Page 1
H O V E R B O A R D AT TA C H M E N T OPERATION MANUAL H1-RPT-BGY...
Page 2
HELMETS SAVE LIVES! Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride your hoverboard. Incorrect Fit: Correct Fit: Forehead is exposed and Make sure your helmet vulnerable to serious injury. covers your forehead.
Page 3
INTRODUCTION This manual is designed to give you the information you need for the safe operation and maintenance of your new Raptor. Please read it thoroughly before riding your Raptor. WARNING Make sure you read this complete manual before riding your Raptor.
PARTS LIST Tool Set: Wrench (1) Seat Hex Key and Screwdriver (2) Lockers (1) Seat Frame with Suspension (4) Mounting Screws (1) Front Frame (1) Fog Blaster Mount (1) Left Handlebar (4) M8 X 38 Screws (4) M6 X 16 Screws (1) Right Handlebar (4) 8 mm Nuts (1) Fog Blaster...
Page 6
ASSEMBLING YOUR RAPTOR Remove all Raptor contents from the box. Ensure all contents from the “PARTS LIST” section are accounted for. 1. Locate the seat fame. Move the 2 suspension shocks into the u-shaped holders at the rear of the seat frame.
Page 7
2. Insert the left and right handlebar mounts into the seat frame as shown below. Align the holes of the handlebar mounts with the holes in the seat frame. Align the hole of the ag holder with the hole in the seat frame on either side.
Page 8
4. Attach the fog blaster to the fog blaster mount as shown below. Screw in the 4 mounting screws using the screwdriver at the end of the included hex key. Make sure the 2 larger holes of the fog blaster mount are facing forward.
Page 9
6 mm nut. Hold the screws in place with the hex key and turn the nuts clockwise with the wrench to tighten them until the bucket seat is secured. Tools needed 7. Your Raptor is now assembled!
Page 10
FOG BLASTER DIAGRAM 1. Charging Port 2. Water Tank 3. Power Button 4. LED Lights & Sound Effects Button 5. Fog Vent & LED Lights USING & MAINTAINING YOUR FOG BLASTER Before using the fog blaster, connect the included charging cable to the fog blaster’s charging port and a USB outlet (Figure 1).
Page 11
ATTACHING THE RAPTOR TO YOUR HOVERBOARD Carefully follow the instructions shown on the following pages to attach the Raptor to your hoverboard. Read this entire manual before riding your Raptor. Your Raptor must be completely assembled before attaching it to your hoverboard. Please refer to the “ASSEMBLING YOUR RAPTOR”...
Page 12
2. Secure the Raptor to your hoverboard using 2 of the included hook and loop straps. The other 2 straps included are spares. With the fastener side facing away from your hoverboard, thread the straps through the front hole of each handlebar mount.
Page 13
4. WARNING: Do not over-tighten the straps when you are attaching your Raptor to your hoverboard. Ensure that the Raptor is securely attached to the hoverboard. 5. Assemble the flag by inserting one of the included flag rods into the opening in the flag fabric. Attach the coupling tubes to the flag rods.
RAPTOR OPERATION It is important that you fully understand all the functions of your Raptor. If these functions are not used correctly, you will not have full control of your Raptor. Practice using the Raptor at slower speeds in a flat, open area before riding the Raptor in other spaces.
Page 15
PRE-RIDE RAPTOR CHECKLIST Ensure that your Raptor and hoverboard are in proper working order each time you ride. If a part of the Raptor does not function correctly, please contact our Customer Support Center. • Ensure the battery of your hoverboard is fully charged before riding your Raptor.
The first rule of safe riding is to use common sense. The Raptor cannot protect you in a crash, against impact, or from loss of control the way a car can. The Raptor can tip over sideways or pitch you over the front wheel if you don’t ride it properly.
Page 17
CAUTION: RIDING IN WET WEATHER It is recommended that you do not ride your Raptor in wet weather, as the electronic components of the hoverboard may be damaged if exposed to water. Stopping distances can be longer in wet conditions than...
Page 18
2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an accident while riding. 3. Do not make a sharp turns, as you may drift and overturn the Raptor, which can result in injury to yourself and/or damage the unit.
Page 19
RIDING YOUR RAPTOR Ensure your Raptor is fully assembled and correctly attached to your hoverboard with all straps, screws, and nuts secured in place. Ensure your hoverboard is properly maintained as well. Failure to do so may result in damage to the unit, serious bodily harm, or death.