Summary of Contents for Gaia Baby CO-SLEEPING CRIB
Page 1
Co-Sleeping crib IMPORTANT: Please read carefully and retain for Assembly instructions future reference CHINA Co-sleeper V3.indd 1 18/08/2022 10:44...
Page 2
• WARNING: When the product is used in “Co-Sleeping Crib” mode (Fixed equipped with cords. to the parent’s bed)”, before laying the child in it, make sure that the • A prolonged exposure to the sun may cause changes of tones to the...
Page 3
parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ to form a loop. Repeat this operation on the other side. For easier dummies, etc.), which would pose a risk of strangulation. installation, during fixing of the buckles, we suggest that the crib is kept at a short distance from the parent’s bed.
Page 4
To complete assembly you will need to have the below tools, components and fittings ready Tools Co-sleeper crib Fittings Co-sleeping crib Components A x 8 1 x 2 6 x 2 Allen key B x 4 Supplied 2 x 2...
Page 5
Position 1 Crib base position 10 cm 4 inches IMPORTANT: Before fitting the crib supports (Part 6) to the legs, ensure the tops of the crib support rails are a minimum of 10cm (4 inches) below the upper surface of the beds mattress. 322mm Position 3 Position 2...
Using barrel nuts Stand assembly 1 Barrel nut The barrel nuts come in two parts the barrel and the grub screw. Insert the grub screw into the end of the barrel and Grub turn clockwise. screw Before inserting the barrel nuts into the holes in the component, ensure the end of the barrel nut stud will fit into...
Page 7
Stand assembly 4 Stand assembly 5 Stand assembly 6 Stand assembled CHINA Co-sleeper V3.indd 7 18/08/2022 10:44...
Page 8
Locking castors crib assembly 1 To lock the castors: Push the locking tabs on the castors downwards until the castors lock with a CLICK. To unlock the castors: To unlock the castors, push the locking tabs upwards until it unlocks the castors with a CLICK.
Page 9
Fitting the crib base crib assembly 2 Pull the locking pins on the base rails under the base of the crib outwards until they lock in place with a CLICK (A). Lower the crib onto the stand (B). IMPORTANT: Ensure the base rails on the crib are crib assembly 3 positioned over the rails...
Page 10
crib assembly 1 crib assembly 2 Peel the protective cover off the glue pad on the clip (G). Stick the clips to the end panels (6) just below the slots in the sides of the panels. crib assembly 3 Slot the fabric straps on the clips through the slots of the end panels.
Page 11
crib assembly 4 crib assembly 5 crib assembled Fitting the liner 1 Insert the two metal rods (8) into the sleeves in the tops of the fabric liners (7) sides. CHINA Co-sleeper V3.indd 11 18/08/2022 10:44...
Page 12
Fitting the liner 2 Fitting the liner 3 Slot the ends of the IMPORTANT: Place the liner metal rods into the in the crib ensuring the open gaps between crib end of the liner is at the sides and the crib ends. same end as the two blocks attached to the base as Pull the fabric straps...
Page 13
Fitting the liner 5 Fitting the liner 6 Separate the two velcro tabs on the ends of the fabric insert. Slot the two tabs on the fabric insert through the holes on the top of the end panels. Fitting the liner 6 Fitting the liner 7 Slot the sides of the drop side panels into...
Page 14
Inserting the upper base Adjusting the upper base IMPORTANT: Ensure the fold out foot on the underside of the upper base Flat position is at the same end of the crib as the exposed blocks in the crib. This position is used when the baby is going to sleep in the crib.
Page 15
Fitting the mattress Using the drop sides IMPORTANT: NEVER place a baby in the crib without the mattress Raising the drop- placed inside it. sides: Grip the top of the drop-side and lift upwards as far as it will go. The clips on the inside of the crib ends will support the rod in the...
Page 16
Using the attachment straps 1. (For easier installation, during fixing of the buckles, we suggest that the crib is kept at a short distance from the parent’s bed). Wrap the strap (G) around the front legs of the cribs frame as shown in diagram A.
Page 17
Removing the crib from the stand Fitting the crib to the stand Pull the locking pins Pull the locking pins on the base rails under on the base rails under the base of the crib the base of the crib outwards until they lock outwards until they lock in place with a CLICK.
Page 18
Notes Notes CHINA Co-sleeper V3.indd 18 18/08/2022 10:44...
Manufacturer Warranty All Gaia Baby furniture carries a full 2 year manufacturer’s warranty. The warranty does not cover wear & tear or damage caused by the product not being used in accordance with correct care instructions. The warranty period is effective from date of purchase. The warranty applies to product presented with an original receipt or proof of purchase.
Page 20
Gaia Baby Limited Web: #2, Kinsealy Business Park, Malahide www.gaia-baby.com Email: Dublin K36 DK81 Ireland customercare@gaia-baby.com CHINA Co-sleeper V3.indd 20 18/08/2022 10:44...