PROFIX Tryton TDW1050K Operating Instruction page 5

operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
The set includes:
n
Impact drill - 1 piece
ź
Auxiliary handle - 1 piece
ź
Depth stop - 1 piece
ź
Carrying case - 1 piece
ź
User's manual - 1 piece
ź
Warranty card - 1 piece
ź
Device components (see Fig. A
n
The numbering of device components refers to graphics presented on page
2 of the user's manual:
1. Keyless drill chuck
2. Operation mode switch drill / impact drill
3. Rotation direction switch
4. Switch lock
5. Rotational speed control
6. Switch
7. Main handle
8. Auxiliary handle
9. Depth stop
SPECIFICATIONS:
MODEL
Voltage
Frequency
Power consumption
No load speed
Drill chuck (keyless)
Maximum hole diameter
Weight (with no accessories)
Equipment Class
Ingress protection
Sound pressure level (LpA)
Sound power level (LwA)
Vibration level according to valid standard EN 60745-2-1:2010
No impact drilling (metal),
main handle a
hD
Impact drilling (concrete) a
hID
tolerance of measurements K=1,5 m/s
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values
given. The above-mentioned causes may lead to higher exposure to
vibrations during the whole work time.
One must implement additional safety measures to protect the
operators from exposure to vibrations, such as maintenance of the
,B,C ):
TDW1050K
220-230 V
50 Hz
1050 W
0-2800 rpm
13 mm
steel - 10 mm
concrete - 13 mm
wood - 25 mm
3,0 kg
II
IP20
92,3 dB(A)
103,3 dB(A)
2
3,914 m/s
2
14,953 m/s
2
electric tool and work tools, assurance of proper hand temperature, or
determination of the sequence of work operations.
BEFORE YOU START:
1. Make sure that power supply parameters meet the requirements
provided on the drill nameplate.
2. Make sure the drill switch is in off position and switch lock (4) is
released. Do not put the device aside when the lock is on. To release
the lock press the switch (6) again.
3. The auxiliary handle (8) can be installed by inserting the handle
clamping ring onto the chuck and locking it by tightening the handle.
The depth stop (9) can be installed by inserting it into the hole of the
auxiliary handle and tightening the auxiliary handle to lock it.
4. When using an extension cord make sure its parameters and cable
cross-section meet the drill power requirements. Extension cords
should be as short as possible. When in use extension cords must be
fully uncoiled.
OPERATION:
Selecting a drill bit
n
When drilling in concrete, bricks, stone masonry bits must be used. When
drilling holes in metal, plastics, wood (hole diameters up to 6mm) use
metal bits.
When drilling holes with a diameter exceeding 6 mm in wood, use wood
drill bits.
Fixing a drill bit
n
Insert a drill bit into the loosened chuck (1) and fix it by tightening the
outer ring holding the chuck body (see Fig.: B).
Setting the drilling depth
n
The depth stop (9) can be used to set drilling depth.
Extend the drill stop to set the distance between depth stop tip and drill
bit tip that equals to the drilling depth required.
Selecting an operation mode
n
Drilling and tightening/undoing screws:
ź
Set the operation mode switch (2) to position «drill» marked with
symbol - .
Impact drilling:
ź
Set the operation mode switch (2) to position «impact drill» marked with
symbol - .
NOTE: Never change the operation mode when the drill chuck (1) rotates.
Changing the rotation direction
n
Move the rotation direction lever (3) to a selected position until you feel
resistance. Symbols on the housing near the switch: R - clockwise
rotation, L- counterclockwise rotation.
NOTE: Never change the rotation direction when the drill chuck (1) rotates.
Turning on/off
n
To turn the power tool on press its switch (6) button and keep it pressed.
To lock the switch in on position press the lock (4).
To turn the power tool off just release the switch (6) button or, when it is
locked with switch lock (4), press it for a moment and then release it.
Controlling the speed
n
By increasing or decreasing the pressure on switch (6) the user can
control the rotational speed steplessly.
5