Horizon Fitness 7 Series User Manual page 31

Sets the sound to obtain fixed output level between programmes.
If the Mode menu item is set to an option other than Off the AVL setting options will
change. Auto, Night, Normal and Off options will be available. In Auto mode the
TV will switch to Normal or Night mode automatically according to the current time
AVL (Automatic
information. If no time information is available this option will always function as Normal.
Volume Limiting)
When the TV switches to Night mode for the first time after setting this option as Auto,
an information bar will pop up on the screen.
Please note that compared to Normal mode Night mode provides more aggressive
dynamic compression control which is suitable for silent environments.
Advanced Settings
Equalizer Selects the equalizer mode. Custom settings can be made only when in User mode.
Dynamic Bass
Enables or disables the Dynamic Bass.
Sound Mode
You can select a sound mode (if the viewed channel supports).
Sets digital out audio type. PCM, Auto, and Passthrough options will be available.
PCM: This option provides two-channel uncompressed digital audio output. You can
use this option if you experience compatibility problems such as not hearing sound.
Auto: This option provides multi-channel digital audio output (up to 5.1 channel).
Digital Out
Passthrough: This option provides original audio output as such in HDMI ARC. It is
recommended to use this option if you have an A/V receiver with eARC support. If your
A/V receiver does not support source audio format you may experience compatibility
problems such as not hearing sound.
Sets headphone volume. This option will not be available if the Sound Output option
is set as Lineout.
Headphone
Please ensure before using headphones that the headphone volume is set to a low
level, to prevent damage to your hearing.
Sets sound balance. This feature will be activated if Sound Output option is set as TV
Balance or Headphone Only. Balance item adjusts the balance level of the TV speakers and
headphones together.
Reset Resets some of the sound settings to factory defaults.
Network Menu Content
Network Type Disable the network connection or change the connection type.
Scan Wireless
Start a search for wireless networks. This option will be available if the Network Type
Networks is set as Wireless Device.
To disconnect from a wireless network and delete your saved wireless network profile (if
previously saved), highlight this option and press OK. This option will not be available
Disconnect
if you did not connect to a wireless network. Refer to Connectivity section for more
information.
If your modem/router device has WPS, you can directly connect to it using this option.
Press WPS on your Highlight this option and press OK. Go to your modem/router device and press the
wifi router WPS button on it to make the connection. This option will be available if the Network
Type is set as Wireless Device.
Start a speed test to check your connection bandwidth. The result will be displayed on
Internet Speed Test
the screen when finished.
Advanced Settings
Change the IP and DNS configurations of your TV.
Networked Standby
Enable or disable this feature by setting it as On or Off.
Mode
Note: For detailed information on the options of this menu refer to the Connectivity section.
English - 19 -
Installation Menu Content
Displays automatic tuning options. D. Aerial: Searches and stores aerial DVB stations.
Automatic channel
D. Cable: Searches and stores cable DVB stations. Analogue: Searches and stores
scan (Retune)
analogue stations.
Manual channel
This feature can be used for direct broadcast entry.
scan
Network channel
Searches for the linked channels in the broadcast system. D. Aerial: Searches for aerial
scan network channels. D. Cable: Searches for cable network channels.
You can use this setting for fine tuning analogue channels. This feature is not available
Analogue fine tune if no analogue channels are stored and if currently watched channel is not an analogue
channel.
Displays installation settings menu. Standby Mode Search (*): Your TV will search for
new or missing channels while in standby. Any new found broadcasts will be shown.
Installation Settings Dynamic Channel Update(*): If this option is set as Enabled, the changes on the
broadcasts such as frequency, channel name, subtitle language etc., will be applied
(optional)
automatically while watching.
(*) Availability depends on model.
Use this setting to clear channels stored. This setting is visible only when the Country
Clear Service List
option is set to Denmark, Sweden, Norway or Finland.
Select Active This setting allows you to select only the broadcasts within the selected network to be
listed in the channel list. This feature is available only for the country option of Norway.
Network
You can use this menu item to monitor signal related information such as signal level/
Signal Information
quality, network name, etc. for available frequencies.
First time installation Deletes all stored channels and settings, resets TV to factory settings.
English - 20 -