Table of Contents
Related Manuals for CARLO GAVAZZI MC36C
Summary of Contents for CARLO GAVAZZI MC36C
- Page 1 MC36C Safety magnetic sensors Instruction manual Manuale d’istruzione Betriebsanleitung Manuel d’instructions Manual de instrucciones Brugervejledning 使用手册 Carlo Gavazzi Industri A/S Over Hadstenvej 40, 8370 Hadsten, Denmark...
-
Page 3: Table Of Contents
9.6 Approvals / tests ..........................12 9.7 Safety classification ........................... 13 9.8 Mechanical data ..........................13 9.9 Cable version ........................... 13 9.10 Plug version ........................... 13 9.11 Pigtail version ..........................13 Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... - Page 4 Service and warranty In the event of malfunction or requests for information please contact the CARLO GAVAZZI branch or distributor in your country. Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S...
-
Page 5: Introduction
2 numbers after the letter “A” in the code. Example: MC36CH2OL with 2 x NO contacts, left exit, without LED and with a cable of 5 meter long: MC36CH2OLA5. Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 6: Product Description
N.O.: contact is open and non-conductive when sensor is not operated with actuator magnet MC36CM away from the sensor. N.C.: contact is closed and conductive when sensor is not operated with actuator magnet MC36CM away from the sensor. Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 7: Mounting And Mechanical Dimensions
XZ-plane can be seen in figure 3. Notice that any misalignment in this plane will reduce the switching distance in the Y-axis. Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 8: Installation
Do not dispose of the packaging in the environment. • Maximum current must be limited by external circuit (e.g. with a resistor in series with the sensor wires) Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 9: Operating And Alignment Direction
The Assured switch-off distance Sar is the one in which, when the actuator moves away from the sensor, all safety contacts have released and return to the rest position. Note: the typical detection characteristic shown in Fig. 3 may vary from sensor to sensor. Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 10: Electrical Connections
1NC + 1NO, cable 2NO, cable 1NC + 1NO, cable with LED 2NO, cable with LED 1NC + 2NO, cable 1NC + 2NO, cable with LED Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 11: Maintenance And Disposal
Dispose of the device in accordance with the national environmental regulations when it is no longer used. Warning: The operating time of the device is restricted to T10D. After that period, the device must be replaced. T10D=B10D/Nop (refer to EN ISO 13849-1) Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 12: Technical Data
IP67; IP69K for M8 versions without LED Pollution degree 9.6 Approvals / tests IEC 60947-5-2 Shock resistance (EN 60068-2-27) 30 g (11 ms) Vibration resistance (EN 60068-2-6) 10 g (10…150 Hz) Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S... -
Page 13: Safety Classification
MC36CM max. 4 MC36CH1O1CxT1L 1NO + 1NC MC36CM max. 4 • L= left exit • R= right exit *assuming a correct alignment between sensor and actuator Rev.2 | MC36C safety magnetic sensors | © 2022 | CARLO GAVAZZI Industri A/S...
Need help?
Do you have a question about the MC36C and is the answer not in the manual?
Questions and answers