Advertisement
Wireless Frequency: | 2.4GHz, 802.11b/g | |
Input: | 120VAC, 60Hz | |
Output Power (120VAC): | LED/Fluorescent: 150W Max Incandescent: 400W Max | |
Output Current: | 3.3A | |
Standby Power: | 0.5W | |
Enclosure Type: | Type 1 Enclosure (after installation) | |
Action type: | Type 1.Y action |
Review this installation guide in its entirety before starting installation of your Smart Dimmer Switch or removal of your old switches. Installation and maintenance involving electrical wiring must be done by qualified person(s). Risk of Electric Shock: Electricity can cause personal injury and property damage if handled improperly. An external air gap switch shall be installed before circuit connection to this device. The metal heatsink plate is not grounding, which might become live. Install with plastic Cover Plate only.
NOTE: INSTALLATION OF THIS SMART DIMMER REQUIRES A NEUTRAL WIRE. IF NEUTRAL WIRE IS NOT CONNECTED, THIS DIMMER WILL NOT WORK. CONSULT A QUALIFIED ELECTRICIAN.
To reduce the risk of injury and/or overheating and damage to other equipment:
LIGHTS | INDICATOR LIGHT STATUS | COLOR | STATUS |
Power / Connectivity Indicator Light | ON | WHITE | Powered OFF |
OFF | Powered ON | ||
Single Blink | Ready for Smart Pairing mode | ||
Double Blink | Ready for Manual Pairing mode | ||
Flashing Quickly | RED | Pairing failed | |
Brightness Indicator Lights | 7 LEDs Flashing, Power/Wi-Fi Indicator Light is OFF | WHITE | Operating temperature is too high; switch has been turned off |
0%~14% Brightness Level | |||
14%~28% Brightness Level | |||
28%~42% Brightness Level | |||
42%~56% Brightness Level | |||
56%~70% Brightness Level | |||
70%~84% Brightness Level | |||
84%~100% Brightness Level |
ACTION | COLOR | STATUS |
Short Press | OFF | Dimmer is ON |
Short Press | White | Dimmer is OFF |
Long Press (5 seconds) | White LED Double Blink | Connectivity Mode: Wi-Fi network is acquired |
PROBLEM | CAUSE | SOLUTION |
Unable to find the Smart Dimmer on the network | Smart Dimmer may not be in Connectivity Mode | Long Press the ON/OFF switch (5 seconds) to enter into Connectivity Mode: Searching for Wi-Fi Network. |
Unable to operate the load (light) with the ON/OFF switch | Wiring issue | Review and confirm the INSTALLATION section in this manual. |
No electricity | Check that the power is ON at the circuit breaker. | |
Load does not function or is incompatible |
| |
Smart Dimmer not responding to WiZ APP control | Network is not connected | Check wireless network connectivity. |
Permissions are not granted on mobile device | Check to see that permissions are granted for the WiZ APP. | |
Smart Dimmer is not functioning correctly | Manually press the ON/OFF switch to see electrical functionality is working. | |
Load (light) not functioning properly | Load (light) may not be compatible or exceeding limits |
|
Smart Dimmer not connecting to the WiZ APP | Wi-Fi password is incorrect | Re-enter Wi-Fi password. |
Weak/low Wi-Fi signal | Check Wi-Fi signal to ensure within range of router. | |
Wi-Fi not connected | Confirm Wi-Fi router is broadcasting a 2.4GHz signal. Re-connect. |
Before you start, make sure you install the WiZ App from either Google Play or the Apple App Store (both offer the same set of features). The app can also scale to fit tablets as needed.
The dimmer switch is connected through the app and will only operate on your home's 2.4GHz Wi-Fi network. Most new routers are dual-bandwidth (both 2.4GHz and 5GHz), ensure you select the 2.4GHz network which covers a wider range than the 5GHz. To make sure your phone is on the 2.4GHz network, either select it in the list of available networks on your phone or go into the router settings and temporarily de-activate the 5GHz network (you can activate it again after pairing is done).
If this is not possible and the dimmer switch is not found, try putting the dimmer switch in pairing mode by holding the ON/OFF button for 5 seconds (or until the indicator lights flashes red), then walking a short distance away from the router. Due to the short range of 5GHz networks, your phone should auto-connect to the 2.4GHz at this point. Once connected, you can start pairing in the app. You can pair as many devices as you want at the same time.
Create a home or join an existing one
Name your home
Tap the 'Add room' button to add a room
Name your own or select from the list of standard rooms
Press the 'Add a device' button and enter your Wi-Fi password
Select the 'Wi-Fi Switch' and continue with prompts to connect your device
Note: Upon first boot-up, the firmware may need to be updated. Please allow up to 1 minute for the Smart Dimmer to update after completing WiZ app setup.
For additional support, visit www.liteline.com/WiZsupport
The following importer is the responsible party:
LLC Sales, Inc. DBA Liteline USA
1209 Orange Street, Wilmington, DE, 19801
liteline.com/page/contact-us
Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
RF Exposure Requirements:
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of an least 20cm from all person.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
For complete warranty information, including details on consumer legal rights as well as warranty exclusions, visit www.liteline.com/warranty.
WiFi® is a registered trademark of Wi-Fi Alliance®. Google Play and the Google Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Other trademarks and trade names are those of their respective owners.
LITELINE CORPORATION
Telephone 1.866.730.7704 | Fax 1.888.738.9736 liteline.com
Copyright © 2020, Liteline Corporation. All rights reserved.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download LITELINE LC-CRTL-DIM-1 - Wi-Fi Smart Control With Dimmer Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the LC-CRTL-DIM-1 that isn't answered in the manual? Leave your question here.