Understanding The Status Leds - ADTRAN 854-(v)6 Quick Start Manual

854-(v)6 2.5G Router QSG
Wall Mount Installation
The 854-(v)6 can be mounted on a wall. Wall Mount Kit (17600192F1) can be ordered for mounting the 854-(v)6. Instructions are provided in the
related Quick Start Guide (617600192F1-13).
Supplying Power to the Device
1. Connect the end of the power adapter to the Power port on the back panel of the device
2. Plug the other end of the power adapter into the wall outlet.
3. The SDG will begin powering up immediately as the 854-(v)6 has no on/off power switch.
4. Confirm that the power is connected properly. The Multifunction Status LED should be lit on the front of the device, as described in the
following section "Multifunction Status
Subscriber Connections
The following subscriber connections are available on the 854-(v)6:
■ 2.5G Ethernet port (RJ-45 Connector) - WAN port
■ SFP - WAN port (on bottom of unit)
■ 4x Ethernet port (RJ-45 Connector) – LAN port
■ USB 3.0 (Type A Connector)
■ 2x Voice (RJ-11) interfaces (854-v6 only)
g
NOTE
Only one WAN port may be connected at a time.
To connect the Ethernet interfaces, refer to
port until there is an audible click.
The USB 3.0 host port is reserved for future use. This port currently provides +5 VDC for charging external devices.
Resetting the Device
A reset button is available if the 854-(v)6 needs to be rebooted or restored to factory defaults. To reboot the 854-(v)6, press the Reset button on
the back panel of the device for less than 5 seconds. To reset the device to factory defaults, press the Reset button for 5 seconds or more.
Activating Wi-Fi Protected Setup™
Wi-Fi Protected Setup™ (WPS) is a standard means for creating secure connections between the 854-(v)6 and various wireless client devices. This
feature is designed to simplify the pairing process between the devices. Perform the following steps to activate WPS:
1. Press the WPS button on the back of the 854-(v)6 for less than 5 seconds for 5GHz or more than 5 seconds for 2.4GHz.
2. The WPS LED on the back of the unit is steady green when WPS is on and flashing green when WPS is passing traffic.
3. WPS search mode continues for 2 minutes. The next step must be completed before the 2 minutes have lapsed.
4. In the Wi-Fi settings for the LAN device to be connected to the local network, locate and select the name of the wireless network (SSID) to which
you want to connect. The 854-(v)6 should complete the connection without requiring the password to be manually entered.

Understanding the Status LEDs

A multifunction status LED on the front of the unit and status LED's on the back panel allow you monitor the device status.
Multifunction Status LED
The multifunction status LED on the front of the unit indicates the device status.The meaning of the LED state is different depending on whether
the unit is running SmartOS or PlumeOS.
Color
Blue
Red
Green
Green, Blue
White
Red, Green, Amber
Blue, Red
White
White, Red
6SDG8546V6-13A
LED".
Figure 1 on page 1 and insert a Category 5E (or better) RJ-45 cable into any LAN port and the WAN
Table 2 defines the multifunction status LED state when running SmartOS.
Table 2: Multifunction Status LED for SmartOS
LEDState Event
Solid Cold boot
Pulsing Reboot and system upgrade (persists over uboot)
Pulsing Linux booting up
Pulsing Quick Start
Solid Hub WAN up, Internet
Pulsing Hub WAN down, no Internet
Pulsing Satellite set up
Solid Satellite up
Pulsing Satellite up, fair signal
Understanding the Status LEDs
3