Advertisement
Quick Links
Operating Instructions
MaxLite StaxMAX LED Flood Lights
®
General Safety Information
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
WARNING:
RISK OF ELECTRICALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label
information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
RISK OF FIRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Input Rating: 120V-277V 50/60Hz (347/480v optional)
Wet Location Rated: IP65
Operating Temperature: -22°F to 122°F
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com
Picture is for illustration
purposes only. Your
model may vary.
ELLF Series
Page: 1
REV: 1/10/18
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MaxLite ELLF Series
Summary of Contents for MaxLite ELLF Series
- Page 1 Input Rating: 120V-277V 50/60Hz (347/480v optional) Wet Location Rated: IP65 Operating Temperature: -22°F to 122°F © Copyright 2018. MaxLite, Inc. All Rights Reserved. Page: 1 12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com REV: 1/10/18...
- Page 2 4. Connect the purple fixture wire to the (V+) DIM wire. 5. Connect the gray fixture wire to the (V-) DIM wire. Driver Replacements: Contact your local MaxLite® representative or MaxLite® to receive replacements for drivers. Step 6: Unscrew two (2) screws to remove driver cover.
- Page 3 4. Connect the purple fixture wire to the (V+) DIM wire. 5. Connect the gray fixture wire to the (V-) DIM wire. Driver Replacements: Contact your local MaxLite® representative or MaxLite® to receive replacements for drivers. Step 1: Disconnect the power by turning off the Step 6: Unscrew two (2) screws to remove driver cover.
- Page 4 4. Connect the purple fixture wire to the (V+) DIM wire. 5. Connect the gray fixture wire to the (V-) DIM wire. Driver Replacements: Contact your local MaxLite® representative or MaxLite® to receive replacements for drivers. Step 1: Disconnect the power by turning off the Step 6: Unscrew two (2) screws to remove driver cover.
- Page 5 MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.
Need help?
Do you have a question about the ELLF Series and is the answer not in the manual?
Questions and answers