Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Malone Post Driver
Summary of Contents for Malone Post Driver
- Page 1 Post Driver Operators Manual ENSURE ALL OPERATORS ARE FAMILIAR WITH THIS OPERATORS MANUAL, BEFORE USING THE MACHINE Issue: 005 Malone Farm Machinery Ballyglass, Claremorris, Co. Mayo, F12 AP11 Republic of Ireland www.malonefm.com...
-
Page 2: Table Of Contents
GENERAL INFORMATION ······························································· 4 TECHNICAL DATA ········································································· 5 DESCRIPTION ··············································································· 5 SAFETY INFORMATION ·································································· 6 SAFETY DECALS ············································································ 7 OPERATING THE MACHINE ···························································· 8 MAINTEANCE AND LUBRICATION ················································· 12 MALONE LIMITED WARRENTY······················································ 13 10. SPARE PARTS SECTION ································································· 15 Version 5—15/03/2021... -
Page 3: Ec Declaration Of Confirmity
Claremorris, Co.Mayo F12 AP11 Republic of Ireland Declare under our sole responsibility that: The product (type): Post Driver ..................... Product code: Post Driver ...................... Serial No: ..........................Date: .............. Manufactured by the above company Conforms to EU Engineering Regulations and other relevant EU guidelines. -
Page 4: General Information
This manual is an important part of your machine. It should remain with the machine if and when it is sold. If it is damaged or lost, you may contact your dealer, or Malone Farm Machinery company to get a replacement. -
Page 5: Technical Data
Max 11' x Ø12'' 3. DESCRIPTION The Malone Post Driver is an attachment for tractors. The weight is raised hydraulically and then released in a free fall. Do not risk injury or death by ignoring good safety practices. All accidents can be avoided. -
Page 6: Safety Information
In addition to the instructions stated here always abide by general safety and accident regulations. Never put hands or fingers between hammer and hat or post. • Never stand directly in front of Post Driver while operating. Stand at 45 degrees in case the post is • pushed forward during operation. -
Page 7: Safety Decals
The adjustment of the post driver to these regulations will be entirely under the Client’s own responsibility. The manufacturer is not liable for any kind of damage that could arise from the non-compliance of those rules. -
Page 8: Operating The Machine
Grease weight slide OPERATING THE MACHINE PRE-OPERATION CHECKLIST It is important for both personal safety and maintaining the good mechanical condition of the Post Driver that this checklist is followed. Grease every 10 hour of operation and pre/post season. •... - Page 9 Fit the lower arms to the linkage pins (CAT 2) of the three-point hitch. Attach the top link of the tractor to the machine with a pin (CAT2 top link). Once the Post Driver has been attached to the three-point linkage of the tractor, raise the lift and remove the stands.
- Page 10 Hook on the chain to the weight and lift off the post. • Lift the Post Driver off ground with tractor link arms and move away from post such that the • hammer can be lowered before moving to the next location. NOTE: The hammer weighs 350 kg and must be kept near the bottom of the beam at all times while the tractor is in motion.
- Page 11 Spool control Spool controls should be used smoothly, the weight can fall quickly with only a small movement of the spool. The operator must be aware of the fast movement of the hydraulic top link as well as the weight. Ensure that the top link is fitted with flow restrictors to reduce the speed of the top link.
-
Page 12: Mainteance And Lubrication
The machine should be stored on a firm level site and cannot tip over, in a safe, clean and dry location where it is protected from the elements. It is advisable that prior to storage of the Post Driver at the end of... -
Page 13: Malone Limited Warrenty
Malone warranty system. These conditions are subject to the following exceptions: Parts of the machine which are not of Malone manufacture, such as tyres, tines, PTO shafts, wire • rope, link pins, slip clutches, hydraulic cylinders, etc. are not covered by this Limited Warranty, but are subject to the warranty of the original manufacturer. - Page 14 This Limited Warranty cannot be assigned or transferred to anyone without the prior written consent • of the company. Malone dealers have no right or authority to assume any obligation or take any decision on the • company's behalf, whether expressly or tacitly.
- Page 15 Blank Page...
- Page 16 Spare Parts Post Driver...
-
Page 17: Spare Parts Section
SPARE PARTS SECTION To be assured of the latest design improvements purchase your Genuine Replacements from the Original Equipment Manufacturer through your local Dealer. Always quote: Machine Type • Year of manufacture • Serial Number • Part Code • Part Position Number & Page Number •... - Page 19 VALVE SAFETY GUARD MAP10281 VALVE BRACKET EXTENSION MAP30100 WIRE ROPE PIN MAP10280 VALVE BRACKET MAP10273 RUBBER MAT MAP10286 POST DRIVER HAT MAP10236 LOWER LINK PIN MAP10270 STAND BRACKET MAP10237 TOP LINK PIN MAP25140 RAM PIN MAP10235 PULLEY WHEEL PIN AND NUT...
- Page 21 TOP BLEEDER HOSE - 10in x 1/4in PART NO. DESCRIPTION MAP10272 RUBBER MAT (5 SIDED) MAP10274 RUBBER MAT (SQUARE) MAP10284 POST DRIVER HAT (5 SIDED) MAP10285 POST DRIVER HAT (SQUARE) MAP10291 SAFETY GUARD (GREEN) MAP10290 SAFETY GUARD (MESH) MAP10202 WIRE ROPE (SINGLE EYE)
- Page 22 Blank Page...
- Page 23 Blank Page...
- Page 24 Malone Farm Machinery Ballyglass, Claremorris Co. Mayo, Ireland. Tel +353 (0) 94 936 0500 www.malonefm.com...
Need help?
Do you have a question about the Post Driver and is the answer not in the manual?
Questions and answers