1 Important Safety Instructions ..........................1 Introduction ......................3 Hi-Fi 2 4x4 Inputs and Outputs ........................... 3 Installation ......................5 Installing Remote Input Modules (RIM) ......................5 Changing the Color of the RIM ........................... 5 Setting the Frequency of the IR Output ......................6 IR Output ................................ -
Page 5: Precautions
Precautions Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: DURATION PER DAY (HOURS) SOUND LEVEL (dB) - Page 6 -Fi2 Wiring Diagram...
-
Page 7: Introduction
Introduction Hi-Fi Thank you for choosing the 4x4 audio distribution system. Hi-Fi 2 4x4 is an affordable high fidelity Central Controller Distributed Audio System that powers speakers through digital amplification. This installation guide is intended as an aid to installing the Hi-Fi 2 4x4 (Four Zone, Four Source Kit). The installer should also have thoroughly reviewed and understood the Hi-Fi 2 4x4 User’s Guide which has important information regarding operation and configuration of the system. - Page 8 “System On” Output on an auxiliary amplifier that is equipped with a voltage trigger. This jack is where an LEVITON controller or other device with a serial Serial Control interface is connected for configuration and control of the Hi-Fi 2 4x4.
-
Page 9: Installation
The color of the RIM may be changed to complement the interior décor. The RIM is supplied with a white faceplate and insert. Additional colors are available; contact your LEVITON distributor for more information. Change the color of the RIM as follows: 1. -
Page 10: Setting The Frequency Of The Ir Output
Setting the Frequency of the IR Output When using the RIM to send IR data to source equipment, there are two different IR carrier frequencies at which the RIM can transmit the IR signal. The default setting of 38 kHz is used for most audio sources. However, most cable and satellite converter boxes operate at a higher IR carrier frequency closer to 56 kHz. -
Page 11: Installing Volume-Source Control (Vsc) Keypads
The color of the VSC may be changed to complement the interior décor. The VSC is supplied with a white faceplate, rubber keypad, and insert. Additional colors are available; contact your LEVITON distributor for more information. Change the color of the RIM as follows: 1. -
Page 12: Serial Control
TO SERIAL PORT ON 4x4 can be remotely controlled Hi-Fi CONTROLLER through an LEVITON controller or by a device with a serial interface. When connected, the remote device can select an audio zone and change its power state, source, volume... -
Page 13: Ethernet Control
When used with an LEVITON controller and Two-Way Voice Module with Line-Level output and Mute/Page Control, custom announcements can be made over all zone speakers when certain events take place. -
Page 14: Speaker Wiring
The Hi-Fi 2 4x4 system is designed to work with one pair of 8-ohm speakers per audio zone. If additional speakers are required in an audio zone, LEVITON recommends: a) use the Zone Grouping feature of Hi-Fi 2 4x4 where two or more audio zones control the same source, volume, and/or power state so that any or all of these items are controlled together;... -
Page 15: Variable Output
1) Connect the power amplifier to the Hi-Fi 2 4x4 Main Assembly by inserting a 3.5mm stereo connector into the 3.5mm jack labeled “Zone 1” under “Line Out” - (LEVITON 62A14-1, 3.5mm male to 2 RCA male retractable patch cable may be used). -
Page 16: Powering The Hi-Fi 2 4X4 System
Powering the HI-FI 2 4x4 System The supplied Power Supply (Part Number: 95A06-1) powers the entire system including the Hi-Fi 2 4x4 processor, zone amplifiers, Remote Input Modules, and Volume-Source Control keypads. 1) Insert the connector for the Power Supply into the Power jack (under the Standby LED Indicator) on the Hi-Fi 2 4x4 Main Assembly. -
Page 17: Specifications
Specifications Zones 1-8 Power Amplifier Outputs Continuous Average Output Power: 40W (20W x 2), Two channels driven 20-20kHz @1% THD Rated Distortion (1/2 power): 0.20% Rated Impedance: 8 Ohms Damping Factor: Frequency Response (20-20kHz): ±1dB Preamplifier Section Variable output: 0-600mV Impedance: 100 Ohms Source Inputs 1-4... - Page 20 LEVITON LIMITED WARRANTY Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that products manufactured by Leviton under the Leviton brand name (“Product”) will be free from defects in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date.