Advertisement
If the Connection is not Established
Automatically
If you cannot connect the speakers to a compatible
model automatically or you use multiple compatible
models and want to specify the compatible model
for connecting the speakers, perform the manual
connection.
The following operation is described for speakers
used with the compatible model HT-A7000. Use the
remote control supplied with the compatible model
HT-A7000 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
1
Press HOME.
The home menu appears on the TV screen.
2
Select
[Setup] - [Advanced Settings] on the
home menu.
3
Select [Speaker Settings] - [Wireless Speaker
Settings] - [Start manual linking].
The [Start manual linking] screen appears on the
TV screen.
4
Press LINK on the speaker.
The power indicator of the speaker that had LINK
pressed flashes twice repeatedly in green.
5
Select [Start].
The manual link starts.
The connecting process appears on the TV screen.
To cancel the manual link, select [Cancel].
6
When [Rear Speaker (R)] and [Rear Speaker (L)]
display [Connected], select [Finish].
7
Press
.
The link is established and the power indicator of
the speakers lights in green.
Note
• If you perform [Start manual linking], [Link mode]
of [Wireless Speaker Settings] is set to [Manual]
automatically.
• Only the speakers for which [Connected] has been
displayed in Step 6 connect to a compatible model.
If the connection of the speakers cannot be
established, perform the manual connection again.
If Wireless Transmission is Unstable
If you use multiple wireless systems, such as a
wireless LAN, the wireless signals may become
unstable. In this case, the transmission may be
improved by changing the following setting.
The following operation is described for speakers
used with the compatible model HT-A7000. Use the
remote control supplied with the compatible model
HT-A7000 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
1
Press HOME.
The home menu appears on the TV screen.
2
Select
[Setup] - [Advanced Settings] on the
home menu.
3
Select [Speaker Settings] - [Wireless
Speaker Settings] - [RF Channel].
4
Select the setting you want.
• [On] (default setting): Normally select this. The
system automatically selects the better channel
for transmission. Stronger mode for wireless
interference.
• [Off]: The system selects a channel from the
limited frequency band to prevent external
wireless interference. If sound dropping occurs
while [On] is selected, it may be improved by
selecting [Off].
Note
• If you change the [RF Channel] setting from [Off] to
[On], it may take 1 minute to reconnect.
• A compatible model may not meet this setting
depending on countries/regions where you
purchase it.
Troubleshooting
If you experience any of the following difficulties
while using the rear speakers, use this
troubleshooting guide to help remedy the problem
before requesting repairs. Should any problem
persist, consult your nearest Sony dealer.
Be sure to bring all of your rear speakers, a
compatible model and optional subwoofer (not
supplied) even if it seems as though only one has a
problem, when you request to repair.
The following solutions are described for speakers
used with the compatible model HT-A7000.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
No sound is heard from the rear speakers.
Make sure the AC power cord (mains lead) of the
rear speaker is connected properly.
If the power indicator on the rear speaker does not
light, try the following.
– Make sure the AC power cord (mains lead) of the
rear speaker is connected properly.
– Press
(power) of the rear speaker to turn on
the power.
If the power indicator on the rear speaker flashes
slowly in green or lights in red, try the following.
– Move the rear speaker to a location near a
compatible model so that the power indicator on
the rear speaker lights in green.
– Follow the steps in "If the Connection is not
Established Automatically."
– Check the wireless connection status. For details,
refer to the Operating Instructions supplied with
a compatible model.
If the power indicator on the rear speaker flashes
in red, press
(power) of the rear speaker to turn
off the power and check whether the ventilation
holes of the rear speaker is blocked or not.
Press REAR
+ on the remote control of a
compatible model to increase the volume of the
rear speakers.
If you change the [RF Channel] setting of a
compatible model from [Off] to [On], it may take 1
minute for the sound to be output.
If the power indicator flashes in red, disconnect
the AC power cord (mains lead) of the rear speaker
from the AC outlet (mains) and reconnect it again.
Sound skips or has noise.
If there is a device nearby that generates
electromagnetic waves, such as a wireless LAN or
a microwave oven in use, locate the rear speakers
and a compatible model apart from that device.
