Power Connection; Fuse; Power Switch; Phantom Switch - Mackie 1402 VLZ Owner's Manual

POWER CONNECTION

Just in case you lose the cord provided with
the MS1402-VLZ, its power jack accepts a stan-
dard 3-prong IEC cord like those found on
most professional recorders, musical instru-
ments, and computers.
At the other end of our cord is — get this
— a plug! Not a black cube or, as we're fond of
calling them, a "wall wart." We did this for
some very good reasons:
The MS1402-VLZ has sophisticated power
requirements that a wall wart cannot provide.
Wall warts are inconvenient, fragile, radiate
huge hum fields, hog extra jacks on your
power strip and get in the way. If you lose a
wall wart, you're in trouble, but if you lose the
MS1402-VLZ's power cord, you can get a new
one at any electronics, music, or computer
store. You can even buy them at Radio Shack
(part # 287-1257). Can you tell that we hate
wall warts?
Plug the MS1402-VLZ into any standard
grounded AC outlet or into a power strip of
proper voltage.
WARNING: Disconnect-
ing the plug's ground
pin can be dangerous.
Please don't do it.

FUSE

The MS1402-VLZ is fused for your (and its
own) protection. If you suspect a blown fuse,
disconnect the cord, pull the fuse drawer out
(located just below the cord receptacle) and
replace the fuse with a 500mA (0.5 amps) SLO
BLO, 5x20mm, available at electronics stores
or your dealer (or a 250mA SLO BLO 5x20mm
if your MS1402-VLZ is a 220V–240V unit).
If two fuses blow in a row, something is
very wrong. Please call our toll-free number
(or the distributor in your country) and find
out what to do.
POWER PHANTOM
MICRO SERIES
1402-VLZ
LOW NOISE HIGH HEADROOM
14-CHANNEL MIC/LINE MIXER
MAIN
RIGHT
BALANCED
120 VAC 50/60 Hz 25W
315mA/250V SLO-BLO
CAUTION:
TO REDUCE THE RISK OF
FIRE REPLACE WITH SAME
TYPE FUSE AND RATING

POWER SWITCH

If this one isn't self-explanatory, we give up.
You can leave this switch on all the time; the
MS1402-VLZ is conservatively designed, so heat
buildup isn't a problem even in 24-hour-a-day
operation. There's nothing that will burn out or
get used up. Or, just plug everything into a good
quality power strip for one-button turn-on.
(Perfectly normal. Is that redundant?)
In the output section there is a PWR LED.
If the power is on, so is the LED.

PHANTOM SWITCH

® The Phantom Power Switch controls the
phantom power supply for condenser micro-
phones plugged into channels 1-6 mic inputs
as discussed at the start of this section .
When turned on (or off), the phantom power
circuitry takes a few moments for voltage to
ramp up (or down). This is also perfectly nor-
mal. For an even closer look, refer to
Appendix C.
In the output section, next to the PWR
LED, is the PHAN LED. If the phantom power
is on, so is the LED.
TM TM
CAUTION
RISK OF ELECTRIC SHOCK
REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
MAIN CONTROL
LEFT ROOM
BALANCED BAL/UNBAL
R L R
+4
MIC
MAIN
OUTPUT
LEVEL
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC.
You may notice that
the MS1402-VLZ feels
quite warm in the upper-
right corner. This is
perfectly normal.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
DO NOT OPEN
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
ALT 3-4
OUTPUT
CHANNEL INSERTS
BAL/UNBAL (
PRE-FADER / PRE EQ TIP SEND / RING RETURN
L 6 5 4
WOODINVILLE WASHINGTON
SERIAL NUMBER MANUFACTURING DATE
)
3 2 1
MADE IN USA PATENT PENDING
17