Page 1
THE USER MUST READ THIS MANUAL BEFORE OPERATING THE PRODUCT. OPERATIONS OTHER THAN THOSE DESCRIBED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND DAMAGE TO THE PRODUCT. Note that any attempt to open or fix the equipment without prior approval by Optilab, LLC voids the warranty. R1.00...
Page 2
All pictures and diagrams are for illustration purposes only and the actual appearance may differ. This document is copyrighted property of Optilab, LLC. It may not be used in whole or in part for manufacture, sale, or design of items without the written permission of Optilab, LLC.
EYDFA-33-PM-R Operation Manual R1.00 Page 1 of 15 1. General Information 1.1 Safety Precautions This product emits high power invisible laser radiation from the optical connector(s) that classifies it to be a CLASS 4 laser product accordingly to IEC 60825-1:2007. The optical output is hazardous to eyes and skin.
Page 5
EYDFA-33-PM-R Operation Manual R1.00 Page 2 of 15 In case when catastrophic failure (plasma formation) has occurred, DO NOT enable the lasers again. Otherwise the optical fiber will continue to burn towards the source of laser radiation at about 1m/s.
If the shipping container or the packing material is damaged, keep it until the contents of the shipment have been checked to be free of mechanical and electrical damages. Notify Optilab, LLC promptly if any notable damage is found.
• Collimated Output (Optional) • Interlock safety feature 2.3 Function Diagram In the following figure, a basic function diagram of the EYDFA-33-PM-R is given. This is a single stage amplifiers. It comes with input and output power monitoring, as well as isolations.
EYDFA-33-PM-R Operation Manual R1.00 Page 6 of 15 3. Product Description 3.1 Panel Diagrams and Controls Front Panel Feature Function The Touch LCD display shows the parameters and optical Main Touch Display settings of the EYDFA rackmount unit. This is a touchscreen type display, see section 3.2.3 for more information.
Page 10
EYDFA-33-PM-R Operation Manual R1.00 Page 7 of 15 Rear Panel Feature Function AC Power Socket The AC power socket is the input for the AC power source. A three-pin standard power cord should be used to connect this equipment to any 110 or 220 V main supply.
EYDFA-33-PM-R Operation Manual R1.00 Page 8 of 15 3.2 Operation Instructions 3.2.1 Preparation Procedure 1. Prior to the operation, read the user manual carefully and refer to laser safety information in Sec 1.2. Inappropriate operation may cause severe damage to the instrument and harm the health of the operators and people close by the amplifier instrument.
EYDFA-33-PM-R Operation Manual R1.00 Page 9 of 15 3.2.3 Change Front Panel Setting To toggle between operation modes or to adjust digits of the pump currents, us the shift key to highlight a parameter to change (it will turn yellow). When the parameter is highlighted, use the “INC”...
EYDFA-33-PM-R Operation Manual R1.00 Page 10 of 15 3.2.4 Turn-Off Procedure 1. It is recommended to turn off the booster stage pump current first before turning off the key switch. 2. Turn off the main AC power switch after the key switch is set to off position.
Page 14
EYDFA-33-PM-R Operation Manual R1.00 Page 11 of 15 Use the following RS232 settings: Baud Rate = 9600 Data Bits: 8 Stop Bits:1 Polarity: None Append carrier return (CR) and line feed (LF) to each command. The following commands can then be executed, with a corresponding confirmation...
EYDFA-33-PM-R Operation Manual R1.00 Page 12 of 15 4. Maintenance and Care 4.1 Troubleshooting Symptom Possible Cause (C) and Solution (S) No Optical Output C: Interlock is open S: Close the interlock using the provided BNC connector or connect it to the compatible interlock system.
EYDFA-33-PM-R Operation Manual R1.00 Page 13 of 15 4.2 Care of Fiber-optic Connectors Damage to optical connectors account for more than 70 percent of equipment performance degradation. To avoid such damage, the user should use only industrial grade 99% pure isopropyl alcohol and follow the procedures below to keep the connectors, adaptors and receptacles clean.
For any questions regarding the operation and performance of the product, please contact Optilab, LLC. Optilab, LLC 600 E. Camelback Road, Phoenix, AZ 85012...
(1) year for all products from date of shipment. During the warranty, Optilab, LLC will either repair or replace, at its option, any defective product (hereafter refer to as Product) within thirty (30) days after its receipt, and Optilab, LLC shall return such repaired or replaced Product to the location from which it originated.