Failure to do so may result in an accident. INSTALLATION LOCATION KEEP THE VOLUME AT A LEVEL WHERE Make sure PWD-X5 will not be installed in a YOU CAN STILL HEAR OUTSIDE NOISES location subjected to: WHILE DRIVING.
PWD-X5 machine is supplied with the wired controller. Using the wired controller could easily control PWD-X5 machine, or using the mobile phone app or software to adjust or set the audio effect of PWD-X5 machine. These three control methods are varied and thus they will be described individually in the following chapters.
2. Turn On the PWD-X5 unit 3. Turn Bluetooth ON on the smartphone. 4. Search for DSP-HD-XXXXX 5. Select DSP-HD-XXXXX 6. Launch the Alpine PWD-X5 APP on your smartphone Go to Alpine page →Read the Disclaimer carefully and click “Accept” to go to the homepage.
1. Click [Pro users] to change DSP 1. Select the [ ] to begin pairing to the functions PWD-X5. [ ] will show when paired, which represents that app could control the main machine to play music and set data.
Mobile Phone App 2. Use the slider to change the HPF/LPF Reset / Restore Equalizer crossover frequency. 1. Click [Reset EQ] to reset all EQ parameters to the default values 2. Click [Restore EQ] to toggle between EQ on/off Output Level, Phase and Mute 1.
Time Correction 1. Select Output 2. Select Delay 3. Select unit of measure (ms,inch,cm) 4. Use the +/- buttons to change the value. Balance/Fader 1. Press the dot and slide to change the balance and fader.
Before connecting PWD-X5 main machine to PC, please install PWD-X5 software PC Interface Control Interface PWD-X5 PC software has two interfaces for controlling master tuning: EQ and crossover. Click on the EQ curve graph to enter the EQ and crossover interface.
Software for PC PC Interface PC Connection 2. Select [Upgrade] to perform new updates provided by Alpine Electronics. 1. Connect the USB and launch program. 2. Press Connect Mine, Save, Open 1. Select Mine to show language and input mode.
Software for PC Call and Store Preset Time Correction 1. Select Delay 1. Call and store preset sound effect. Click 2. A window will popup where you can adjust [Save] to set 15 preset sound effects. the units, and value per channel. Set Output Channel EQ 1.
Page 12
3. Adjust EQ Gain, Frequency, Q factor by entering the desired values. 4, Adjust HPF/LPF and Slope (ch1-4 6/12db/oct, ch 5 6/12/18/24 db/oct) for the channel. output signals.
Wired Controller Remote Commander Operating Instructions Connect PWD-X5 wired controller to PWD-X5 Switching Sources machine and power on properly. 1. Press the knob to change input source active. Note: The controller will not work if PC/BT is 2. Turn to select and press once to select.
Page 15
➇ The machine is connected to the power external Bluetooth interface to play lossless music via the external digital Bluetooth and supply. connect to PWD-X5 app. After the Bluetooth is connected, the indicator light will be on. Notes: ➂ AUX input interface connects to in-vehicle ●...
Technical Parameter Indicators 1. Technical Specifications Max. output power Rated power: 25W x4 +165W; peak power: 50W x4 +240W ≥80dB Signal-to-noise ratio Bass boost -12dB to +12dB Frequency response 20Hz to 20KHz Input impedance Low-level input: 20kΩ; high-level input: 100Ω Phase 0°/180°...
Page 17
Frequency range: 2.400 to 2.484 MHz Maximum power: 4.51 dBm / 2.82mW (EIRP) The control software for the PWD-X5 can be found in the respective app store for iOS and Android. The apps are free of charge. The full owner’s manual can be found in the support section of your local Alpine website.
Page 18
California 90501, U.S.A. 95 945 Roissy CDG cedex Phone 1-800-ALPINE-1 (1-800-257-4631) FRANCE Phone : + 33(0)1 48 63 89 89 ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 161-165 Princes Highway, Hallam ALPINE ITALIA S.p.A. Viale Cristoforo Colombo, 8 Victoria 3803, Australia...
Need help?
Do you have a question about the PWD-X5 and is the answer not in the manual?
Questions and answers