Page 1
This merchandiser conforms to the American National Standard Institute & NSF International Health and Sanitation standard ANSI/NSF - 7 2003. PRINTED IN Specifications subject to REPLACES ISSUE PART 11/05 4/07 9037179 IN U.S.A. change without notice. EDITION DATE REV. Tyler Refrigeration * Niles, Michigan 49120 Get user manuals: See SafeManuals.com...
........22 End Coil Cover (TLM/TLF) ....... . 22 Refrigeration Line Cover (TLM Only) .
Page 3
Cladding and Trim Parts List ......34 TYLER Warranty ....(See General-UL/NSF I&S Manual)
Page 4
TLM, TLF, TLD SPECIFICATIONS TLD Lift Front Straight Glass Blower Service Merchandisers TLM/TLF Lift Front Straight Glass Gravity Service Merchandisers Page 4 April, 2007 Get user manuals: See SafeManuals.com...
Page 5
Installation & Service Manual TLM, TLF, TLD April, 2007 Page 5 Get user manuals: See SafeManuals.com...
Page 6
TLM, TLF, TLD Page 6 April, 2007 Get user manuals: See SafeManuals.com...
Installation & Service Manual TLM, TLF, TLD Pre-Installation Check List INSTALLATION PROCEDURES WARNING WARNING These cases are very heavy and require The raised front glass projects in front of two or more people to unload, move, the case and could cause personal injury position and/or install them.
TLM, TLF, TLD NOTE Carpentry Procedures Front and rear edges of legs or pedestals Case Line-Up should always be used to line-up cases. Cases with legs have built-in leveling Before starting the case line-up, review the adjustment capabilities. Cases with store layout floorplans and survey the areas pedestals use 6”...
Installation & Service Manual TLM, TLF, TLD Lift Front Glass Leveling Instructions Accurate leveling is critical for the proper operation of the lift glass on this case. In some instances, setting the case on an apparently level floor can cause the lift glass to fit improperly.
TLM, TLF, TLD Rear Rail Cover & Close-off Installation Trim Installation (Cases with Pipe Legs) Position rear rail cover (1) over rear raceway opening and secure with screws in every hole. Bottom and End Close-off Installation Kickplate, optional rear bottom and end close-offs have spring clips on their back sides that secure to the pipe legs.
One thermostat and one solenoid are with screws, if required, using same required for up to three cases. alignment as old bumper track. The TLM, TLF and TLD cases use an electronic thermostat for improved temperature control. Typical Service Case with Gravity Coil 2.
TLM, TLF, TLD THERMOSTAT BULB PLACEMENT 2. Connect sensor wires to the common (COM) and sensor (SEN) terminals of the terminal strip located at the top left of the printed circuit board. The sensor leads are interchangeble. 3. Set the Heating/Cooling jumper blocks to Typical Service Case with Blower Coil the “COOL ”...
120V circuit. The The wiring diagrams on pages 14 thru 21 will case fan circuit is not cycled on this case. cover all TLM, TLF and TLD case circuits. July, 2005 Page 13 Get user manuals:...
Lower Trays and Screens reverse order. 1. Open the front straight glass by lifting Refrigeration Line Cover (TLM Only) the handle at the bottom. 1. Open the front straight glass by lifting the 2. Remove product from the case interior.
Cleaning Instructions WARNING TYLER Refrigeration does not recommend the use of high pressure cleaning equipment on service style cases!! The sealing of front glass and end joints is critical in these cases and high pressure cleaners can penetrate and/or damage these seals. Damaged seals allow water leaks and/or air leaks that can cause poor case refrigeration.
Page 24
TLM, TLF, TLD TYPE OF CLEANING CLEANING AGENT* APPLICATION METHOD** EFFECT ON FINISH Paste NuSteel or DuBois Rub with dry cloth. Use a Use in direction of polish lines Temp small amount of cleaner. on No. 4 (polished) finish. May scratch No. 2 (mill) and No.
Installation & Service Manual TLM, TLF, TLD Grease and oil Organic solvents such as Rub with a cloth. Organic Satisfactory for use on all carbon tetrachloride, tri- solvents may be flammable finishes. chlorethylene, acetone, kero- and/or toxic. Observe all sene, gasoline, benzene, precautions against fire.
One level of shelving is optionally The optional scale shelf is mounted to the available for TLM and TLF cases, while two mullion on the back of the case. The shelf levels of shelving is available for TLD cases.
Installation & Service Manual TLM, TLF, TLD SERVICE INSTRUCTIONS Light Servicing See “General (UL/NSF) I&S Manual” for Connecting the Refrigeration preventive maintenance, T-8 lamp, fan Piping and Components blade and fan motor (TLD) replacement instructions replacement. WARNING Ballast and Lighting Locations...
Front Glass Anti-Fogging System Replacement Service WARNING TLM, TLD and TLF cases have a front glass Shut off or disconnect power supply to anti-fogging fan and a front glass anti-sweat case before replacing the light shield heater. Use the following instructions to anti-sweat.
Installation & Service Manual TLM, TLF, TLD 6. Note position of old heater wire and foil Lift-Glass Replacement tape. Unpug heater wire from harness WARNING connector and remove foil tape and heater wire. Install new heater wire and Wear safety glasses and gloves and use foil tape in same position as removed.
TLM, TLF, TLD NOTE Lift-Glass Gas Piston Replacement Note positioning and installation of top WARNING edge channel before removing. The TL series cases rely upon gas pistons to assist lifting the glass and holding it in the raised position. The glass is heavy and difficult for one person to lift alone while replacing a gas piston.
Installation & Service Manual TLM, TLF, TLD Color Band, Bumper and Bumper Retainer Replacement NOTE Color band, bumper and bumper retainer must be removed to access the upper screws in the front upper cladding. 1. Open the lift glass and remove screws, color band and color band backers from bottom glass support.
TLM, TLF, TLD Anti-Sweat Heater Wire Deflector Kit Replacement (TLD Only) All TLD models have anti-sweat heaters under each lower rear door frame. Use the following instructions to replace an anti-sweat heater wire deflector kit. WARNING Shut off or disconnect power supply to case before replacing any part of the anti-sweat heater wire deflector kit.
5191445 5191445 5191445 5191445 Electronic Thermostat 9043552 9043552 9043552 9043552 Check Valve (TLM) 5199417 5199417 5199417 5199417 For information on operational parts not listed above contact the TYLER Service Parts Department. November, 2005 Page 33 Get user manuals: See SafeManuals.com...