Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jcm-tech BASE500
Summary of Contents for jcm-tech BASE500
- Page 1 USER MANUAL LINK COMMUNICATION MODULE...
-
Page 2: Table Of Contents
Table of contents Important safety instructions Use of the equipment Introduction General description Installation Cabling Base500-1B or Base500-2B Base500-2 Settings/start-up WIFI WIFI: WPS WIFI: manual setting WIFI: reset Activation in Cloud Assistant Updating firmware Verification LED indicators Solving problems Frequent questions... -
Page 3: Important Safety Instructions
Important safety instructions Disconnect the power supply whenever you proceed to the installation or repair of the equipment. In compliance with the European Low Voltage Directive, we inform you of the following requirements: •When the devices remain permanently connected, an easily accessible connecting device must be incorporated into the wiring. •This system must only be installed by qualified professionals that have with automated garage doors and knowledge of the rel- evant European standards. -
Page 4: Introduction
General description LINK is a connectivity module which allows a BASE500 receiver already installed to be updated in real time. It is a plug-in electronic card which, via the WIFI network of a router with internet access, connects to CloudAssistant and provides remote access to the receiver’s memory. -
Page 5: Installation
Installation Cabling Base500-1B or Base500-2B Connect power cables from the existing receiver to the LINK module. jcmtechnologies... - Page 6 Base500-2 jcmtechnologies...
-
Page 7: Settings/Start-Up
Settings/start-up If you have acquired the LINK module as part of an M2M kit, the module comes from the factory prelinked to the Router. DO NOT ALTER THE WIFI PARAMETERS. WIFI To communicate with Cloud Assistant, the LINK module has to be connected to a WIFI Router with internet access by WPS (only compatible routers) or manually. -
Page 8: Wifi: Manual Setting
WIFI: manual setting By default, the LINK device starts up inWIFI SETTINGS mode after power is connected. (indicators: ST blinking green, NW blinking red & IN off) . If WIFI SETTINGS mode does not start after power is switched on, it needs to be reset ("Settings/start-up->WIFI: reset"). From the computer, tablet, smartphone or similar: 1. -
Page 9: Wifi: Reset
4. Put in the password for the WIFI net- work and select SAVE 5. The LINK device exits WIFI SETTINGS mode (see LED indicators) WIFI: reset To reset the LINK device follow these steps: 1. Press the WPS/reset button for more than 10 seconds. -
Page 10: Activation In Cloud Assistant
Activation in Cloud Assistant The first time you want to manage your installation through Cloud Assistant you will need to activate the LINK device through the "Activation Key". This key is found on the label on the back of your equipment. This activation will not be needed for subsequent use. -
Page 11: Updating Firmware
Updating firmware To update the firmware of your LINK device follow these steps: 1. Find the updating jumper (see page 4) and make a bridge on its terminals. 2. The ST, NW and IN LEDS begin to blink in green (10 s, approx.). -
Page 12: Verification
Verification LED indicators Pay special attention to the state of the LED indicators on your LINK board to see at any time what process the equipment is jcmtechnologies... - Page 13 LED STATE LED COLOUR MEANING Inactive GREEN BLINKING In process STEADY GREEN RED BLINKING Awaiting action by installer STEADY RED Error ACTION STATE ST ( NW ( IN ( State Network Internet ----- NO FIRMWARE Contact JCM STARTING Wait WIFI SETTINGS Set WIFI adjustments via WPS or temporary internal web (section "Settings/start-up- >WIFI")
-
Page 14: Solving Problems
Q: I have plugged the LINK module in and, when I switch on, the receiver gives an uninterrupted whistle. What’s wrong? A: Check that you have correctly connected both the MEM500 memory to the LINK module and the LINK to the BASE500 receiver, and that the LINK has power. -
Page 15: Notes
Notes jcmtechnologies... -
Page 16: Technical Data
EU Declaration of conformity The manufacturer JCM Technologies declares that the product LINK complies with the relevant fundamental requirements of the RED Directive 2014/53/EU and of the RoHS Directive 2011/65/EU. See website www.jcm-tech.com/declarations/ JCM TECHNOLOGIES, SA C/COSTA D'EN PARATGE, 6B 08500 VIC (BARCELONA)