Download Print this page

Advertisement

Quick Links

Operating Instructions
MaxLite LED ModMAX Fixtures
®
General Safety Information
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation
or maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
WARNING:
RISK OF ELECTRICALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label
information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
RISK OF FIRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Input Rating: 120V-277V 50/60Hz
Operating Temperature: -22°F to 122°F
Wet Location Rated
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com
ModMAX Series
Illustrations on the manual are for
installation purposes only. It may not
be identical to the fixture purchased.
Page: 1
REV: 1/11/17

Advertisement

loading
Need help?

Need help?

Do you have a question about the ModMAX 97374 and is the answer not in the manual?

Questions and answers

Summary of Contents for MaxLite ModMAX 97374

  • Page 1 • MIN 90°C SUPPLY CONDUCTORS. Input Rating: 120V-277V 50/60Hz Operating Temperature: -22°F to 122°F Wet Location Rated © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 1 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 2: General Wiring Diagram

    Green = Ground Line connection to be made to switch lead from source. 210W: 420W: © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 2 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 3 M10X20 wrench bolts and M10 internal tooth washers. *Fig. 4 & 5 show 630w model. © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 3 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 4 Flood Mounting Instructions Drill holes for mounting using template below: © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 4 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 5 (Fig. 11).The 420 W version is shown in Fig. 11. Other wattages have differently shaped side brackets, but follow the same steps. Ensure all wrench bolts are tightened. © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 5 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 6 Use appropriate bolt size to mount either method. Secure and torque per selected bolt specifications (Fig. 13 & 14). Follow connecting power procedures after mounting. Restore power. © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 6 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 7 (Fig. 16). Make wiring connections inside the pole following Fig. 1/2/3. © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 7 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 8 Place the fixture/pole mount bracket assembly onto the pole and fix it in place using the six M8 set screws on the sides of the pole mount bracket. (Fig. 17) Restore Power. © Copyright 2017. MaxLite, Inc. All Rights Reserved. Page: 8 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/11/17...
  • Page 9 MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.