Advertisement
Quick Links
Operating Instructions — Parts Manual
Square Wheel Belt Grinder
Models
: 4103, 4106, and 4126AC
WHM TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
www.wmhtoolgroup.com
This Manual is Bookmarked
Part No. 5507796
Revision C2 09/04
Copyright © WMH Tool Group
Advertisement
Related Manuals for Wilton 4103
Summary of Contents for Wilton 4103
- Page 1 This Manual is Bookmarked Operating Instructions — Parts Manual Square Wheel Belt Grinder Models : 4103, 4106, and 4126AC WHM TOOL GROUP 2420 Vantage Drive Part No. 5507796 Elgin, Illinois 60123 Revision C2 09/04 Ph.: 800-274-6848 Copyright © WMH Tool Group...
- Page 2 Exploded View - Square Wheel Belt Grinder...
- Page 3 Parts List - Square Wheel Belt Grinder...
- Page 4 Parts List - Inverter Ref. Part Ref. Part No. Number Description Qty. No. Number Description Qty. 5550874 Screw, Socket head 5508073 Nut, Lock, 10-32 Nylock Cap, 10-32NF x 3/8 5507934 Box, Switch 5507817 inverter (1ph, 120V, 50/60Hz) 9119721 Spade, Female 16-14AWG 5507818 Inverter (3ph, 220V, 50/60Hz) 9117401 Switch, Toggle 5511447 Inverter (3ph, 440V, 50/60Hz)
- Page 5 Exploded View - Vacuum Scoop A vacuum scoop connects the machine to the vacuum system. The mounting provisions for the scoop are shown in the exploded view below. Ref. Part Ref. Part No. Number Description Qty. No. Number Description Qty. 5053531 Scoop Assembly 5053571 Rail 5052471 Adapter, Hose...
- Page 6 Air Cushioned Dead Head Assembly Refer to Figures 10 and 11. The air-cushioned dead head is for use on very small radius grinding. When connected to a source of shop air (80-90 psi), the belt rides on a cushion of air to decrease head and belt wear.
- Page 7 Hub and Wheel Assembly Refer to Figures 12 and 13. The hub and wheel V-Belt assembly Small Diameter Contact Wheels can be used to adapt a number of other optional Collar attachments for use on the belt grinder. The assem- bly consists of a pre-balanced hub shaft, collar, and V-belt and a special wrench to enable quick change of the optional attachments.
- Page 8 Small Diameter Contact Wheels Small diameter contact wheels are useful for grinding or contouring difficult, hard to reach areas (refer to Figure 15). The small diameter contact wheels are available in several sizes. Refer to Figure 14 for a listing of small diameter contact wheels. Dia.
- Page 9 Belt Guard Holes Approximately 1/2-inch from corners Motor Side Holes 20 inches apart Install two 1- inch long screws Install two 1 3/4-inch screws Ref. No. Part Number Description Qty. 5248081 Pedestal 9062121 Socket Head Cap Screw (5/16-18 x 1) 5511051 Socket Head Cap Screw (5/16-18 x 1 3/4) Figure 16: Assembly of Grinding Machine and Pedestal...
- Page 10 Exploded View – Model 5511885 Dust Collection System REAR VIEW FRONT VIEW...
- Page 11 Screw, Hex Head Connection Kits: 5514744 Spacer Refer to Wilton catalog for appropriate connection 5514745 Housing, Outer Fan kit for your grinding machine or contact Wilton for 5514746 Nut, Hex assistance. 5514747 Washer, Lock Wiring Information - Dust Collection System...