If there is an obstacle between a compatible
model and the rear speakers, move or remove the
obstacle.
Locate a compatible model and the rear speakers
as close as possible.
Switch the network connection of the TV or Blu-ray
Disc player from wireless to wired.
Specifications
Amplifier section
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(FTC)
With 6 ohms loads, both channels driven, from 200 -
20,000 Hz; rated 20 W per channel minimum RMS power,
with no more than 1% total harmonic distortion from 250
mW to rated output.
POWER OUTPUT (reference)
50 W (per channel at 6 ohms, 1 kHz)
Canadian models:
POWER OUTPUT (reference)
50 W (per channel at 6 ohms, 1 kHz)
Speaker system
2-way 2 speaker system
Bass reflex
Speaker
Woofer: 46 mm × 54 mm (1 13/16 in × 2 1/4 in) cone type
Tweeter: 16 mm (21/32 in) dome type
Power requirements
120 V AC, 60 Hz
Power consumption
On: 11 W
Standby mode: 1 W or less
Turned off: 0.5 W or less
Dimensions (w/h/d) (approx.)
100 mm × 187 mm × 100 mm (4 in × 7 3/8 in × 4 in)
(projecting parts not included)
Mass (approx.)
1.1 kg (2 lb 7 oz)
Wireless transmitter/receiver section
Communication system
Wireless Sound Specification Version 4.0
Frequency band
5 GHz
Modulation method
OFDM
Included items
• Rear speaker R (1), Rear speaker L (1)
• AC power cords (mains leads) (2)
• Operating Instructions (1)
Important information
on software
This product contains software that is subject to the
GNU General Public License ("GPL") or GNU Lesser
General Public License ("LGPL"). These establish that
customers have the right to acquire, modify, and
redistribute the source code of said software in
accordance with the terms of the GPL or the LGPL.
For the method to confirm the GPL, LGPL and other
software licenses contained in the rear speakers,
please refer to the Operating Instructions of a
compatible model.
When you use the compatible model HT-A7000,
please refer to [Software License Information] under
[Setup] - [Advanced Settings] - [System Settings]
on the home menu.
You may find a copy of the relevant source code as
required under the GPLv2 (and other licenses) at
https://oss.sony.net/Products/Linux
You may obtain the source code as required by the
GPLv2 on a physical medium from us for a period of
three years after our last shipment of this product by
applying through the form at
https://oss.sony.net/Products/Linux
This offer is valid to anyone in receipt of this
information.
Please note that Sony cannot answer or respond to
any inquiries regarding the content of this source
code.
All other trademarks are trademarks of their
respective owners.
WARNING
To reduce the risk of fire or electric shock, do not
expose these speakers to rain or moisture.
The speakers are not disconnected from the mains as
long as it is connected to the AC outlet, even if the
speakers themselves have been turned off.
To reduce the risk of fire, do not cover the ventilation
opening of the speakers with newspapers,
tablecloths, curtains, etc.
Do not expose the speakers to naked flame sources
(for example, lighted candles).
To reduce the risk of fire or electric shock, do not
expose these speakers to dripping or splashing, and
do not place objects filled with liquids, such as vases,
on the speakers.
As the main plug is used to disconnect the speakers
from the mains, connect the speakers to an easily
accessible AC outlet. Should you notice an
abnormality in the speakers, disconnect the main
plug from the AC outlet immediately.
Do not install the speakers in a confined space, such
as a bookcase or built-in cabinet.
Do not place this product close to medical
devices.
This product (including accessories) has magnet(s)
which may interfere with pacemakers, programmable
shunt valves for hydrocephalus treatment, or other
medical devices. Do not place this product close to
persons who use such medical devices. Consult your
doctor before using this product if you use any such
medical device.
Indoor use only.
For the speakers
The nameplates are located on the bottom of the
speakers.
For the customers in the U.S.A.
NOTE:
These speakers have been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
These speakers generate, use and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If these speakers
do cause harmful interference to radio or television
reception, which can be determined by turning the
speakers off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the speakers and
receiver.
– Connect the speakers into outlets on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Advertisement
