FERREX YT-7251A Original User Manual

FERREX YT-7251A Original User Manual

Drywall sander

Advertisement

Quick Links

Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly. In
the event of product failure within its intended use over the course of the
first 3 years after date of purchase, we will remedy the problem as quickly
as possible once it has been brought to our attention. In the unlikely event
of such an occurrence, or if you require any information about the product,
please contact us via our helpline support services, details of which are to be
found both in this manual and on the product itself.
GB
IE
PRODUCED IN CHINA FOR:
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH
ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE
Visit us at www.aldi.com
AFTER SALES SUPPORT
+44(0) 1904727501
+353(0) 19022605
GB
IE
support@coreservice.co.uk
MODEL:
YT-7251A
3
805353
YEAR
WARRANTY
03/2021
User Manual
DRYWALL SANDER
Original User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the YT-7251A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for FERREX YT-7251A

  • Page 1 ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH ALDI STORES (IRELAND) LTD. PO BOX 726, NAAS, CO. KILDARE Visit us at www.aldi.com AFTER SALES SUPPORT 805353 +44(0) 1904727501 +353(0) 19022605 support@coreservice.co.uk YEAR MODEL: WARRANTY YT-7251A 03/2021 Original User Manual...
  • Page 2: Overview

    Overview...
  • Page 3: Package Content List

    Package Content List Package Content List 1 x Drywall Sander 1 x Support Spring 1 x 4 m Suction hose 2 x Hose adaptor (already connected to the hose) 6 x Sanding Paper 1 x Set of spare coal brushes 1 x Allen key 1 x Instruction Manual 1 x Warranty Certificate...
  • Page 5: Table Of Contents

    Table of content Table of content Overview........................2 Package Content List....................3 Package contents/device parts................3 Intended Use......................6 Residual risk......................6 Unpacking....................... 6 Explanation of symbols................... 7 Safety Instructions....................8 General Power Tool Safety Warnings................9 Safety warnings common for sanding operation............11 Kickback and related warnings..................
  • Page 6: Intended Use

    Intended Use Intended Use This drywall sander (referred to below only as "product") is designed for sanding large areas of plasterboard as a preparation before painting or wallpapering. It is designed for domestic use and is not designed for commercial, trade or industrial use.
  • Page 7: Explanation Of Symbols

    Unpacking the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Explanation of symbols The following symbols and signal words are used in this user manual, on the compressor or on the packaging. This signal symbol/word denotes a hazard with WARNING! an average risk level that could lead to death or...
  • Page 8: Safety Instructions

    Safety Instructions Safety Instructions Read the entire owner’s manual carefully and make sure you know how to switch the appliance off in an emergency, before operating the appliance. Do not connect the product to a power source WARNING! until you have read and understood the entire owner’s manual.
  • Page 9: General Power Tool Safety Warnings

    Safety Instructions General Power Tool Safety Warnings Read all safety warnings and all instructions. WARNING! Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Please save this instruction manual. Save all warnings and instructions for future reference.
  • Page 10 Safety Instructions a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Page 11: Safety Warnings Common For Sanding Operation

    Safety Instructions operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g.
  • Page 12 Safety Instructions fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. h. Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires.
  • Page 13: Kickback And Related Warnings

    Safety Instructions q. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Kickback and related warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory.
  • Page 14: Assembly

    Assembly Assembly Always disconnect the plug from the power WARNING! source before making any adjustment or attaching any accessories. Assembling the handle 1. The product features a collapsible handle to enable compact storage. To operate the product, this handle will have to be locked into the operating position.
  • Page 15: Selecting The Right Sanding Paper

    Assembly 5. Rotate the extension handle lock clockwise to secure the extension handle Note: The product can also be used without the extension handle. Selecting the right sanding paper 1. The grain size of the sanding paper is specified on the back of the sanding paper. The smaller the number, the coarser is the grain.
  • Page 16: Installing The Support Spring

    Assembly Installing the support spring 1. It is easier to sand the ceiling when the sanding pad is held at an angle to the handle by installing the support spring 2. To install the support spring, hook one end into the hole in the motor's housing. Fix the other end to the respective receptacle on the handle as shown in Fig.
  • Page 17: Adjusting The Speed Of The Product

    Operation Adjusting the speed of the product 1. To increase the speed of the product, rotate the variable speed dial clockwise. - - low speed for rough grinding. - - high speed for fine grinding. 2. To decrease the speed of the product, rotate the variable speed dial anticlockwise.
  • Page 18: Maintenance

    Cleaning, Maintenance and Storage 3. Never use solvents such as petrol, alcohol, ammonia water etc. These solvents may damage the plastic parts. Maintenance 1. The product has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper care and regular cleaning.
  • Page 19: Troubleshooting

    Troubleshooting Troubleshooting Problem Possible Causes Suggested Solutions Not working No power Insert the plug to the mains properly. Plug or supply cord ist Check and replace the plug or damaged supply cord by an authorised service centre Internal damage or wear e.g. Repair by an authorised service motor is damaged centre.
  • Page 20: Technical Data

    Technical Data Technical Data Model No. YT-7251A Rated voltage 230-240 V~, 50 Hz Rated power 750 W No load speed 1000-1800 min Sanding disc diameter 225 mm Product dimension 1750 x 257 x 270 mm AS/NZS 60745.1 and Standard AS/NZS 60745.2.3...
  • Page 21: Declaration Of Conformity

    Declaration of conformity Original EU Declaration of Conformity MEROTEC GmbH Otto-Brenner-Str. 8, 47877 Willich, Germany herewith declare under our own, sole responsibility that our product Drywall sander Model no. YT-7251A complies with the following directives: 2006/42/EC Machinery Directive 2014/30/EU EMC-Directive 2011/65/EU...
  • Page 22: Disposal

    Disposal Disposal Disposing of packaging Dispose of packaging according to type. Sort the paperboard and cardboard as waste paper and the film as recyclable material. Dispose of old electrical device This symbol indicates that this product may not be disposed of together with domestic waste in compliance with the (2012/19/EU) Regulation pertaining to waste electrical and electronic devices (WEEE).

Table of Contents